Restraints Control Module (RCM)

WARNING: This page is about a different car, the 2012 Land Rover Range Rover Sport and 2011 Land Rover Range Rover Sport. However, it is still accessible from the selected car via links, so may be relevant.

WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS. TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT ONE MINUTE. FAILURE TO FOLLOW THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY.

CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee confirmation of a fault, and may also cause additional faults in the vehicle being checked and/or the donor vehicle.

NOTE: Given the legal implications of a restraints system failure, harness repairs to Air Bag module circuits are not acceptable. Where the text refers to "REPAIR the circuit", this will normally mean the replacement of a harness.

NOTE: When performing electrical voltage or resistance checks, always use a digital multimeter (DMM) accurate to three decimal places, and with an up-to-date calibration certificate. When checking resistance, always take the resistance of the DMM leads into account.

NOTE: If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty Policy and Procedures information or determine if any prior approval program is in operation, prior to the installation of a new module/component.

NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint checks.

NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.

NOTE: If DTCs are recorded and, after performing the pinpoint checks, a fault is not present, an intermittent concern may be the cause. Always check for loose connections and corroded terminals.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Restraints Control Module, for additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing. Refer to AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) .

DTC	Description	Possible Causes	Action
B0001-11	Driver Frontal Stage 1 Deployment Control - Circuit short to ground	Driver Airbag Ignitor Stage 1 circuit short circuit to ground	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 1) circuit for short to ground
B0001-12	Driver Frontal Stage 1 Deployment Control - Circuit short to battery	Driver Airbag Ignitor Stage 1 circuit short circuit to power	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 1) circuit for short to power
B0001-1A	Driver Frontal Stage 1 Deployment Control - Circuit resistance below threshold	Driver Airbag Ignitor Stage 1 circuit resistance below threshold	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 1) circuit for short circuit. Check connector security at clockspring and airbag
B0001-1B	Driver Frontal Stage 1 Deployment Control - Circuit resistance above threshold	Driver Airbag Ignitor Stage 1 open circuit, high resistance	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 1) circuit for open circuit high resistance
B0001-64	Driver Frontal Stage 1 Deployment Control - Signal plausibility failure	Driver Airbag Ignitor Stage 1 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0001-95	Driver Frontal Stage 1 Deployment Control - incorrect assembly	Driver Airbag Ignitor (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 1) circuit for faults
B0002-11	Driver Frontal Stage 2 Deployment Control - Circuit short to ground	Driver Airbag Ignitor (Stage 2) circuit short circuit to ground	Refer to the electrical circuit diagrams and check Driver Airbag Ignitor (Stage 2) circuit for short to ground
B0002-12	Driver Frontal Stage 2 Deployment Control - Circuit short to battery	Driver Airbag Ignitor (Stage 2) circuit short circuit to power	Refer to the electrical circuit diagrams and check Driver Airbag Ignitor (Stage 2) circuit for short to power
B0002-1A	Driver Frontal Stage 2 Deployment Control - Circuit resistance below threshold	Driver Airbag Ignitor (Stage 2) circuit resistance below threshold	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 2) circuit for short circuit (Check connector security at clockspring and airbag)
B0002-1B	Driver Frontal Stage 2 Deployment Control - Circuit resistance above threshold	Driver Airbag Ignitor (Stage 2) high circuit resistance, open circuit	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 2) circuit for high resistance, open circuit
B0002-64	Driver Frontal Stage 2 Deployment Control - Signal plausibility failure	Driver Airbag Ignitor (Stage 2) configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0002-95	Driver Frontal Stage 2 Deployment Control - incorrect assembly	Driver Airbag Ignitor (Stage 2) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Driver Airbag Ignitor (Stage 2) circuit for faults
B0010-11	Passenger Frontal Stage 1 Deployment Control - Circuit short to ground	Front Passenger Airbag Ignitor (Stage 1) circuit short circuit to ground	Refer to the electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 1) circuit for short to ground
B0010-12	Passenger Frontal Stage 1 Deployment Control - Circuit short to battery	Front Passenger Airbag Ignitor (Stage 1) circuit short circuit to power	Refer to the electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 1) circuit for short to power
B0010-1A	Passenger Frontal Stage 1 Deployment Control - Circuit resistance below threshold	Front Passenger Airbag Ignitor (Stage 1) circuit resistance below threshold	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 1) circuit for short circuit (Check connectors for security)
