Specifications Index
CANYON, COLORADO, I290 & I370 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 191 Ft. Lbs. (260 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | NA | ||
| Belt Routing | |||
| 2.9L | See figure under DRIVE BELT REPLACEMENT . | ||
| 3.7L | See figure under DRIVE BELT REPLACEMENT . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Radiator cap pressure is stamped on cap. | ||
| Thermostat R & I | ENGINE COOLANT THERMOSTAT REPLACEMENT (WITH 2.9L AND 3.7L) | ||
| Water Pump R & I | WATER PUMP REPLACEMENT (2.9L,3.7L) | ||
| Engine Mechanical | |||
| 2.9L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 12 psi (85 kPa) minimum at 1,200 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.7L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 12 psi (85 kPa) minimum at 1,200 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| First Pass | 30 Ft. Lbs. (40 N.m) | ||
| Final Pass | 45 degrees | ||
| Fuel System | |||
| 2.9L | |||
| Pressure Specification | 50-62 psi (345-427 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter is contained in fuel tank module inside fuel tank. | ||
| Fuel Filter R & I | FUEL TANK MODULE REPLACEMENT | ||
| 3.7L | |||
| Pressure Specification | 50-62 psi (345-427 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter is contained in fuel tank module inside fuel tank. | ||
| Fuel Filter R & I | FUEL TANK MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.9L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.7L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| 2.9L | |||
| Type | GM P/N 12569190 | ||
| Gap | 0.042 In. (1.08 mm) | ||
| Torque | 13 Ft. Lbs. (18 N.m) | ||
| 3.7L | |||
| Type | GM P/N 12598004 | ||
| Gap | 0.040 In. (1.016 mm) | ||
| Torque | 13 Ft. Lbs. (18 N.m) | ||
| Starting | |||
| Starter | STARTING SYSTEM DESCRIPTION AND OPERATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 Ft. Lbs. (140 N.m) | ||