VEHICROSS (VX) Remote Keyless Entry/Security System Reprogramming (SB00-13-S001)

Publication date: 1970-01-01
Reference number: SB00-13-S001

VEHICROSS (VX) REMOTE KEYLESS ENTRY/SECURITY SYSTEM REPROGRAMMING

TECHNICAL SERVICE BULLETIN

Reference Number(s): SB00-13-S001, Date of Issue: AUGUST, 2000

ISUZU:	1999 - 2000 VehiCROSS
AFFECTED VEHICLES:	1999 - 2000 VehiCROSS (VX) models equipped with Genuine Isuzu remote keyless entry/security system.

Affected Vehicles

1999 - 2000 VehiCROSS (VX) models equipped with Genuine Isuzu remote keyless entry/security system.

Service Information

Included in this bulletin are proper procedures for reprogramming the Genuine Isuzu remote keyless entry/security system. The following quick reference charts are provided for these functions:

INITIAL REMOTE PROGRAMMING
ERASING REMOTE CODES
AUTOMATIC ARMING ON/OFF AND VALET MODE
TURNING CHIRP CONFIRMATION ON/OFF

NOTE: Since the procedures must be done without any deviations, it may require several attempts. For each required reprogramming function, the procedures must be followed and completed in the sequential order as listed and without any interruptions.

Isuzu VehiCROSS Security System

Quick Reference Charts

Fig 1: Remote Programming

Fig 2: Erasing Remote Codes

Fig 3: Automatic Arming On/Off & Valet Mode Preparation Steps

AUTOMATIC ARMING ON

Programming Step

Programming Completion

Open and close the driver's door once.

Turn the ignition switch to OFF⁽¹⁾ .

The system chirps once, and the front marker lights and parking lights flash once.

⁽¹⁾	If you do not turn the Ignition Key to "OFF," or Exceed 30 Seconds During the Programming Steps, the Status Indicator LED will turn Off, and the previous Operation Mode will remain unchanged.

AUTOMATIC ARMING OFF

Programming Step

Programming Completion

Open and close the driver's door twice.

Turn the ignition switch to OFF⁽¹⁾ .

The system chirps twice, and the front marker lights and parking lights flash twice.

⁽¹⁾	If you do not turn the Ignition Key to "OFF," or Exceed 30 Seconds During the Programming Steps, the Status Indicator LED will turn Off, and the previous Operation Mode will remain unchanged.

VALET MODE ON

Programming Step

Programming Completion

Open and close the driver's door 4 times.

Turn the ignition switch to OFF⁽¹⁾ .

The system sounds for 0.6 seconds, and the vehicle's front marker lights and parking lights turn ON for 0.6 seconds.

⁽¹⁾	If you do not turn the Ignition Key to "OFF," or Exceed 30 Seconds During the Programming Steps, the Status Indicator LED will turn Off, and the previous Operation Mode will remain unchanged.

Fig 4: Chirp On/Off Preliminary Steps

CHIRP OFF

Programming Step

Programming Completion

Close the driver's door.

Turn the ignition switch OFF⁽¹⁾ .

The system chirps once, and the front marker lights and parking lights flash once.

⁽¹⁾	If you do not turn the Ignition Key to "OFF," or Exceed 30 Seconds During the Programming Steps, the Status Indicator LED will turn Off, and the previous Operation Mode will remain unchanged.

CHIRP ON

Programming Step

Programming Completion

Close the driver's door, then open and close it again.

Turn the ignition switch OFF⁽¹⁾ .

The system chirps twice, and the front marker lights and parking lights flash twice.

⁽¹⁾	If you do not turn the Ignition Key to "OFF," or Exceed 30 Seconds During the Programming Steps, the Status Indicator LED will turn Off, and the previous Operation Mode will remain unchanged.

NOTE: This Service Bulletin is intended for use by professional, qualified technicians. Attempting repairs or service without the appropriate training, tools, and equipment could cause injury to you or others and damage to your vehicle that may cause it not to operate properly.