LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2008 >> GS 350 AWD >> Repair and Diagnosis >> Accessories & Equipment >> Cruise Control Systems >> Cruise Control >> Dynamic Radar Cruise Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

  1. READ DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Radar Cruise / Data List.
    5. Read the Data List according to the display on the Techstream.

      ECM (Radar Cruise): 

      MEASUREMENT ITEM/RANGE CHART

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Accel Request Accelerator request signal / min.: -2621.44 k/h/s, max.: 2621.36 k/h/s Actual demanded acceleration request -
      Vehicle Distanc Millimeter wave radar sensor / min.: 0 m (0 ft.), max.: 255 m (836.65 ft.) Distance to the vehicle in front -
      L/C Option Flag Dynamic radar cruise option flag / NO or YES YES: Vehicle-to-vehicle distance mode -
      Distance Time Vehicle distance time setting condition / SHRT, MID, LONG, NO Vehicle distance selected by steering pad switch (distance control switch) -
      O/D Cut Rqst O/D cut request / NOT REQ or REQUEST NOT REQ: Idling -
      3rd Shift Down Shift down request to 3rd gear / NOT REQ or REQUEST NOT REQ: Idling -
      4th Shift Down Shift down request to 4th gear / NOT REQ or REQUEST NOT REQ: Idling -
      5th Shift Down Shift down request to 5th gear / NOT REQ or REQUEST NOT REQ: Idling -
      6th Shift Down Shift down request to 6th gear / NOT REQ or REQUEST NOT REQ: Idling -
      Alarm Rqst Alarm request signal / NOT REQ or REQUEST REQUEST: When beeping
      NOT REQ: When not beeping      		 -
      Throttle Close All throttle close request / NOT REQ or REQUEST ON: REQUEST
      OFF: NOT REQUEST      		 -
      Brake Ctrl Rqst Brake control request / NOT REQ or REQUEST ON: REQUEST
      OFF: NOT REQUEST      		 -
      Targ Decl Slope Cruise target deceleration slope / 0, 1, 2, 3 0, 1, 2, 3 -
      Vehicle Spd Vehicle speed sensor/ min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed -
      Memory Spd Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Memorized speed: Cruise control activated -
      Throttle Throttle opening angle: min.: 0°/ max.: 125° Actual demanded throttle angle for 1UR-FSE
      Rqst Torque Cruise request torque / min.: -1024 N*m (-10442 kgf*cm, -755 ft.*lbf), max.: 1016 N*m (10360 kgf*cm, 749 ft.*lbf) Actual required torque for 2GR-FSE
      Cruise Control Cruise control system active condition / ON or OFF ON: Cruise control activated
      OFF: Cruise control inactivated      		 -
      Main SW (Main) Main switch signal (Main CPU) / ON or OFF ON: Main switch ON (pushed on)
      OFF: Main switch OFF (pushed off)      		 A
      CCS Ready M Cruise control system standby condition (Main CPU) / ON or OFF Each time main switch is pushed, ON is displayed and then OFF is displayed B
      CCS Indicator M CRUISE main indicator signal (Main CPU) / ON or OFF ON: "CCS READY" ON
      OFF: "CCS READY" OFF      		 C
      Cancel SW CANCEL switch signal / ON or OFF ON: CANCEL switch ON
      OFF: CANCEL switch OFF      		 -
      SET/COAST SW SET / COAST switch signal / ON or OFF ON: SET / COAST switch ON
      OFF: SET / COAST switch OFF      		 -
      RES/ACC SW RES / ACC switch signal / ON or OFF ON: RES / ACC switch ON
      OFF: RES / ACC switch OFF      		 -
      Stp Light SW M Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released      		 -
      CCS Oper Status PNP switch signal (D position) / ON or OFF ON: Shift lever in D
      OFF: Shift lever not in D      		 -
      VSC Fail Safe VSC fail-safe flag / ON or OFF VSC communication fail safe in operation -
      # Codes Number of DTC recorded / 0 to 255 min.: 0
      max.: 21      		 -

      HINT:

      • A is OK, but B is NG → ECM failure
      • B is OK, but C is NG → DTC output or ECM failure
      • A is OK, but CRUISE main indicator light does not illuminate → Cruise main indicator light, wire harness, or ECM failure
  2. ACTIVE TEST 

    HINT:

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
    5. Perform Active Test according to the display on the Techstream.

      HINT:

      The engine switch must be turned on (IG) to proceed to the Active Test using the Techstream.

      Combination Meter (Meter ECU): 

      TESTER DISPLAY REFERENCE CHART

      Tester Display Test Part Control Range Diagnostic Note
      Indicat. Lamp Cruise CRUISE main indicator light ON / OFF -
scientia non olet · About LEMON Manuals