B0010-1B	Passenger Frontal Stage 1 Deployment Control - Circuit resistance above threshold	Front Passenger Airbag Ignitor (Stage 1) high circuit resistance, open circuit	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 1) circuit for high resistance or open circuit
B0010-64	Passenger Frontal Stage 1 Deployment Control - Signal plausibility failure	Front Passenger Airbag Ignitor (Stage 1) configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0010-95	Passenger Frontal Stage 1 Deployment Control - incorrect assembly	Front Passenger Airbag Ignitor (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 1) circuit for faults
B0011-11	Passenger Frontal Stage 2 Deployment Control - Circuit short to ground	Front Passenger Airbag Ignitor (Stage 2) circuit short circuit to ground	Refer to the electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 2) circuit for short to ground
B0011-12	Passenger Frontal Stage 2 Deployment Control - Circuit short to battery	Front Passenger Airbag Ignitor (Stage 2) circuit short circuit to power	Refer to the electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 2) circuit for short to power
B0011-1A	Passenger Frontal Stage 2 Deployment Control - Circuit resistance below threshold	Front Passenger Airbag Ignitor (Stage 2) circuit resistance below threshold	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 2) circuit for short circuit (Check connectors for security)
B0011-1B	Passenger Frontal Stage 2 Deployment Control - Circuit resistance above threshold	Front Passenger Airbag Ignitor (Stage 2) high circuit resistance, open circuit	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 2) circuit for high resistance or open circuit
B0011-64	Passenger Frontal Stage 2 Deployment Control - Signal plausibility failure	Front Passenger Airbag Ignitor (Stage 2) configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0011-95	Passenger Frontal Stage 2 Deployment Control - incorrect assembly	Front Passenger Airbag Ignitor (Stage 2) Incorrect assembly short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Front Passenger Airbag Ignitor (Stage 2) circuit for faults
B0020-11	Left Side Air Bag Deployment Control - Circuit short to ground	Left hand Side Airbag Ignitor circuit short circuit to ground	Refer to the electrical circuit diagrams and check left hand Side Airbag Ignitor circuit for short to ground
B0020-12	Left Side Air Bag Deployment Control - Circuit short to battery	Left hand Side Airbag Ignitor circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Side Airbag Ignitor circuit for short to power
B0020-1A	Left Side Air Bag Deployment Control - Circuit resistance below threshold	Left hand Side Airbag Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and check left hand Side Airbag Ignitor circuit for short circuit (Check connectors for security)
B0020-1B	Left Side Air Bag Deployment Control - Circuit resistance above threshold	Left hand Side Airbag Ignitor high circuit resistance, open circuit	Refer to electrical circuit diagrams and check left hand Side Airbag Ignitor circuit for high resistance or open circuit
B0020-64	Left Side Air Bag Deployment Control - Signal plausibility failure	Left hand Side Airbag Ignitor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0020-95	Left Side Airbag Deployment Control - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand Side Airbag Ignitor circuit for faults
B0021-11	Left Curtain Deployment Control 1 - Circuit short to ground	Left hand Curtain Ignitor circuit short circuit to ground	Refer to the electrical circuit diagrams and check left hand Curtain Ignitor circuit for short to ground
B0021-12	Left Curtain Deployment Control 1 - Circuit short to battery	Left hand Curtain Ignitor circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Curtain Ignitor circuit for short to power
B0021-1A	Left Curtain Deployment Control 1 - Circuit resistance below threshold	Left hand Curtain Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and check left hand Curtain Ignitor circuit for short circuit (Check connectors for security)
B0021-1B	Left Curtain Deployment Control 1 - Circuit resistance above threshold	Left hand Curtain Ignitor high circuit resistance, open circuit	Refer to electrical circuit diagrams and check left hand Curtain Ignitor circuit for high resistance or open circuit
B0021-64	Left Curtain Deployment Control 1 - Signal plausibility failure	Left hand Curtain Ignitor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0021-95	Left Curtain Deployment Control 1 - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check left hand Curtain Ignitor circuit for faults
B0022-11	Left Curtain Deployment Control 2 - circuit short to ground	Left hand Curtain (row 3) Ignitor circuit short circuit to ground	Refer to the electrical circuit diagrams and check Left Side Curtain (Row 3) Ignitor circuit for short to ground
B0022-12	Left Curtain Deployment Control 2 - circuit short to battery	Left hand Curtain (row 3) Ignitor circuit short circuit to power	Refer to the electrical circuit diagrams and check Left Side Curtain (Row 3) Ignitor circuit for short to power
B0022-1A	Left Deployment Control 2 - circuit resistance below threshold	Left hand Curtain (row 3) Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and check Left Side Curtain (Row 3) Ignitor circuit for short circuit (Check connectors for security)
B0022-1B	Left Curtain Development control 2 - circuit resistance above threshold	Left hand Curtain (row 3) Ignitor high circuit resistance, open circuit	Refer to electrical circuit diagrams and check Left Side Curtain (Row 3) Ignitor circuit for high resistance or open circuit
