Shift Lever Position Sensor: Installation

INSTALL PARK/NEUTRAL POSITION SWITCH
1. Install the park/neutral position switch to the hybrid vehicle transmission assembly
2. Temporarily install the 2 bolts.
  HINT.
  
  Fully tighten the bolts with the neutral alignment mark line aligned with the groove. [*1]
  
  Fig 1: Locating Park/Neutral Position Switch Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install a new lock washer and the nut.
  Torque: 6.9 N*m (70 Kgf*cm, 61 in.*lbf)
  
  Fig 2: Locating Lock Washer And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Temporarily install the control shaft lever with the nut
  HINT.
  
  Bend the tabs of the lock washer before fully tightening the nut [*2]
  
  Fig 3: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Turn the control shaft lever counterclockwise until it stops Next, turn the control shaft lever clockwise 2 notches to set it to the N position
  
  Fig 4: Turning Control Shaft Lever Counterclockwise
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the nut and transmission control shaft lever
  
  Fig 5: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Align the neutral alignment mark line with the switch groove, and tighten the 2 adjusting bolts. [*1]
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
  
  Fig 6: Locating Adjusting Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. Using a screwdriver, bend the tabs of the lock washer.
  NOTE: Make sure that the nut is held firmly.
  
  Fig 7: Bending Tabs Of Lock Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. Install the transmission control shaft lever with the nut [*2]
  Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
  
  Fig 8: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. Connect the park/neutral position switch connector.
  
  Fig 9: Locating Park/Neutral Position Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
1. Move the shift lever to the N position and tighten the nut while lightly pushing the lever toward the R position
  Torque: 13 N*m (130 kgf*cm, 9 ft.*lbf)
  
  NOTE: Do not push the shift lever too hard.
  
  Fig 10: Locating Floor Shift Gear Shifting Rod Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL OIL COOLER TUBE
1. Install the oil cooler tube with the 3 bolts in the order shown in the illustration.
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
  
  Fig 11: Locating Oil Cooler Tube Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
INSPECT SHIFT LEVER POSITION (See ADJUSTMENT )
INSPECT PARK/NEUTRAL POSITION SWITCH POSITION (See ADJUSTMENT )
ADJUST PARK/NEUTRAL POSITION SWITCH POSITION (See ADJUSTMENT )
INSPECT SHIFT LEVER OPERATION (See ADJUSTMENT )
INSTALL NO. 2 ENGINE UNDER COVER (See INSTALLATION )
INSTALL FRONT FLOOR COVER CENTER (See INSTALLATION )
INSTALL BATTERY SERVICE HOLE COVER LH (See INSTALLATION )
INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (See INSTALLATION )