Specifications Index
CANYON, COLORADO, I280 & I350 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR-LR-RF-LF. See HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Drum Brakes | DRUM BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine Drive Belts Are Not Adjustable | ||
| Belt Routing | 2.8L DRIVE BELT REPLACEMENT (WITHOUT A/C) or DRIVE BELT REPLACEMENT (WITH A/C) 3.5L DRIVE BELT REPLACEMENT (WITHOUT A/C) or DRIVE BELT REPLACEMENT (WITH A/C) |
||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | |||
| 2.8L & 3.5L | THERMOSTAT REPLACEMENT | ||
| Water Pump R & I | |||
| 2.8L & 3.5L | WATER PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| 2.8L | |||
| Compression | A normal reading should be approximately 215 psi (1482 kPa) The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure - Minimum | 12 psi (85 kPa) @ 1200 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.5L | |||
| Compression | A normal reading should be approximately 215 psi (1482 kPa) The lowest reading should not be less than 70 percent of the highest reading. See ENGINE COMPRESSION TEST |
||
| Oil Pressure - Minimum | 12 psi (85 kPa) @ 1200 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 2.8L & 3.5L | First Pass 30 ft. lbs. (40 N.m) Final Pass + an additional 45 degrees |
||
| Fuel System | |||
| Pressure Specification | 2.8L & 3.5L 50-57 psi (345-395 kPa) | ||
| Fuel Pressure Test Procedure | 2.8L See Fuel Pressure Gage Installation and Removal
and FUEL SYSTEM DIAGNOSIS 3.5L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS |
||
| Fuel Filter Location | 2.8L & 3.5L Manufacturer states A fuel filter is contained in the fuel tank module inside the fuel tank, also see R & I below. | ||
| Fuel Filter R & I | 2.8L See FUEL FILTER REPLACEMENT
and FUEL TANK MODULE REPLACEMENT 3.5L See FUEL FILTER REPLACEMENT and FUEL TANK MODULE REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.8L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.5L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| 2.8L (Type GM P/N 12569190) | |||
| Gap | 0.042 in (1.08 mm) | ||
| Torque | 13 lb ft (18 N.m) | ||
| 3.5L (Type GM P/N 12569190) | |||
| Gap | 0.042 in (1.08 mm) | ||
| Torque | 13 lb ft (18 N.m) | ||
| Starting | |||
| Starter | NA | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 ft. lbs. (140 N.m) | ||