B0022-64	Left Curtain Development Control 2 - signal plausibility failure	Left hand Curtain (row 3) Ignitor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0022-95	Left Curtain Development Control 2 - incorrect assembly	* Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Left Side Curtain (Row 3) Ignitor circuit for faults
B0028-11	Right Side Air Bag Deployment Control - Circuit short to ground	Right side air bag circuit short circuit to ground	Refer to the electrical circuit diagrams and check Right Side Airbag Ignitor circuit for short to ground
B0028-12	Right Side Air Bag Deployment Control - Circuit short to battery	Right side air bag circuit short circuit to power	Refer to the electrical circuit diagrams and check Right Side Airbag Ignitor circuit for short to power
B0028-1A	Right Side Air Bag Deployment Control - Circuit resistance below threshold	Right Side Air Bag circuit resistance below threshold	Refer to electrical circuit diagrams and check Right Side Airbag Ignitor circuit for short circuit (Check connectors for security)
B0028-1B	Right Side Air Bag Deployment Control - Circuit resistance above threshold	Right Side Air Bag circuit open circuit, high resistance, open circuit	Refer to electrical circuit diagrams and check Right Side Airbag circuit for high resistance or open circuit
B0028-64	Right Side Air Bag Deployment Control - Signal plausibility failure	Right Side Air Bag configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0028-95	Right Side Airbag Deployment Control - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Right Side Airbag Ignitor circuit for faults
B0029-11	Right Curtain Deployment Control 1 - Circuit short to ground	Right Curtain Ignitor circuit short circuit to ground	Refer to the electrical circuit diagrams and check Right Curtain Ignitor circuit for short to ground
B0029-12	Right Curtain Deployment Control 1 - Circuit short to battery	Right Curtain Ignitor circuit short circuit to power	Refer to the electrical circuit diagrams and check Right Curtain Ignitor circuit for short to power
B0029-1A	Right Curtain Deployment Control 1 - Circuit resistance below threshold	Right Curtain Ignitor circuit resistance below threshold	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for short circuit (Check connectors for security)
B0029-1B	Right Curtain Deployment Control 1 - Circuit resistance above threshold	Right Curtain Ignitor high circuit resistance	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for high resistance or open circuit
B0029-64	Right Curtain Deployment Control 1 - Signal plausibility failure	Right Curtain Ignitor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0029-95	Right Curtain Deployment Control 1 - incorrect assembly	Incorrect assembly - short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check Right Curtain Ignitor circuit for faults
B0050-11	Driver Seatbelt Sensor - Circuit short to ground	Driver Seatbelt Switch circuit short circuit to ground	Refer to the electrical circuit diagrams and check Driver Seatbelt Switch circuit for short to ground
B0050-12	Driver Seatbelt Sensor - Circuit short to battery	Driver Seatbelt Switch circuit short circuit to power	Refer to the electrical circuit diagrams and check Driver Seatbelt Switch circuit for short to power
B0050-1D	Driver Seatbelt Sensor - Circuit current out of range	Driver Seatbelt Switch circuit short circuit to ground, short circuit to power, open circuit	Refer to the electrical circuit diagrams and check Driver Seatbelt Switch circuit for short to ground, short to power, open circuit
B0050-64	Driver Seatbelt Sensor - Signal plausibility failure	Driver Seatbelt Switch configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0090-11	Left Frontal Restraints Sensor - Circuit short to ground	Left hand Front Crash Sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and check left hand Front Crash Sensor circuit for short to ground
B0090-12	Left Frontal Restraints Sensor - Circuit short to battery	Left hand Front Crash Sensor circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Front Crash Sensor circuit for short to power
B0090-64	Left Frontal Restraints Sensor - Signal plausibility failure	Left hand Front Crash Sensor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0090-81	Left Frontal Restraints Sensor - invalid serial data received	Left hand Front Crash Sensor circuit, open circuit Left hand Front Crash Sensor internal failure	Refer to the electrical circuit diagrams and check left hand Front Crash Sensor circuit for open circuit fault. Check and Check and install a new Left Frontal Restraints sensor as required
B0090-92	Left Frontal Restraints Sensor - performance or incorrect operation	Left hand Front Crash Sensor internal failure	Check component fixings for security. If secure suspect left hand Front Crash Sensor internal fault. Check and instal a new left hand Front Crash Sensor as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0090-96	Left Frontal Restraints Sensor - component internal failure	Left hand Front Crash Sensor internal failure	Check and instal a new left hand Front Crash Sensor as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0091-11	Left Side Restraints Sensor 1 - Circuit short to ground	Left hand Side Crash Sensor 1 circuit - short circuit to ground	Refer to the electrical circuit diagrams and check left hand Side Crash 1 (Door) Sensor circuit for short to ground
