Valve Body Assembly: Installation

WARNING: This page is about a different car, the 2007 Lexus SC 430. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL TRANSMISSION VALVE BODY ASSEMBLY
1. Install the check ball body and spring.
  NOTE: Do not drop the check ball body and spring.
  
  Fig 1: Installing Check Ball Body And Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Confirm that the accumulator pistons, check ball body and spring are installed as shown in the illustration.
  
  Fig 2: Identifying Accumulator Spring And Check Ball Body And Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Align the groove of the manual valve with the lever pin.
  
  Fig 3: Locating Manual Valve And Lever Pin
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the 20 bolts.
  Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf)
  
  HINT:
  
  Each bolt length is indicated below.
  
  Bolt length:
  
  36 mm (1.42 in.) for bolt A
  
  25 mm (0.98 in.) for bolt B
  
  45 mm (1.77 in.) for bolt C
  
  50 mm (1.97 in.) for bolt D
  
  Fig 4: Identifying Bolt Length
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT TRANSMISSION WIRE
1. Connect the 9 connectors to the solenoid valves.
  
  Fig 5: Locating Solenoid Valves Connectors
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 2 clamps with the 2 bolts.
  Torque: 6.4 N*m (65 kgf*cm, 57 in.*lbf) for bolt A
  
  10 N*m (102 kgf*cm, 7 ft.*lbf) for bolt B
  
  Fig 6: Locating Bolts And Clamps
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the ATF temperature sensor and lock plate with the bolt.
  
  Fig 7: Locating ATF Temperature Sensor And Lock Plate Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
INSTALL VALVE BODY OIL STRAINER ASSEMBLY
1. Coat a new O-ring with ATF.
2. Install the O-ring.
  
  Fig 8: Locating O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the oil strainer with the 4 bolts.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  Fig 9: Locating Oil Strainer Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
1. Install the 3 magnets in the oil pan.
  
  Fig 10: Identifying Oil Pan Magnet
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install a new gasket and the oil pan to the transmission case with the 20 bolts.
  Torque: 4.4 N*m (45 kgf*cm, 39 in.*lbf)
  
  Fig 11: Locating Transmission Case Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY
1. Install the bracket with the 4 bolts and 2 nuts.
  
  Fig 12: Locating Exhaust Pipe Support Bracket Sub-Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 43 N*m (438 kgf*cm, 32 ft.*lbf)
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
ADD AUTOMATIC TRANSMISSION FLUID
1. Add automatic transmission fluid (see ADJUSTMENT ).
PERFORM INITIALIZATION
1. Perform initialization (see INITIALIZATION ).
  NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.