Torque Specification
WARNING: This page is about a different car, the 2006 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
1GR-FE:
TIGHTENING TORQUE SPECIFICATION (ENGINE MECHANICAL-1GR-FE)
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Engine under cover sub-assy No.1 x Frame assy | 29 | 296 | 21 | |
| Camshaft bearing cap x Cylinder head sub-assy | 10 mm (0.39 in.) head | 9.0 | 92 | 80 in..lbf |
| - | 12 mm (0.47 in.) head | 24 | 245 | 18 |
| Chain tensioner No.1 x Cylinder head sub-assy | 10 | 102 | 7 | |
| Chain tensioner No.2 x Cylinder head sub-assy | 19 | 194 | 14 | |
| Chain tensioner No.3 x Cylinder head sub-assy | 19 | 194 | 14 | |
| Camshaft timing gear assy x Camshaft | 100 | 1,020 | 74 | |
| Camshaft timing gear or sprocket x Camshaft | 100 | 1,020 | 74 | |
| Timing chain cover plate x Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Ignition coil assy x Cylinder head cover sub-assy | 10 | 102 | 7 | |
| V-bank cover sub-assy x Intake air surge tank | 7.5 | 76 | 66 in..lbf | |
| Engine hanger No.1 x Cylinder head sub-assy RH | 33 | 336 | 24 | |
| Engine hanger No.2 x Cylinder head sub-assy LH | 33 | 336 | 24 | |
| Spark plug x Cylinder head sub-assy | 20 | 204 | 15 | |
| Oil filler cap housing x Cylinder head cover sub-assy LH | 9.0 | 92 | 80 in..lbf | |
| Camshaft timing oil control valve assy x Cylinder head cover sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil filter bracket sub-assy x Timing chain or belt cover sub-assy | 19 | 194 | 14 | |
| Engine mounting bracket front No.1 RH x Cylinder block sub-assy | 43 | 435 | 31 | |
| Engine mounting bracket front No.1 LH x Cylinder block sub-assy | 43 | 435 | 31 | |
| Engine mounting insulator front No.1 RH x Frame assy | 38 | 387 | 28 | |
| Engine mounting insulator front No.1 LH x Frame assy | 38 | 387 | 28 | |
| Engine wire No.2 (ground cable) x Cylinder block sub-assy | 13 | 133 | 9 | |
| Hood sub-assy x Hood hinge assy RH & LH | 13 | 133 | 10 | |
| Hood support RH & LH x Body | 18 | 184 | 13 | |
| Engine rear oil seal retainer x Cylinder block sub-assy | Nut | 9.0 | 92 | 80 in..lbf |
| - | Bolt | 10 | 102 | 7 |
| Knock sensor x Cylinder block sub-assy | 20 | 204 | 15 | |
| Water outlet pipe No.1 x Cylinder block sub-assy | 10 | 102 | 7 | |
| Cylinder head sub-assy RH x Cylinder block sub-assy | 1st | 36 | 367 | 27 |
| - | 2nd | Turn 180° | Turn 180° | Turn 180° |
| Cylinder head sub-assy LH x Cylinder block sub-assy | - | - | - | |
| - | Recessed head 1st | 36 | 367 | 27 |
| - | 2nd | Turn 180° | Turn 180° | Turn 180° |
| - | 14 mm (0.55 in.) head | 30 | 306 | 22 |
| Chain vibration damper No.1 x Cylinder block sub-assy | 19 | 194 | 14 | |
| Idle gear No.1 x Cylinder block sub-assy | 60 | 612 | 44 | |
| Timing chain or belt cover sub-assy x Cylinder head and block | 23 | 235 | 17 | |