B0091-12	Left Side Restraints Sensor 1 - Circuit short to battery	Left hand Side Crash Sensor 1 circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor 1(Door) circuit for short to power
B0091-64	Left Side Restraints Sensor 1 - Signal plausibility failure	Left hand Side Crash Sensor 1 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0091-81	Left Side Restraints Sensor 1 - invalid serial data received	Left hand Side Crash Sensor 1 circuit open circuit Left Side Restraints Sensor 2 failure	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor 1(Door) circuit for open circuit fault. Check and install a new Left Side Restraints Sensor 1 (Door) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0091-92	Left Side Restraints Sensor 1 - performance or incorrect operation	Left hand Side Crash Sensor 1 component internal failure	Check and install a new left hand Side Restraints Sensor 1 (Door) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0091-96	Left Side Restraints Sensor 1 - component internal failure	Left hand Side Crash Sensor 1 component internal failure	Check and install a new left hand Side Restraints Sensor 1 (Door) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0092-11	Left Side Restraints Sensor 2 - Circuit short to ground	Left hand Side Crash Sensor 2 circuit - short circuit to ground	Refer to the electrical circuit diagrams and check left hand Side Crash (B Pillar) Sensor circuit for short to ground
B0092-12	Left Side Restraints Sensor 2 - Circuit short to battery	Left hand Side Crash Sensor 2 circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor (B Pillar) circuit for short to power
B0092-64	Left Side Restraints Sensor 2 - Signal plausibility failure	Left hand Side Crash Sensor 2 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0092-81	Left Side Restraints Sensor 2 - invalid serial data received	Left hand Side Crash Sensor 2 circuit open circuit Left Side Restraints Sensor 2 internal failure	Refer to the electrical circuit diagrams and check left hand Side Crash Sensor (B Pillar) circuit for open circuit fault. Check and install a new Left Side Restraints Sensor 2 (B Pillar) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0092-92	Left Side Restraints Sensor 2 - performance or incorrect operation	Left hand Side Crash Sensor 2 component internal failure	Check and install a new Left Side Restraints Sensor 2 (B Pillar) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0092-96	Left Side Restraints Sensor 2 - component internal failure	Left hand Side Crash Sensor 2 component internal failure	Check and install a new Left Side Restraints Sensor 2 (B Pillar) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0093-11	Left Side Restraints Sensor 3 - Circuit short to ground	Left hand Rear Side Crash Sensor 3 circuit short circuit to ground	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for short to ground
B0093-12	Left Side Restraints Sensor 3 - Circuit short to battery	Left hand Rear Side Crash Sensor 3 circuit short circuit to power	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for short to power
B0093-64	Left Side Restraints Sensor 3 - Signal plausibility failure	Left hand Rear Side Crash Sensor 3 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0093-81	Left Side Restraints Sensor 3 - invalid serial data received	Left hand Rear Side Crash Sensor 3 circuit - open circuit Right Side Restraints Sensor 3 failure	Refer to the electrical circuit diagrams and check left hand Rear Side Crash Sensor 3 circuit for open circuit fault. Check and install a new Right Side Restraints Sensor 3 as required
B0093-92	Left Side Restraints Sensor 3 - performance or incorrect operation	Left hand Rear Side Crash Sensor 3 component internal failure	Check and install a new left hand Rear Side Restraints Sensor 3 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0093-96	Left Side Restraints Sensor 3 - component internal failure	Left hand Rear Side Restraints Sensor 3 internal failure	Suspect left hand Rear Side Crash Sensor 3 internal fault. Check and install a new left hand Rear Side Restraints Sensor 3 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0095-11	Right Frontal Restraints Sensor - Circuit short to ground	Right hand Front Crash Sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and check right hand Front Crash Sensor circuit for short to ground
B0095-12	Right Frontal Restraints Sensor - Circuit short to battery	Right hand Front Crash Sensor circuit short circuit to power	Refer to the electrical circuit diagrams and check right hand Front Crash Sensor circuit for short to power
B0095-64	Right Frontal Restraints Sensor - Signal plausibility failure	Right hand Front Crash Sensor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0095-81	Right Frontal Restraints Sensor - invalid serial data received	Right hand Front Crash Sensor open circuit right hand Front Crash Sensor failure	Refer to the electrical circuit diagrams and check right hand Front Crash Sensor circuit for open circuit fault. Check and install a new Right Frontal Restraints sensor as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0095-92	Right Frontal Restraints Sensor - performance or incorrect operation	Performance or incorrect operation	Check component fixings for security. If secure suspect right hand Front Crash Sensor internal fault. Check and install a new Right Frontal Restraints sensor as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0095-96	Right Frontal Restraints Sensor - component internal failure	Right hand Front Crash Sensor failure	Check and install a new Right Frontal Restraints sensor as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0096-11	Right Side Restraints Sensor 1 - Circuit short to ground	Right hand Side Crash Sensor 1 circuit short circuit to ground	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (Door) circuit for short to ground
