April 5, 2026: LEMON Manuals is launched! Read the announcement.

Adjust The Neutral Position Of Steering Angle Sensor

CAUTION: Always use CONSULT when adjusting the neutral position of steering angle sensor. (It cannot be adjusted other than with CONSULT.)

CHECK THE VEHICLE STATUS (1)
Stop vehicle with front wheels in the straight-ahead position.

Does the vehicle stay in the straight-ahead position?

YES

GO TO 2.

NO

Steer the steering wheel to the straight-ahead position. Stop the vehicle.
ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR
CONSULT
1. Turn the ignition switch ON.
  CAUTION: Never start engine.
2. Select "ABS", "Work support" and "ST ANGLE SENSOR ADJUSTMENT" in this order.
3. Select "START".
  CAUTION: Never touch steering wheel while adjusting steering angle sensor.
4. After approx. 10 seconds, select "END".
5. Turn ignition switch OFF, and then turn it ON again.
  CAUTION: Be sure to perform the operation above.
GO TO 3.

CHECK DATA MONITOR (1)

CONSULT

The vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

Select "ABS", "Data monitor", "ECU INPUT SIGNALS" and "STR ANGLE SIG" in the order. Check that the signal is within the specified value.

STR ANGLE SIG

: 0+/-2.5 deg.

Is the inspection result normal?

YES

GO TO 10.

NO

GO TO 4.

CHECK STEERING COMPONENT PARTS
Check the installation condition of steering component parts. Refer to Inspection .

Is the inspection result normal?

YES

GO TO 5.

NO

Repair or replace error-detected parts. GO TO 5.
CHECK SUSPENSION COMPONENT PARTS
Check the installation condition of suspension component parts.
- Front: Refer to Inspection .
- Rear: Refer to Inspection .
Is the inspection result normal?

YES

GO TO 6.

NO

Repair or replace error-detected parts. GO TO 6.
CHECK WHEEL ALIGNMENT
Check the wheel alignment.
- Front: Refer to Inspection .
- Rear: Refer to Inspection .
Is the inspection result normal?

YES

GO TO 7.

NO

Adjust the wheel alignment. GO TO 7.
- Front: Refer to Adjustment .
CHECK THE VEHICLE STATUS (2)
Stop vehicle with front wheels in the straight-ahead position.

Does the vehicle stay in the straight-ahead position?

YES

GO TO 8.

NO

Steer the steering wheel to the straight-ahead position. GO TO 8.

CHECK DATA MONITOR (2)

CONSULT

The vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

Select "ABS", "DATA ", "ECU INPUT SIGNALS" and "STR ANGLE SIG" in the order. Check that the signal is within the specified value.

STR ANGLE SIG

: 0+/-2.5 deg.

Is the inspection result normal?

YES

GO TO 10.

NO

GO TO 9.

CHECK DATA MONITOR (3)

CONSULT

The vehicle is either pointing straight ahead, or the vehicle needs to be moved.
CAUTION:
- Drive the vehicle at approx. 30 km/h (19MPH) or more for 300 m (985 ft) or more.
- Never use tester
The vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

Select "ABS", "Data Monitor", "ECU INPUT SIGNALS" and "STR ANGLE SIG" in the order. Check that the signal is within the specified value.

STR ANGLE SIG

: 0+/-2.5 deg.

Is the inspection result normal?

YES

GO TO 10.

NO

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY
CONSULT
1. Record or print self-diagnosis results and freeze frame data (FFD).
2. Erase self-diagnosis result of "ABS".
Are the memories erased?

YES

Inspection End.

NO

Check the items indicated by the self-diagnosis.