LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2006 >> LS 430 >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control System - Diagnostics >> Data List/Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List/Active Test

  1. DATA LIST 
    1. While the hand-held tester is connected to the DLC3 and with the ignition switch turned to the ON position, the CRUISE CONTROL data list can be displayed. Follow the prompts on the tester screen to access the data list.
    DATA LIST (CC (ECM))

    Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
    VEHICLE SPD Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
    MEMORY SPD Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual stored vehicle speed -
    THROTTLE Required throttle opening angle / min.: 0°, max.: 125° Actual required throttle opening -
    CRUISE CTRL Cruise control system active condition / ON or OFF ON: Cruise control activated OFF: Cruise control inactivated -
    MAIN SW (MAIN) Main SW signal (Main CPU) / ON or OFF ON: Main SW ON (Pushed on) OFF: Main SW OFF (Pushed off) "3"
    MAIN SW (SUB) Main SW signal (Sub CPU) / ON or OFF ON: Main SW ON (Pushed on) OFF: Main SW OFF (Pushed off) "3"
    CCS READY M Cruise control system standby condition (Main CPU) / ON or OFF ON --> OFF: Change ON/OFF each time Main SW is pushed in. "1"
    CCS READY S Cruise control system standby condition (Sub CPU) / ON or OFF ON --> OFF: Change ON/OFF each time Main SW is pushed in. "1"
    CCS INDICATOR M Cruise indicator signal (Main CPU) /ON or OFF ON: "CCS READY" ON OFF: "CCS READY" OFF "2"
    CCS INDICATORS Cruise indicator signal (Sub CPU) /ON or OFF ON: "CCS READY" ON OFF: "CCS READY" OFF "2"
    CANCEL SW CANCEL SW signal / ON or OFF ON: CANCEL SW ON OFF: CANCEL SW OFF -
    SET/COAST SW SET/COAST SW signal / ON or OFF ON: SET/COAST SW ON OFF: SET/COAST SW OFF -
    RES/ACC SW RES/ACC SW signal / ON or OFF ON: RES/ACC SW ON OFF: RES/ACC SW OFF -
    STP LIGHT SW M Stop lamp SW signal (Main CPU) / ON or OFF ON: Brake pedal depressed OFF: Brake pedal released -
    STP LIGHT SW S1 Stop lamp SW signal (Sub CPU) / ON or OFF ON: Brake pedal depressed OFF: Brake pedal released -
    STP LIGHT SW S2 Stop light SW signal (Sub CPU) / ON or OFF ON: Brake pedal depressed OFF: Brake pedal released -
    SHIFT D POS PNP SW signal (D position) / ON or OFF ON: Shift D position OFF: Except shift D position -

    HINT:

    "3" is OK but "1" is NG --> ECM failure

    "1" is OK but "2" is NG --> DTC output or ECM failure

    "3" is OK but cruise indicator not turn on --> CRUISE MAIN indicator or wire harness or ECM failure

  2. ACTIVE TEST 

    HINT:

    Performing the ACTIVE TEST using the hand-held tester allows components such as the relay, VSV, and actuator to operate without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten labor time.

    It is possible to display the DATA LIST during the ACTIVE TEST.

    1. Connect the hand-held tester to the DLC3.
    2. Turn the ignition switch to the ON position.
    3. According to the display on the tester, perform the "ACTIVE TEST".

    HINT:

    The ignition switch must be turned to the ON position to proceed ACTIVE TEST using the hand-held tester.

    ACTIVE TEST DETAIL (COMBINATION METER ASSY)

    Item Vehicle Condition / Test Details Diagnostic Note
    CRUISE INDIC "CRUISE" indicator is ON / OFF -
scientia non olet · About LEMON Manuals