B0096-12	Right Side Restraints Sensor 1 - Circuit short to battery	Right hand Side Crash Sensor 1 circuit short circuit to power	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (Door) circuit for short to power
B0096-64	Right Side Restraints Sensor 1 - Signal plausibility failure	Right hand Side Crash Sensor 1 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0096-81	Right Side Restraints Sensor 1 - invalid serial data received	Right hand Side Crash Sensor 1 circuit open circuit Right Side Restraints Sensor 1 failure	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor circuit for open circuit fault. Check and install a new Right Side Restraints Sensor 1 (Door) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0096-92	Right Side Restraints Sensor 1 - performance or incorrect operation	Right hand Side Crash Sensor 1 component internal failure	Check and install a new Right Side Restraints Sensor 1 (Door) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0096-96	Right Side Restraints Sensor 1 - component internal failure	Right Side Crash Sensor 1 internal failure	Suspect right hand Side Crash Sensor (Door) internal fault. Check and install a new Right Side Restraints Sensor 1 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0097-11	Right Side Restraints Sensor 2 - Circuit short to ground	Right hand Side Crash Sensor 2 circuit short circuit to ground	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (B Pillar) circuit for short to ground
B0097-12	Right Side Restraints Sensor 2 - Circuit short to battery	Right hand Side Crash Sensor 2 circuit short circuit to power	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor (B Pillar) circuit for short to power
B0097-64	Right Side Restraints Sensor 2 - Signal plausibility failure	Right hand Side Crash Sensor 2 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0097-81	Right Side Restraints Sensor 2 - invalid serial data received	Right hand Side Crash Sensor 2 circuit open circuit Right Side Restraints Sensor 2 failure	Refer to the electrical circuit diagrams and check right hand Side Crash Sensor 2 (B Pillar) circuit for open circuit. Check and install a new right hand side Restraints Sensor 2 (B Pillar) as required
B0097-92	Right Side Restraints Sensor 2 - performance or incorrect operation	Right hand Side Restraints Sensor 2 component internal failure	Check component fixings for security. If secure suspect right hand Side Crash Sensor 2 (B Pillar) internal fault. Check and install a new right hand Side Crash Sensor 2 (B Pillar) as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0097-96	Right Side Restraints Sensor 2 - component internal failure	Right Side Restraints Sensor 2 component internal failure	Suspect right hand Side Crash Sensor (B Pillar) internal fault. Check and install a new Right Side Restraints Sensor 2 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0098-11	Right Side Restraints Sensor 3 - Circuit short to ground	Right hand Rear Side Crash Sensor 3 circuit short circuit to ground	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for short to ground
B0098-12	Right Side Restraints Sensor 3 - Circuit short to battery	Right hand Rear Side Crash Sensor 3 circuit short circuit to power	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for short to power
B0098-64	Right Side Restraints Sensor 3 - Signal plausibility failure	Right hand Rear Side Crash Sensor 3 configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B0098-81	Right Side Restraints Sensor 3 - invalid serial data received	Right hand Rear Side Crash Sensor 3 circuit - open circuit Right Side Restraints Sensor 3 failure	Refer to the electrical circuit diagrams and check right hand Rear Side Crash Sensor circuit for open circuit fault. Check and install a new Right Side Restraints Sensor 3 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0098-92	Right Side Restraints Sensor 3 - performance or incorrect operation	Right Side Restraints Sensor 3 component internal failure	Check and install a new Right Side Restraints Sensor 3 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B0098-96	Right Side Restraints Sensor 3 - component internal failure	Right hand Rear Side Restraints Sensor 3 internal failure	Suspect right hand Rear Side Crash Sensor internal fault. Check and install a new Right Rear Side Restraints Sensor 3 as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B00A0-49	Occupant Classification System - internal electronic failure	Occupant Classification System internal failure	Check and install a new Occupant Classification System module as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B00A0-64	Occupant Classification System - Signal plausibility failure	Occupant Classification System configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B00A0-88	Occupant Classification System - bus off	Occupant Classification System circuit, open circuit, high resistance	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network.
