DTC Index

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2009 Jaguar XKR, 2009 Jaguar XK8, 2008 Jaguar XKR, 2008 Jaguar XK8, and 2007 Jaguar XKR. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Prior to carrying out any pinpoint tests on the pedestrian protection system the back-up power supply must be depleted. Disconnect the battery and wait two minutes for the back-up power supply to deplete.

CAUTION: When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number 3548-1358-00.

NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, prior to the installation of a new module/component.

NOTE: Generic scan tools may not read the codes listed, or may read only five digit codes. Match the five digits from the scan tool to the first five digits of the seven digit code listed to identify the fault (the last two digits give additional information read by the manufacturer approved diagnostic system).

NOTE: When performing electrical voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into account.

NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.

NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

DTC	Description	Possible Cause	Action
B100211	Left hood latch deployment control	Left hood latch deployment control circuit - short to ground	Refer to the appropriate system wiring diagram article and test left hood latch deployment control circuit for short to ground
B100212	Left hood latch deployment control	Left hood latch deployment control circuit - short to power	Refer to the appropriate system wiring diagram article and test left hood latch deployment control circuit for short to power
B10021A	Left hood latch deployment control	Left hood latch deployment control circuit - circuit resistance below threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10021B	Left hood latch deployment control	Left hood latch deployment control circuit - circuit resistance above threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10021C	Left hood latch deployment control	Left hood latch deployment control circuit - circuit voltage out of range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10024A	Left hood latch deployment control	Incorrect component installed	Disconnect latch actuator connector, clear DTC and re-test. If DTC remains along with additional DTCs, install a new pedestrian protection module. See Pedestrian Protection Module . If DTC cleared install a new latch actuator. See Pedestrian Protection Latch Actuator .
B100011	Right hood latch deployment control	Right hood latch deployment control circuit - short to ground	Refer to appropriate system wiring diagram article and test right hood latch deployment control circuit for short to ground
B100012	Right hood latch deployment control	Right hood latch deployment control circuit - short to power	Refer to appropriate system wiring diagram article and test right hood latch deployment control circuit for short to power
B10001A	Right hood latch deployment control	Right hood latch deployment control circuit - circuit resistance below threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10001B	Right hood latch deployment control	Right hood latch deployment control circuit - circuit resistance above threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10001C	Right hood latch deployment control	Right hood latch deployment control circuit - circuit voltage out of range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10004A	Right hood latch deployment control	Incorrect component installed	Disconnect latch actuator connector, clear DTC and re-test. If DTC remains along with additional DTCs, install a new pedestrian protection module. See Pedestrian Protection Module . If DTC cleared install a new latch actuator. See Pedestrian Protection Latch Actuator .
B100311	Left hood deployment control	Left hood deployment control circuit - short to ground	Refer to appropriate system wiring diagram article and test left hood deployment control circuit for short to ground
B100312	Left hood deployment control	Left hood deployment control circuit - short to power	Refer to appropriate system wiring diagram article and test left hood deployment control circuit for short to power
B10031A	Left hood deployment control	Left hood deployment control circuit - circuit resistance below threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10031B	Left hood deployment control	Left hood deployment control circuit - circuit resistance above threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10031C	Left hood deployment control	Left hood deployment control circuit - circuit voltage out of range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10034A	Left hood deployment control	Incorrect component installed	Disconnect hood actuator connector, clear DTC and re-test. If DTC remains along with additional DTCs, install a new pedestrian protection module. See Pedestrian Protection Module . If DTC cleared install a new hood actuator. See Pedestrian Protection Hood Actuator LH .
B100111	Right hood deployment control	Right hood deployment control circuit - short to ground	Refer to the appropriate system wiring diagram article and test right hood deployment control circuit for short to ground
B100112	Right hood deployment control	Right hood deployment control circuit - short to power	Refer to the appropriate system wiring diagram article and test right hood deployment control circuit for short to power
B10011A	Right hood deployment control	Right hood deployment control circuit - circuit resistance below threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10011B	Right hood deployment control	Right hood deployment control circuit - circuit resistance above threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10011C	Right hood deployment control	Right hood deployment control circuit - circuit voltage out of range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10014A	Right hood deployment control	Incorrect component installed	Disconnect hood actuator connector, clear DTC and re-test. If DTC remains along with additional DTCs, install a new pedestrian protection module. See Pedestrian Protection Module . If DTC cleared install a new hood actuator. See Pedestrian Protection Hood Actuator RH .
B100613	Pedestrian impact sensor	Pedestrian impact sensor circuit - open circuit	Refer to the appropriate system wiring diagram article and test pedestrian impact sensor circuit for open circuit
B100611	Pedestrian impact sensor	Pedestrian impact sensor circuit - short to ground	Refer to the appropriate system wiring diagram article and test pedestrian impact sensor circuit for short to ground
B100612	Pedestrian impact sensor	Pedestrian impact sensor circuit - short to power	Refer to the appropriate system wiring diagram article and test pedestrian impact sensor circuit for short to power
B100696	Pedestrian impact sensor	Component internal failure	Install a new pedestrian impact sensor. See Pedestrian Impact Sensor .
