Data List / Active Test

HINT:

Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

1. Connect the intelligent tester (with CAN VIM) to the DLC3.
2. Turn the power switch ON (IG).
3. Read the DATA LIST according to the display on the tester.

   Hybrid vehicle control ECU 

   ITEM MEASUREMENT CONDITIONS
   
   

   Item	Measurement Item / Display (Range)	Normal Condition
   ACCEL REQUEST	Accelerator request signal / min.: -2621.44 k/h/s, max.: 2621.36 k/ h/s	No vehicle in front
   VEHICLE DISTANC	Millimeter wave radar sensor / min.: 0 m (0 ft), max.: 255 m (836.65 ft)	Distance to vehicle in front
   L/C OPTION FLAG	Dynamic radar cruise option flag / NO or YES	YES: Vehicle-to-vehicle distance mode
   DISTANCE TIME	Vehicle distance time setting condition / SHRT, MID, LONG, NO	Vehicle distance selected by steering pad switch (distance control switch)
   O/D CUT RQST	O/D cut request / NOT REQ or REQUEST	NOT REQ: Idling
   3RD SHIFT DOWN	Shift down request to 3rd gear / NOT REQ or REQUEST	NOT REQ: Idling
   4TH SHIFT DOWN	Shift down request to 4th gear / NOT REQ or REQUEST	NOT REQ: Idling
   ALARM RQST	Warning buzzer request signal / NOT REQ or REQUEST	REQUEST: Buzzer sounds NOT REQ: Buzzer does not sounds
   THROTTLE CLOSE	All throttle close request / NOT REQ or REQUEST	REQUEST: ON NOT REQ: OFF
   BRAKE CTRL RQST	Brake control request / NOT REQ or REQUEST	REQUEST: ON NOT REQ: OFF
   TARG DECL SLOPE	Cruise target deceleration slope / 0.03,0.06,0.11,0.16	0.03,0.06,0.11,0.16
   VEHICLE SPD	Vehicle speed sensor/ min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed
   MEMORY SPD	Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Memorized speed: Cruise control activated
   RQST TORQUE	Cruise request torque / min.: -1,024 N*m (-1,0442 kgf*cm, -755 ft.*lbf), max.: 1,016 N*m (10,360 kgf*cm, 749 ft.*lbf)	-
   CRUISE CONTROL	Cruise control system active condition / ON or OFF	ON: Cruise control activated OFF: Cruise control inactivated
   CCS MAIN SW M-CPU	Main switch signal (Main CPU) / ON or OFF	ON: Main switch ON (Pushed on) OFF: Main switch OFF (Pushed off)
   CCS READY M-CPU	Cruise control system standby condition (Main CPU) / ON or OFF	Each time main switch is pushed, ON is displayed and then OFF is displayed
   CCS INDICATOR M-CPU	Cruise indicator signal (Main CPU) / ON or OFF	ON: "CCS READY" ON OFF: "CCS READY" OFF
   CANCEL SW	CANCEL switch signal / ON or OFF	ON: CANCEL switch ON OFF: CANCEL switch OFF
   SET/COAST SW	SET/COAST switch signal / ON or OFF	ON: SET / COAST switch ON OFF: SET / COAST switch OFF
   RES/ACC SW	RES/ACC switch signal / ON or OFF	ON: RES/ACC switch ON OFF: RES / ACC switch OFF
   STP LIGHT SW M-CPU	Stop light switch signal (Main CPU)/ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released

HINT:

Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.

The DATA LIST can be displayed during the ACTIVE TEST.

1. Connect the intelligent tester (with CAN VIM) to the DLC3.
2. Turn the power switch ON (IG).
3. Perform the ACTIVE TEST according to the display on the tester.

   Combination meter 

   ITEM REFERENCE CHART
   
   

   Item	Test Details
   CRUISE INDIC	CRUISE main indicator light is ON / OFF