B00A0-92	Occupant Classification System - performance or incorrect operation	Occupant Classification System module circuit, short circuit to ground, short circuit to power, open circuit Occupant Classification System Module internal failure	Refer to the electrical circuit diagrams and check Occupant Classification System module circuit for short to ground, short to power, open circuit. Check and install a new Occupant Classification System module as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B00B5-11	Driver Seat Track Position Restraints Sensor - Circuit short to ground	Driver seat position sensor circuit short circuit to ground	Refer to the electrical circuit diagrams and check Driver Seat Position Sensor circuit for short to ground
B00B5-15	Driver Seat Track Position Restraints Sensor - Circuit short to battery or open	Driver seat position sensor circuit short circuit to power, open circuit	Refer to the electrical circuit diagrams and check Driver Seat Position Sensor circuit for short to power, open circuit
B00B5-1D	Driver Seat Track Position Restraints Sensor - Circuit current out of range	Circuit current out of range	Refer to the electrical circuit diagrams and check Driver Seat Position Sensor circuit for fault
B00B5-64	Driver Seat Track Position Restraints Sensor - Signal plausibility failure	Driver Seat Track Position Restraints Sensor configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B00C0-96	Passenger Seat Occupant Classification Sensor "A" - component internal failure	Passenger Seat Occupant Classification Sensor "A" internal failure	Check and install a new Passenger Seat Occupant Classification Sensor "A" as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B00D2-68	Restraint System Malfunction Indicator 1 - event information	Events information	Suspect Instrument Cluster Internal fault Check for stored DTCs
B00D2-87	Restraint System Malfunction Indicator 1 - missing message	Missing message from Instrument Cluster	Check CAN Bus circuit to Instrument Cluster for circuit fault
B00D5-12	Restraint System Passenger Disable Indicator - circuit short to battery	Passenger Airbag Disable (PAD) Lamp circuit short circuit to power	Refer to the electrical circuit diagrams and check PAD Lamp circuit for short to power (PAD Lamp located in the Integrated Control Panel)
B00D5-14	Restraint System Passenger Disable Indicator - Circuit short to ground or open	Passenger Airbag Disable (PAD) Lamp circuit short circuit to ground open circuit, high resistance	Refer to the electrical circuit diagrams and check PAD Lamp circuit for short to ground, open circuit, high resistance
B00D5-55	Restraint System Passenger Disable Indicator - not configured	Module Not Configured	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B00DF-00	Passenger Restraints Disable Switch - No sub type information	Passenger Restraints Disable Switch stuck Passenger Restraints Disable Switch internal failure	Check and install a new Passenger Restraints Disable Switch as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B00DF-54	Passenger Restraints Disable Switch - missing calibration	Passenger Airbag Disable Switch missing calibration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B00DF-64	Passenger Restraints Disable Switch - Signal plausibility failure	Passenger Restraints Disable Switch configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1211-11	Driver Seatbelt Retractor Pretensioner Deployment Control - Circuit short to ground	Driver seatbelt retractor pretensioner deployment control circuit short circuit to ground	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit short to ground
B1211-12	Driver Seatbelt Retractor Pretensioner Deployment Control - Circuit short to battery	Driver seatbelt retractor pretensioner deployment control circuit short circuit to power	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit short to power
B1211-1A	Driver Seatbelt Retractor Pretensioner Deployment Control - Circuit resistance below threshold	Driver seatbelt retractor pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit for circuit shorted to each other
B1211-1B	Driver Seatbelt Retractor Pretensioner Deployment Control - Circuit resistance above threshold	Driver seatbelt retractor pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit open circuit, high resistance
B1211-64	Driver Seatbelt Retractor Pretensioner Deployment Control - Signal plausibility failure	Driver seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1211-95	Driver Seatbelt Retractor Pretensioner Deployment Control - incorrect assembly	Driver seatbelt retractor pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check driver seatbelt retractor pretensioner deployment control circuit for faults
B1212-11	Driver Seatbelt Buckle Pretensioner Deployment Control - Circuit short to ground	Driver seatbelt buckle pretensioner deployment control circuit short circuit to ground	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit short to ground
B1212-12	Driver Seatbelt Buckle Pretensioner Deployment Control - Circuit short to battery	Driver seatbelt buckle pretensioner deployment control circuit short circuit to power	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit short to power
B1212-1A	Driver Seatbelt Buckle Pretensioner Deployment Control - Circuit resistance below threshold	Driver seatbelt buckle pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit for circuit shorted to each other
B1212-1B	Driver Seatbelt Buckle Pretensioner Deployment Control - Circuit resistance above threshold	Driver seatbelt buckle pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit open circuit, high resistance
B1212-64	Driver Seatbelt Buckle Pretensioner Deployment Control - Signal plausibility failure	Driver seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1212-95	Driver Seatbelt Buckle Pretensioner Deployment Control - incorrect assembly	Driver seatbelt buckle pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check driver seatbelt buckle pretensioner deployment control circuit for faults