B100684	Pedestrian impact sensor	Pedestrian impact sensor circuit - signal below allowable range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10064A	Pedestrian impact sensor	Incorrect component installed	Install a new pedestrian impact sensor. See Pedestrian Impact Sensor .
B10061D	Pedestrian impact sensor	Pedestrian impact sensor circuit - current out of range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10068F	Pedestrian impact sensor	Sensor fault	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100631	Pedestrian impact sensor	No signal	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100692	Pedestrian impact sensor	Performance or incorrect operation	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Install new crush pad and air deflectors (even if no damage is apparent). Refer to Front Bumper article.
B100628	Pedestrian impact sensor	Signal bias level out of range/zero adjustment failure	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100654	Pedestrian impact sensor	Missing calibration	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100513	Left pedestrian protection accelerometer	Left pedestrian protection accelerometer circuit - open circuit	Refer to the appropriate system wiring diagram article and test left pedestrian protection accelerometer circuit for open circuit
B100511	Left pedestrian protection accelerometer	Left pedestrian protection accelerometer circuit - short to ground	Refer to the appropriate system wiring diagram article and test left pedestrian protection accelerometer circuit for short to ground
B100512	Left pedestrian protection accelerometer	Left pedestrian protection accelerometer circuit - short to power	Refer to the appropriate system wiring diagram article and test left pedestrian protection accelerometer circuit for short to power
B100596	Left pedestrian protection accelerometer	Component internal failure	Install a new left pedestrian protection accelerometer. See Pedestrian Protection Accelerometer .
B100584	Left pedestrian protection accelerometer	Signal below allowable range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10054A	Left pedestrian protection accelerometer	Incorrect component installed	Install a new left pedestrian protection accelerometer. See Pedestrian Protection Accelerometer .
B10058F	Left pedestrian protection accelerometer	Erratic	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100531	Left pedestrian protection accelerometer	No signal	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100413	Right pedestrian protection accelerometer	Right pedestrian protection accelerometer circuit - open circuit	Refer to appropriate system wiring diagram article and test right pedestrian protection accelerometer circuit for open circuit
B100411	Right pedestrian protection accelerometer	Right pedestrian protection accelerometer circuit - short to ground	Refer to appropriate system wiring diagram article and test right pedestrian protection accelerometer circuit for short to ground
B100412	Right pedestrian protection accelerometer	Right pedestrian protection accelerometer circuit - short to power	Refer to appropriate system wiring diagram article and test right pedestrian protection accelerometer circuit for short to power
B100496	Right pedestrian protection accelerometer	Component internal failure	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100484	Right pedestrian protection accelerometer	Signal below allowable range	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B10044A	Right pedestrian protection accelerometer	Incorrect component installed	Install a new right pedestrian protection accelerometer. See Pedestrian Protection Accelerometer .
B10048F	Right pedestrian protection accelerometer	Erratic	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
B100431	Right pedestrian protection accelerometer	No signal	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U012100	Lost communication with ABS module	Lost communication with ABS module	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U010000	Lost communication with ECM	Lost communication with ECM	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U014200	Lost communication with RJB	Lost communication with RJB	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U000155	High speed CAN communication Bus	Not configured	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U000152	High speed CAN communication Bus	Not configured	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U000188	High speed CAN communication Bus	Bus off	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U1A0266	Permanent memory store full	Signal has too many transitions/events	Install a new pedestrian protection module. See Pedestrian Protection Module . Install new crush pad and air deflectors (even if no damage is apparent). Refer to Front Bumper article.
U300055	Stored vehicle configuration data does not match	Incorrect car configuration data received	Re-configure the RJB using the manufacturer approved diagnostic system. Clear DTC and re-test. If the DTC remains suspect the pedestrian protection system, refer to DTC Index .
U300049	Control module	Internal electronic failure	Install a new pedestrian protection module, refer to DTC Index .
U300087	Control Module	Missing message	Re-configure the RJB using the manufacturer approved diagnostic system. Check pedestrian protection module for DTCs and refer to DTC Index . Check CAN network integrity using the manufacturer approved diagnostic system
U300316	Battery voltage	Circuit voltage below threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U300317	Battery voltage	Circuit voltage above threshold	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
P193429	Vehicle speed signal	Invalid signal	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
P007129	Ambient air temperature sensor range/performance	Invalid signal	Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system
U201B4A	Control module calibration data #2	Incorrect component installed	Install a new pedestrian protection module. See Pedestrian Protection Module .
U201B51	Control module calibration data #2	Not programmed	Re-configure the pedestrian protection module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains install a new pedestrian protection module. See Pedestrian Protection Module .
U210000	Initial configuration not complete	Module is in Plant mode	Place module into normal operation mode, by running the new module programming application, using the manufacturer approved diagnostic system
U300281	Vehicle Identification Number (VIN)	Vehicle/component mis-match. Corrupt VIN data being transmitted, module previously installed to other vehicle	Install original module, check for DTCs and refer to DTC Index .
U030000	Internal control module software incompatibility	Invalid configuration message is received	Re-configure the RJB using the manufacturer approved diagnostic system. Clear the DTC and retest. If the DTC is still logged suspect the pedestrian protection module, refer to DTC Index .