Data List/Active Test

HINT:

Using the Techstream to read the Data List allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the menus.
5. Enter the following menus: Body Electrical/Smart Access/Data List.
6. According to the display on Techstream, read the "Data List".

   Smart Access: 

   TESTER DISPLAY REFERRENCE CHART
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Ignition Switch	Engine switch on (IG) signal/ON or OFF	ON: Engine switch on (ACC, IG) OFF: Engine switch off or on (ACC)	-
   Immobilizer	Engine immobilizer system status/Set or Unset	Set: Key is not in cabin Unset: Key is in cabin	-
   Master Key	Master key code signal/Match or No Match	Match: Master key code is sent No Match: Unmatched master key code is sent	-
   Different Encrypt Code	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Different Serial Number	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Frame Error	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Response	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   BCC Malfunction	Transponder chip signal/OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Abnormal Status	Transponder chip data/OK or NG	OK: Data OK NG: Data error	-
   ID-BOX Sleep Condition	ID code box condition/Yes or No	Yes: ID code box can be sleep condition No: ID code box cannot be sleep condition	-
   ID-BOX Start Condition	ID code box condition/Yes or No	Yes: ID code box sends wake up signal No: ID code box does not send wake up signal	-
   EFI Code Receive	SFI code receive (when DTC detected) /OK or NG	OK: SFI code is received NG: SFI code is not received	-
   S Code Check	S code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
   L Code Check	L code verification result/OK or NG	OK: Verification is confirmed NG: Verification is not confirmed	-
   Unlock Request Receive	Steering unlock unlock command reception status/OK or NG	OK: Steering unlock request is received NG: Steering unlock request is not received	-
   Lock Request Receive	Steering lock command reception status/OK or NG	OK: Steering lock request is received NG: Steering lock request is not received	-
   EFI communication	SFI communication/OK or NG	OK: SFI communication is normal NG: SFI communication is abnormal	-
   Engine Start Request	ID code box start request condition/OK or NG	OK: Start request condition signal is received (past) NG: Start request condition signal is not received (past)	-
   S Code Check (Past)	S code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-
   L Code Check (Past)	L code verification result (past)/ OK or NG	OK: Verification is confirmed (past) NG: Verification is not confirmed (past)	-

HINT:

Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing Active Test.

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical/Smart Access/Active Test.
5. According to the display on Techstream, perform the "Active Test".

   Smart Access: 

   TESTER DISPLAY REFERRENCE CHART
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Security Indicator	Security indicator light (for driver side and front passenger side)	ON or OFF	-