B1213-11	Passenger Seatbelt Buckle Pretensioner Deployment Control - Circuit short to ground	Passenger seatbelt buckle pretensioner deployment control circuit short circuit to ground	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit short to ground
B1213-12	Passenger Seatbelt Buckle Pretensioner Deployment Control - Circuit short to battery	Passenger seatbelt buckle pretensioner deployment control circuit short circuit to power	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit short to power
B1213-1A	Passenger Seatbelt Buckle Pretensioner Deployment Control - Circuit resistance below threshold	Passenger seatbelt buckle pretensioner deployment control circuit resistance below threshold	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit for circuit shorted to each other
B1213-1B	Passenger Seatbelt Buckle Pretensioner Deployment Control - Circuit resistance above threshold	Passenger seatbelt buckle pretensioner deployment control circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit open circuit, high resistance
B1213-64	Passenger Seatbelt Buckle Pretensioner Deployment Control - Signal plausibility failure	Passenger seatbelt retractor pretensioner deployment control configuration error	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1213-95	Passenger Seatbelt Buckle Pretensioner Deployment Control - incorrect assembly	Passenger seatbelt buckle pretensioner deployment control short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and check passenger seatbelt buckle pretensioner deployment control circuit for faults
B1A00-16	Control Module - Circuit voltage below threshold	Charging system fault Vehicle battery fault Restraints Control Module failure	Refer to repair information and battery care information, check vehicle battery and charging system. Perform any repairs required. Check and install a new Restraints Control Module as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B1A00-17	Control Module - Circuit voltage above threshold	Charging system over charging fault Restraints Control Module failure	Check vehicle battery and charging system. Perform any repairs required. Check and install a new Restraints Control Module as required. Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
B1A00-49	Control Module - internal electronic failure	Internal electronic failure	Restraint Control Module internal fault, refer to the new module installation note at the top of the DTC index
B1A17-95	Driver Stage 1 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Driver Airbag Squib (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Driver Airbag Squib (Stage 1) circuit for faults
B1A19-95	Driver Stage 2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Driver Airbag Squib (Stage 2) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Driver Airbag Squib (Stage 2) circuit for faults
B1A21-95	Passenger Stage 1 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Passenger Airbag Squib (Stage 1) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Passenger Airbag Squib (Stage 1) circuit for faults
B1A23-95	Passenger Stage 2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Passenger Airbag Squib (Stage 2) Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Passenger Airbag Squib (Stage 2) circuit for faults
B1A29-95	Left Side Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Left Side Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Left Side Airbag Squib circuit for faults
B1A31-95	Right Side Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Right Side Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Right Side Airbag Squib circuit for faults
B1A33-95	Left Curtain Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Left Curtain Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Left Curtain Airbag Squib circuit for faults
B1A35-95	Right Curtain Airbag Squib Short Circuit To Ignition Loop - Incorrect Assembly	Right Curtain Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Right Curtain Airbag Squib circuit for faults
B1A37-95	Left Curtain #2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Left Curtain #2 Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Left Curtain #2 Airbag Squib circuit for faults
B1A39-95	Right Curtain #2 Airbag Squib Short Circuit To Ignition Loop - incorrect assembly	Right Curtain #2 Airbag Squib Incorrect assembly. Short circuit between two different circuits (at least two faults)	Refer to electrical circuit diagrams and test Right Curtain #2 Airbag Squib circuit for faults
B1A40-11	Left Side (pelvic) 2 - circuit short to ground	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A40-12	Left Side (pelvic) 2 - circuit short to battery	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A40-1A	Left Side (pelvic) 2 - circuit resistance below threshold	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A40-1B	Left Side (pelvic) 2 - circuit resistance above threshold	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A40-64	Left Side (pelvic) 2 - signal plausibility failure	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A40-95	Left Side (pelvic) 2 - incorrect assembly	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A41-95	Left Side (pelvic) 2 Short circuit To Ignition Loop - incorrect assembly	Left Side (pelvic) 2 incorrect assembly. Short circuit between two different circuits (at least two faults)	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1A55-14	Crash Record Output - Circuit short to ground or open	Crash Record Output circuit short circuit to ground or open	Refer to the electrical circuit diagrams and check Crash Record Output circuit for short to ground or open circuit. If this has occurred after a software download then disconnect the battery for 1 minute
