Specifications Index
FORTE & FORTE KOUP SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | See TIGHTENING TORQUE SPECIFICATION table under WHEN INSTALLING CONNECTING PARTS and applicable component in AIR CONDITIONING SYSTEM article. | ||
| Axle Nut/Hub Nut | |||
| Front | 196.1~274.5 N.m (20.0~28.0 Kgf.m, 144.6~202.5 lb.ft) | ||
| Rear | 90~110 N.m (9.0~11.0 Kgf.m, 65~80 lb.ft) | ||
| Battery | CHARGING SYSTEM SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Drum Brakes | |||
| Service Specifications | SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUES | ||
| Charging | |||
| Generator | CHARGING SYSTEM SPECIFICATIONS | ||
| Torque | CHARGING SYSTEM | ||
| Drive Belts | |||
| Adjustment | Auto tensioner | ||
| Drive Belt Routing | See appropriate figure under REMOVAL . | ||
| Engine Cooling | |||
| General Service Specifications | See GENERAL SPECIFICATIONS . | ||
| Radiator Cap Pressure | 16 psi | ||
| Thermostat R & I | REPAIR PROCEDURES | ||
| Water Pump R & I | REPAIR PROCEDURES | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil Pressure | 15.6 psi (108 kPa) or above at 1000 RPM with oil temperature at 230± 36°F (110±2°C). | ||
| Overhaul | GENERAL SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| 2.4L | |||
| Compression | COMPRESSION PRESSURE INSPECTION | ||
| Oil Pressure | 21.3 psi (108 kPa) or above at 1000 RPM with oil temperature at 230± 36°F (110±2°C). | ||
| Overhaul | GENERAL SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 86.8-93.9 ft. lbs. (117.6-127.4 N.m) | ||
| Fuel System | |||
| Pressure Specification | 49-50.5 psi (338-348 kPa) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | FUEL FILTER | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | 1-3-4-2. No. 1 cylinder is closest to water pump. | ||
| Ignition Coil (Resistance) | |||
| Standard value | 0.62Ω ± 10% | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| Type: FK16HQR11 | |||
| Gap | 0.0394-0.0433 in. (1.0-1.1 mm) | ||
| Torque | 15-21 ft. lb. (20-30 N.m) | ||
| Starting | |||
| Starter | STARTING SYSTEM SPECIFICATIONS | ||
| Torque | REMOVAL | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | TIGHTENING TORQUES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 65-80 ft. lbs. (90-110 N.m) | ||