Common Specs & Procedures Index

SPORTAGE COMMON SPECS & PROCEDURES

System			Specification/Procedure
Air Conditioning
Service			SPECIFICATION
Torque			See TIGHTENING TORQUE REFERENCE CHART under WHEN INSTALLING CONNECTING PARTS .
	Axle Nut/Hub Nut
	Front		145-203 ft. lbs. (196-275 N.m)
	Rear		145-203 ft. lbs. (196-275 N.m)
Battery
2.0L			Refer to BATTERY and CHARGING SYSTEM .
2.4L			Refer to BATTERY and CHARGING SYSTEM .
Brakes
Bleeding Sequence			BLEEDING OF BRAKE SYSTEM
Disc Brakes			SPECIFICATIONS
Drum Brakes (Parking Brake)			SPECIFICATIONS
Torque			TIGHTENING TORQUES
Charging
Generator
	2.0L		CHARGING SYSTEM
	2.4L		CHARGING SYSTEM
	Torque
	2.0L		Refer to tightening torque under REMOVAL AND INSTALLATION .
	2.4L		Refer to tightening torque under REMOVAL AND INSTALLATION .
Drive Belts
Adjustment			Auto-Tensioner Used
Belt Routing
		2.0L	See "Turning Drive Belt Tensioner Counterclockwise" figure under REMOVAL AND INSTALLATION .
		2.4L	See "Turning Drive Belt Tensioner" figure under REMOVAL AND INSTALLATION .
Engine Cooling
2.0L
General Service Specifications			Refer to Cooling System under SPECIFICATIONS .
Radiator Cap Pressure			14-18 psi
Thermostat R & I			THERMOSTAT
Water Pump R & I			WATER PUMP
2.4L
General Service Specifications			Refer to Cooling System under SPECIFICATIONS .
Radiator Cap Pressure			14-18 psi
Thermostat R & I			THERMOSTAT .
Water Pump R & I			WATER PUMP
Engine Mechanical
2.0L
Compression			COMPRESSION PRESSURE INSPECTION
Oil Pressure			Oil pressure should be 117.68 kPa (1.2 kgf/cm² , 17.07 psi) or above at 1000 RPM.
Overhaul			SPECIFICATIONS
Torque			TIGHTENING TORQUES
2.4L
Compression			COMPRESSION PRESSURE INSPECTION
Oil Pressure			Oil pressure should be 147 kPa (1.5 kgf/cm² , 21.3 psi) or above at 1000 RPM.
Overhaul			SPECIFICATIONS
Torque			TIGHTENING TORQUES
Fluid Specifications			See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flexplate Torque
	2.0L		86.8-94 ft. lbs. (117.7-127.5 N.m)
	2.4L		86.8-94 ft. lbs. (117.7-127.5 N.m)
Fuel System
2.0L
Fuel Filter Location			Fuel filter is part of fuel pump.
Fuel Filter Removal & Installation			FUEL PUMP
Fuel Pressure Specification			493-507 kPa (5.0-5.2 kgf/cm² , 71.5-73.5 psi)
Fuel Pressure Test Procedure			FUEL PRESSURE TEST
Fuel Pressure Release Procedure			RELEASE RESIDUAL PRESSURE IN FUEL LINE
2.4L
Fuel Filter Location			Fuel filter is part of fuel pump.
Fuel Filter Removal & Installation			FUEL PUMP
Fuel Pressure Specification			324-363 kPa (3.3-3.7 kgf/cm² , 46.9-52.6 psi)
Fuel Pressure Test Procedure			FUEL PRESSURE TEST
Fuel Pressure Release Procedure			RELEASE RESIDUAL PRESSURE IN FUEL LINE
Ignition
2.0L
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)			IGNITION SYSTEM
Ignition Wires (Routing)			Coil On Plug Design
2.4L
Firing Order & Cylinder Identification			FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance)			IGNITION SYSTEM
Ignition Wires (Routing)			Coil On Plug Design
Spark Plugs
2.0L			IGNITION SYSTEM
2.4L			IGNITION SYSTEM
Starting
2.0L
Starter			STARTING SYSTEM
Torque			Refer to tightening torque under REMOVAL AND INSTALLATION .
2.4L
Starter			STARTING SYSTEM
Torque			Refer to tightening torque under REMOVAL AND INSTALLATION .
Wheel Alignment
Adjustment Specifications			ALIGNMENT
Torque			Refer to appropriate TIGHTENING TORQUE SPECIFICATIONS table under SPECIFICATIONS .
Wheel & Tire
Lug Nut Torque			65-80 ft. lbs. (88-108 N.m)