LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Kia >> 2021 >> Telluride SX, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Collision/Avoidance >> Front View Camera System >> Front View Camera Unit >> Repair Procedures >> Adjustment >> Service Point Target Auto Calibration (SPTAC) Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Service Point Target Auto Calibration (SPTAC) Procedure

  1. Install the SST (09964-C1200) on the roof center above the vehicle's front windshield.
    G13312850Courtesy of KIA MOTORS AMERICA, INC.
  2. Have the laser illuminate starting from the roof center and to passing through the emblem center.
    G13312851Courtesy of KIA MOTORS AMERICA, INC.

    Information 

    CAUTION: The level laser must be set to 'ON' and the holding (locking) function is not used.
    G13312852Courtesy of KIA MOTORS AMERICA, INC.
  3. Place the calibration target (09890-3V100) so that it adheres by 0 cm to the bumper front. [max. tolerance: 5 cm (1.97 in.)]
    G13312853Courtesy of KIA MOTORS AMERICA, INC.
  4. Set the calibration target height to 90 ± 1 cm (35.43 ± 0.39 in.) from the ground and align the center of calibration target with center line (A) of laser beam.
    G13312854Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • The vehicle horizontal plane shall be completely parallel to the target horizontal plane (0 degree).
    • Align the calibration target (09890-3V100) referring to the below tolerance angle.
      G13312855Courtesy of KIA MOTORS AMERICA, INC.
      G13312856Courtesy of KIA MOTORS AMERICA, INC.
    • Mounting area must not have cross hatch patterns or textual markings near the target.
    • Target should be well lit for optimal performance using non-fluctuating illumination. There shall be no continuous shadows cast on the target.
    • The light should be directed toward the target front and the target front should be brighter than the target rear and target.
  5. Perform the "SPTAC Calibration" using the KDS.
    G13312857Courtesy of KIA MOTORS AMERICA, INC.
    G13312858Courtesy of KIA MOTORS AMERICA, INC.
    G13312859Courtesy of KIA MOTORS AMERICA, INC.
  6. Perform the short-distance calibration by selecting the "OK" message on the KDS after checking the calibration target location.
    G13312860Courtesy of KIA MOTORS AMERICA, INC.
    G13312861Courtesy of KIA MOTORS AMERICA, INC.
  7. Move the calibration target (09890-3V100) at 100 cm (39.37 in.) from the bumper. [max. tolerance: ± 5 cm (± 1.97 in.)]
    G13312862Courtesy of KIA MOTORS AMERICA, INC.
  8. Align the center of calibration target with center line (A) of laser beam.
    G13312863Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • The vehicle horizontal plane shall be completely parallel to the target horizontal plane (0 degree).
    • Align the calibration target (09890-3V100) referring to the below tolerance angle.
      G13312864Courtesy of KIA MOTORS AMERICA, INC.
      G13312865Courtesy of KIA MOTORS AMERICA, INC.
    • Mounting area must not have cross hatch patterns or textual markings near the target.
    • Target should be well lit for optimal performance using non-fluctuating illumination. There shall be no continuous shadows cast on the target.
    • The light should be directed toward the target front and the target front should be brighter than the target rear and target.
  9. Perform the long-distance calibration by selecting the "OK" message on the KDS after checking the calibration target location.
    G13312866Courtesy of KIA MOTORS AMERICA, INC.
    G13312867Courtesy of KIA MOTORS AMERICA, INC.
    G13312868Courtesy of KIA MOTORS AMERICA, INC.
  10. Clear the diagnostic trouble codes (DTC) using the KDS.
  11. Check the DTC and warning lamp.
scientia non olet · About LEMON Manuals