Module Replacement Guide (RF-Hub, Pcm, BCM, ESL)

The Immobilizer Component Replacement guide has been modified to list all of the Immobilizer related procedures, found in wiTECH, listed by priority. Starting with the most important procedure first, along with an "X" to indicate when it is necessary to run this procedure.

Priority	Procedure Name	BCM	ECM	ESL	FOBIKs	RFH
1	Restore Vehicle Configuration	X
2	RFH replacement					X
3	Disable FOBIKs					X
4	Enable FOBIKs				X
5	BCM replacement	X
6	Transfer Secret Key To ESL ECM		X	X
7	PROXI Alignment	X	X	X		X
8	ECU Specific Procedures	X	X	X		X

Priority	Procedure Name	BCM	ECM	ESL	Keys
1	Restore Vehicle Configuration	X
2	BCM replacement	X
3	Program Keys				X
4	Transfer Secret Key To ESL ECM		X	X
5	PROXI Alignment	X	X	X
6	ECU Specific Procedures	X	X	X

The two tables below are the module replacement guide. The first table is for vehicles equipped with passive entry and the second table is for vehicles equipped with a rotary ignition system.

COMPONENT	MODULE REPLACEMENT GUIDE (BCM, Keys, ESL, PCM) PASSIVE ENTRY EQUIPPED
	Condition 1	Condition 2	Condition 3	Condition 4	Condition 5	Condition 6	Condition 7	Condition 8	Condition 9	Condition 10	Condition 11	Condition 12	Condition 13
RFH	New	Existing	Existing	Existing	Existing	New	New	New	New	Existing	Existing	Existing	New
FOBIKs (RKE Only)	Existing	New	Existing	Existing	Existing	New	Existing	Existing	Existing	Existing	Existing	Existing	New
BCM	Existing	Existing	New	Existing	Existing	Existing	New	Existing	Existing	New	New	Existing	New
PCM	Existing	Existing	Existing	New	Existing	Existing	Existing	New	Existing	New	Existing	New	New
ESL	Existing	Existing	Existing	Existing	New	Existing	Existing	Existing	New	Existing	New	New	New
PROGRAMMING ORDER	ASSOCIATED MODULE MISC. FUNCTION
1	RFH replacement	Enable KEYs/FOBIKs (Only the new FOBIK needs to be present, previously stored FOBIKs will remain enabled.)	BCM replacement	Flash the ECM/PCM if the Spare Part is supplied without software	Transfer secret key to ESL / ECM	RFH replacement	BCM replacement (first phase, at a certain point will be asked to configure the RFH, at that point run the RFH replacement, after the RFH replacement and the Disable Fobiks procedures run again the BCM replacement procedure in order to complete the BCM configuration)	RFH replacement	RFH replacement	BCM replacement	BCM replacement	Flash the ECM/PCM if the Spare Part is supplied without software	RFH replacement
2	Disable KEYs/FOBIKs (Only if the procedure did not run automatically after the RFH replacement procedure. All FOBIKs should be present, but the FOBIKs not present at this time will be temporarily disabled. It will be possible to re-enable them by running the Enable KEYs/FOBIKs procedure.)	----	Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen)	Control unit replacement (If available will be found in the ECM ECU.)	PROXI alignment procedure	Disable KEYs/FOBIKs ONLY using the already stored FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure)	RFH replacement	Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure)	Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure)	Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen)	Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen)	Control unit replacement (If available will be found in the ECM ECU.)	Disable KEYs/FOBIKs ONLY using the already stored FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure)
3	RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.)	----	----	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	----	Enable KEYs/FOBIKs ONLY using the new FOBIK(s) and eventually FOBIKs not presented during the Disable KEYs/FOBIKs procedure (Only the new or previously disabled FOBIK needs to be present, previously stored FOBIKs will remain enabled.)	Disable KEYs/FOBIKs (Only if the procedure do not run automatically after the RFH replacement procedure. The FOBIKs not present at this time will be temporarily disabled but will be possible to re-enable them running the Enable KEYs/FOBIKs procedure)	Flash the ECM/PCM if the Spare Part is supplied without software	Transfer secret key to ESL / ECM	Flash the ECM/PCM if the Spare Part is supplied without software	Transfer secret key to ESL / ECM	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	Enable KEYs/FOBIKs ONLY using the new FOBIK(s) and eventually FOBIKs not presented during the Disable KEYs/FOBIKs procedure (Only the new or previously disabled FOBIK needs to be present, previously stored FOBIKs will remain enabled.)
4	Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID	----	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	----	----	BCM replacement (second phase, in order to complete the BCM configuration)	Control unit replacement (If available will be found in the ECM ECU.)	PROXI alignment procedure	Control unit replacement (If available will be found in the ECM ECU.)	PROXI alignment procedure	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	BCM replacement
5	----	----	----	----	----	----	RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.)	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.)	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	----	----	Run BCM ECU Reset (Found under the Diagnostic Procedures Tab of the Vehicle View screen)
6	----	----	----	----	----	----	Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	----	----	Flash the ECM/PCM if the Spare Part is supplied without software
7	----	----	----	----	----	----	----	----	----	----	----	----	Control unit replacement (If available will be found in the ECM ECU.)
8	----	----	----	----	----	----	----	----	----	----	----	----	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)
9	----	----	----	----	----	----	----	----	----	----	----	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)
10	----	----	----	----	----	----	----	----	----	----	----	----	RFH_TPM Update FF_FR Axle Nom Tire Press Val (only if the vehicle is equipped with TPM sensors, or if the current pressure value set by the RFH replacement routine is different from the expected due to aftermarket tire size on the vehicle.)
11	----	----	----	----	----	----	----	----	----	----	----	----	Program Left Front Tire Sensor ID, Program Left Rear Tire Sensor ID, Program Right Front Tire Sensor ID, and Program Right Rear Tire Sensor ID