B1A55-64	Crash Record Output - Signal plausibility failure	Signal plausibility failure	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-11	Right Side (pelvic) 2 - circuit short to ground	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-12	Right Side (pelvic) 2 - circuit short to battery	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-1A	Right Side (pelvic) 2 - circuit resistance below threshold	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-1B	Right Side (pelvic) 2 - circuit resistance above threshold	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-64	Right Side (pelvic) 2 - signal plausibility failure	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D60-95	Right Side (pelvic) 2 - incorrect assembly	Only logged in the event of incorrect module configuration	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system
B1D74-11	Passenger Airbag Cutoff Enable Switch - Circuit short to ground	Passenger Airbag Enable Switch circuit short circuit to ground	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for short to ground
B1D74-12	Passenger Airbag Cutoff Enable Switch - Circuit short to battery	Passenger Airbag Enable Switch circuit short circuit to power	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for short to power
B1D74-13	Passenger Airbag Cutoff Enable Switch - Circuit open	Passenger Airbag Enable Switch circuit open circuit, high resistance	Refer to the electrical circuit diagrams and check Passenger Airbag Enable Switch circuit for open circuit, high resistance
B1D75-11	Passenger Airbag Cutoff Disable Switch - Circuit short to ground	Passenger Airbag Disable Switch circuit short circuit to ground	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for short to ground
B1D75-12	Passenger Airbag Cutoff Disable Switch - Circuit short to battery	Passenger Airbag Disable Switch circuit short circuit to power	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for short to power
B1D75-13	Passenger Airbag Cutoff Disable Switch - Circuit open	Passenger Airbag Disable Switch open circuit, high resistance	Refer to the electrical circuit diagrams and check Passenger Airbag Disable Switch circuit for open circuit, high resistance
U0001-88	High Speed CAN Communication Bus - bus off	Bus off	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network
U0122-87	Lost Communication With Vehicle Dynamics Control Module - missing message	Lost Communication With Vehicle Dynamics Control Module	Refer to the electrical circuit diagrams and check the power and ground connections to the module. Using the manufacturer approved diagnostic system, complete a CAN network integrity test. Refer to the electrical circuit diagrams and check the CAN network between the Restraints Control Module and Vehicle Dynamics Control Module
U0300-55	Internal Control Module Software Incompatibility - not configured	Mis-match between vehicle and Restraints Control Module software levels	Re-configure the Restraints Control Module with the correct level software using the manufacturer approved diagnostic system
U1A02-66	Permanent Memory Store Full - signal has too many transitions / events	Wiring harness fault Restraint Control Module internal fault	Restraint Control Module memory full - refer to the new module installation note at the top of the DTC index (Not warrantable change)
U1A03-87	Car Configuration Parameter - missing message	Missing message	Lost communication with Body control module. Check Body control module for stored DTCs. Refer to the electrical circuit diagrams and check, CAN Bus circuit to Body Control Module for fault
U1A14-55	CAN Initialization Failure - not configured	Restraints Control Module not configured	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-check, if DTC remains Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U201A-4A	Control module Main Calibration Data - incorrect component installed	Incorrect component installed	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Restraints Control Module internal fault, refer to the new module installation note at the top of the DTC index
U201A-51	Control Module Main Calibration Data - not programmed	Restraints Control Module not programmed	Re-configure the Restraints Control Module with the correct level software using the manufacturer approved diagnostic system
U201B-4A	Control Module Calibration Data #2 - incorrect component Check and installed	Incorrect Restraints Control Module Check and installed	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-check, if DTC remains Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U201B-51	Control Module Calibration Data #2 - not programmed	Restraints Control Module not programmed	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-check, if DTC remains Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U201C-4A	Control Module Calibration Data #3 - incorrect component Check and installed	Incorrect Restraints Control Module Check and installed	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-check, if DTC remains Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U201C-51	Control Module Calibration Data #3 - not programmed	Restraints Control Module not programmed	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-check, if DTC remains Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U3000-49	Control Module - internal electronic failure	Restraints Control Module internal electronic failure	Suspect Restraints Control Module internal fault, Refer to the Warranty Policy and Procedures information, or determine if any prior approval program is in operation, prior to the installation of a new module/component
U3002-81	Vehicle Identification Number - invalid serial data received	Vehicle/component mis-match Corrupt VIN data being transmitted Module previously installed to other vehicle	Re-configure the Restraints Control Module using the manufacturer approved diagnostic system. Clear DTC and re-test, if DTC remains Restraints Control Module internal fault, refer to the new module installation note at the top of the DTC index