| Water pump assy x Timing chain or belt cover sub-assy | - | - | - | |
| - | 10 mm (0.39 in.) head | 9.0 | 92 | 80 in..lbf |
| - | 12 mm (0.47 in.) head | 23 | 235 | 17 |
| Oil pan stud bolt x Oil pan sub-assy | 4.0 | 41 | 35 in..lbf | |
| Oil pan sub-assy x Cylinder block and timing chain or belt cover | - | - | - | |
| - | Bolt A | 21 | 214 | 15 |
| - | Bolt B | 21 | 214 | 15 |
| - | Bolt C | 10 | 102 | 7 |
| - | Nut | 21 | 214 | 15 |
| Oil strainer sub-assy x Oil pan sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan sub-assy No.2 x Oil pan sub-assy | Bolt | 9.0 | 92 | 80 in..lbf |
| - | Nut | 10 | 102 | 7 |
| Oil pan drain plug x Oil pan sub-assy No.2 | 40 | 408 | 30 | |
| Crankshaft pulley x Crankshaft | 250 | 2,549 | 184 | |
| Cylinder head cover sub-assy x Cylinder head sub-assy RH | Bolt A | 10 | 102 | 7 |
| - | Bolt B | 9.0 | 92 | 80 in..lbf |
| - | Nut | 9.0 | 92 | 80 in..lbf |
| Cylinder head cover sub-assy LH x Cylinder head sub-assy LH | Bolt A | 10 | 102 | 7 |
| - | Bolt B | 9.0 | 92 | 80 in..lbf |
| - | Nut | 9.0 | 92 | 80 in..lbf |
| Ventilation valve x Cylinder head cover sub-assy LH | 27 | 275 | 20 | |
| Oil control valve filter plug x Cylinder head sub-assy | 62 | 632 | 46 | |
| Crankshaft position sensor x Cylinder block sub-assy | 10 | 102 | 7 | |
| VVT sensor x Timing chain or belt cover sub-assy | 8.0 | 82 | 71 in..lbf | |
| Cylinder block water drain cock sub-assy x Cylinder block sub-assy | 25 | 255 | 18 | |
| Oil level gauge guide x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan sub-assy x Transmission | 37 | 377 | 27 | |
| Idler pulley sub-assy No.1 x Timing chain or belt cover sub-assy | 54 | 551 | 40 | |
| Idler pulley sub-assy No.2 x Timing chain or belt cover sub-assy | 39 | 398 | 29 | |
| V-ribbed belt tensioner assy x Cylinder block sub-assy | 36 | 367 | 27 | |
| Vane pump assy x Cylinder block sub-assy | 43 | 438 | 32 | |
| Intake air surge tank x Intake manifold | 26 | 265 | 19 | |
| Surge tank stay x Intake air surge tank and cylinder head | 21 | 214 | 15 | |
| Throttle body bracket x Throttle body w/ motor and cylinder head | 21 | 214 | 15 | |
| Oil baffle plate x Surge tank stay No.1 | 9.0 | 92 | 80 in..lbf | |
| Ground cable x Cylinder head sub-assy | 8.0 | 82 | 71 in..lbf | |
| Water by-pass joint RR x Cylinder head sub-assy | 9.0 | 92 | 80 in..lbf | |
| Intake manifold x Cylinder head sub-assy | 26 | 265 | 19 | |
| Exhaust manifold sub-assy RH x Cylinder head sub-assy RH | 30 | 306 | 22 | |
| Exhaust manifold sub-assy LH x Cylinder head sub-assy LH | 30 | 306 | 22 | |
| Manifold stay x Exhaust manifold sub-assy RH and transmission | 40 | 408 | 30 | |
| Manifold stay No.2 x Exhaust manifold sub-assy LH and transmission | 40 | 408 | 30 | |
| Transmission oil filler tube sub-assy x Cylinder head sub-assy | 12 | 122 | 9 | |