COMPONENT	MODULE REPLACEMENT GUIDE (BCM, Keys, ESL, PCM) ROTARY KEY EQUIPPED
COMPONENT	Condition 1	Condition 2	Condition 3	Condition 4	Condition 5	Condition 6	Condition 7	Condition 8	Condition 9
BCM	New	Existing	Existing	Existing	New	New	New	Existing	New
FOBIKs (RKE Only)	Existing	New	Existing	Existing	New	Existing	Existing	Existing	New
PCM	Existing	Existing	New	Existing	Existing	New	Existing	New	New
ESL	Existing	Existing	Existing	New	Existing	Existing	New	New	New
PROGRAMMING ORDER	ASSOCIATED MODULE MISC. FUNCTION
1	BCM replacement	Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.)	Flash the ECM/PCM if the Spare Part is supplied without software	Transfer secret key to ESL / ECM	BCM replacement	BCM replacement	BCM replacement	Flash the ECM/PCM if the Spare Part is supplied without software	BCM replacement
2	----	----	Control unit replacement (If available will be found in the ECM ECU.)	PROXI alignment procedure	Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.)	Flash the ECM/PCM if the Spare Part is supplied without software	Transfer secret key to ESL / ECM	Control unit replacement (If available will be found in the ECM ECU.)	Program Keys (All the available Keys must be present during the procedure. Any keys not present at this time will be disabled FOREVER.)
3	----	----	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	----	----	Control unit replacement (If available will be found in the ECM ECU.)	PROXI alignment procedure	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	Flash the ECM/PCM if the Spare Part is supplied without software
4	----	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	----	----	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	Control unit replacement (If available will be found in the ECM ECU.)
5	----	----	----	----	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)	----	----	Transfer secret key to ESL / ECM (only if the Control unit replacement procedure was not available in previous step.)
6	----	----	----	----	----	----	----	----	PROXI alignment procedure (only if the Control unit replacement procedure was not available in previous step.)