| Cool air inlet No.1 x Body | 12 | 122 | 9 | |
| Drive plate & ring gear sub-assy x Crankshaft | 83 | 846 | 61 | |
| Stud bolt x Cylinder head sub-assy and cylinder head LH | - | - | - | |
| (See OVERHAUL ) | A | 4.0 | 41 | 35 in..lbf |
| - | B | 9.0 | 92 | 80 in..lbf |
| Union x Cylinder head sub-assy and cylinder head LH | 15 | 150 | 11 | |
| W/ Head taper screw plug x Cylinder head sub-assy and cylinder head LH | 80 | 816 | 59 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| - | 2nd | Turn 90° | Turn 90° | Turn 90° |
| Main bearing cap x Cylinder block sub-assy | 12 pointed head 1st | 61 | 622 | 45 |
| - | 2nd | Turn 90° | Turn 90° | Turn 90° |
| - | 12 mm head | 26 | 262 | 19 |
| Stud bolt x Cylinder block sub-assy (See OVERHAUL ) | A | 11 | 112 | 8.1 |
| - | B | 4.5 | 46 | 40 in..lbf |
| - | C | 4.0 | 41 | 35 in..lbf |
| Sub-assy oil nozzle No.1 x Cylinder block sub-assy | 9.0 | 92 | 80 in..lbf | |
2UZ-FE:
TIGHTENING TORQUE SPECIFICATION (ENGINE MECHANICAL-2UZ-FE)
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Oil pan sub-assy No.2 x Drain plug | 39 | 398 | 29 | |
| Cylinder head cover sub-assy LH x Ventilation valve sub-assy | 27 | 275 | 20 | |
| Oil pump assy x Oil cooler assy | Bolt | 18 | 183 | 13 |
| - | Nut | 18 | 183 | 13 |
| Water by-pass joint FR x Cylinder head | 18 | 185 | 13 | |
| Water by-pass pipe x Cylinder block | 18 | 185 | 13 | |
| Starter assy x Cylinder block | 39 | 400 | 29 | |
| Starter assy x Engine wire No. 2 | 9.8 | 100 | 7.2 | |
| Water by-pass joint RR x Cylinder head | 18 | 185 | 13 | |
| Knock sensor x Cylinder block | 45 | 450 | 33 | |
| Crankshaft position sensor x Oil pump assy | 6.5 | 65 | 58 in..lbf | |
| Camshaft position sensor x Cylinder head | 7.5 | 80 | 66 in..lbf | |
| Ignition coil assy x Cylinder head cover | 7.5 | 80 | 66 in..lbf | |
| Fan bracket sub-assy x Cylinder block | 12 mm head | 16 | 160 | 12 |
| - | 14 mm head | 16 | 160 | 12 |
| V-ribbed belt tensioner assy x Cylinder block | Bolt | 16 | 160 | 12 |
| - | Nut | 16 | 160 | 12 |
| Timing belt cover sub-assy No.2 x Cylinder block | 16 | 160 | 12 | |
| Timing chain or belt cover No.2 x Cylinder block | Bolt | 7.5 | 80 | 66 in..lbf |
| - | Nut | 7.5 | 80 | 66 in..lbf |
| Timing belt cover sub-assy No.3 LH x Cylinder block | 7.5 | 80 | 66 in..lbf | |
| Pump bracket x Cylinder block | 43 | 438 | 32 | |
| Oil cooler pipe x Cylinder block | Bolt | 7.5 | 80 | 66 in..lbf |
| - | Nut | 7.5 | 80 | 66 in..lbf |
| Harness bracket x Cylinder block | 8.0 | 80 | 71 in..lbf | |
| Engine mounting bracket x Cylinder block | 36 | 367 | 27 | |
| Wire harness heat insulator No.2 x Cylinder block | 17 | 175 | 13 | |
| Intake manifold assy x Cylinder head | 18 | 185 | 13 | |
| Engine mounting bracket x Frame brackets | 38 | 387 | 28 | |
| Exhaust manifold x Cylinder head | 44 | 450 | 33 | |
| Exhaust manifold heat insulator x Exhaust manifold | 7.5 | 80 | 69 in..lbf | |
| Oil level gauge guide x Cylinder head | 15 | 155 | 11 | |
| Transmission oil filler tube x Cylinder head | 12 | 122 | 9 | |
| Fan w/ fluid coupling x Fan bracket sub-assy | 29 | 296 | 21 | |
| Compressor x Cylinder block | Bolt | 47 | 475 | 34 |
| - | Nut | 25 | 255 | 18 |
| Vane pump assy x Cylinder block | Bolt | 43 | 438 | 32 |
| - | Nut | 43 | 438 | 32 |
| Fan shroud x Radiator assy | 5.0 | 51 | 44 in..lbf | |
| Air cleaner assy x Body | 12 | 122 | 9 | |
| Throttle body cover x Intake manifold assy | 7.5 | 80 | 66 in..lbf | |
| Hood x Body | 13 | 133 | 10 | |
| Engine rear oil seal retainer x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil pump assy x Cylinder block | Bolt A, B, C and E | 16 | 158 | 11 |
| - | Bolt D | 31 | 311 | 23 |
| Oil strainer sub-assy x Cylinder block | 7.5 | 76 | 66 in..lbf | |
| Oil pan sub-assy x Cylinder block | Bolt A and D | 7.5 | 76 | 66 in..lbf |
| - | Bolt B, C and nut | 28 | 286 | 21 |
| Oil pan baffle plate x Oil pan sub-assy | 7.5 | 76 | 66 in..lbf | |
| Oil pan sub-assy No.2 x Oil pan sub-assy | 7.5 | 76 | 66 in..lbf | |
| Water pump assy x Cylinder block | Bolt | 21 | 214 | 15 |
| - | Stud bolt and nut | 18 | 184 | 13 |
| Cylinder head x Cylinder block | 1st | 40 | 408 | 30 |
| - | 2nd | Turn 90 | Turn 90 | Turn 90 |
| - | 3rd | Turn 90 | Turn 90 | Turn 90 |
| Bearing cap x Cylinder head | Bolt C | 7.5 | 76 | 66 in..lbf |
| - | Other | 16 | 163 | 12 |
| Timing belt plate RR x Cylinder head | 7.5 | 76 | 66 in..lbf | |
| Timing belt idler sub-assy No.2 x Cylinder block | 35 | 352 | 25 | |
| Timing belt idler sub-assy No.1 x Cylinder block | 35 | 352 | 25 | |
| Camshaft timing pulley x Camshaft | 108 | 1101 | 80 | |
| Chain tensioner assy x Oil pump assy | 26 | 270 | 19 | |
| Timing belt No.1 over x Cylinder block | 7.5 | 76 | 66 in..lbf | |
| Crankshaft damper x Crankshaft | 245 | 2498 | 181 | |
| Idler pulley sub-assy No.2 | 39 | 398 | 29 | |
| Oil filler cap housing x Cylinder head cover | 7.5 | 76 | 66 in..lbf | |
| Spark plug x Cylinder head | 17.5 | 178 | 13 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| - | 2nd | Turn 90 | Turn 90 | Turn 90 |
| Main bearing cap x Cylinder block | 1st | 27 | 275 | 20 |
| - | 2nd | Turn 90 | Turn 90 | Turn 90 |
| Cylinder head cover x Cylinder head | 6.0 | 60 | 53 in..lbf | |
| Drive plate & ring gear x Crankshaft | 1st | 49 | 500 | 36 |
| - | 2nd | Turn 90 | Turn 90 | Turn 90 |
| Camshaft drive gear x Camshaft timing tube assy | 7.5 | 76 | 66 in..lbf | |
| Camshaft timing tube assy x Camshaft | 78 | 795 | 58 | |
| Screw plug x Camshaft timing tube assy | 15 | 152 | 11 | |
| Timing belt plate RR x Cylinder head | 7.5 | 76 | 66 in..lbf | |