Data List / Active Test

HINT: 

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Radar Cruise / Data List.
5. Read the Data List according to the display on the Techstream.
   RADAR CRUISE (HYBRID VEHICLE CONTROL ECU):
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Accel Request	Accelerator request signal / min.: -2,621.44 k/h/s, max.: 2,621.36 k/h/s	No vehicle in front	-
   Vehicle Distance	Millimeter wave radar sensor / min.: 0 m (0 ft), max.: 255 m (836.65 ft)	Distance to vehicle in front	-
   L/C Option Flag	Dynamic radar cruise option flag / No or Yes	Yes: Dynamic radar cruise control system can be used No: Dynamic radar cruise control system cannot be used	-
   Car Dist Time Setting	Vehicle distance time setting condition / Shrt, Mid, Long, No	Vehicle-to-vehicle distance selected by steering pad switch (distance control switch)	-
   O/D Cut Request	O/D cut request / Not Request or Request	Not Request: Idling	-
   Shift Down Rqst to 3rd	Shift down request to 3rd gear / Not Request or Request	Not Request: Idling	-
   Shift Down Rqst to 4th	Shift down request to 4th gear / Not Request or Request	Not Request: Idling	-
   Alarm Request	Alarm request signal / Not Request or Request	Request: When beeping Not Request: When not beeping	-
   All Throttle Close Rqst	All throttle close request / Not Request or Request	ON: Request OFF: Not Request	-
   Brake Control Request	Brake control request / Not Request or Request	ON: Request OFF: Not Request	-
   Targ Decl Slope	Cruise target deceleration slope / 0, 1, 2, 3	0, 1, 2, 3	-
   CCS Vehicle Spd	Vehicle speed sensor / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed	-
   CCS Mem Vehicle Spd	Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Memorized speed: Cruise control activated	-
   Throttle Opening Angle	Required throttle opening angle / min.: 0°, max.:125°	Actual required throttle opening	-
   Cruise Control	Cruise control system active condition / ON or OFF	ON: Cruise control activated OFF: Cruise control deactivated	-
   Main SW M-CPU	Main switch signal (Main CPU) / ON or OFF	ON: Main switch on OFF: Main switch off	3
   CCS Ready M-CPU	Cruise control system standby condition (Main CPU) / ON or OFF	Each time main switch is pushed, ON/OFF changes	1
   CCS Indicator M-CPU	Cruise indicator signal (Main CPU) / ON or OFF	ON: "CRUISE" on OFF: "CRUISE" off	2
   CCS Indicator S-CPU	Cruise indicator signal (Sub CPU) / ON or OFF	ON: "CRUISE" on OFF: "CRUISE" off	2
   Cancel Switch	CANCEL switch signal / ON or OFF	ON: CANCEL switch on OFF: CANCEL switch off	-
   SET/COAST Switch	SET/COAST switch signal / ON or OFF	ON: - (COAST)/SET switch on OFF: - (COAST)/SET switch off	-
   RES/ACC Switch	RES/ACC switch signal / ON or OFF	ON: + (ACCEL)/RES (RESUME) switch on OFF: + (ACCEL)/RES (RESUME) switch off	-
   Stop Light SW M-CPU	Stop light switch signal (Main CPU) / ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
   Cruise Operation Status	Cruise control condition / ON or OFF	ON: Cruise control operated OFF: Cruise control operation stopped	-
   VSC Fail Safe Flag	VSC fail-safe flag / ON or OFF	ON: Vehicle stability control system fail-safe flag on OFF: Vehicle stability control system fail-safe flag off	-
   Vehicle Spd Change	Vehicle speed sudden change / ON or OFF	ON: Sudden change in vehicle speed OFF: No change in vehicle speed	-
   # Codes	Number of DTC recorded / 0 to 255	Number of DTCs will be displayed	-

   HINT: 

   • 1 is OK, but 2 is NG → Hybrid vehicle control ECU failure
   • 2 is OK, but 3 is NG → DTC output or hybrid vehicle control ECU failure
   • 1 is OK, but cruise main indicator light does not illuminate → Cruise main indicator light, wire harness, or hybrid vehicle control ECU failure

HINT: 

Using the Techstream to perform active tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data list information can be displayed while performing Active tests.

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Combination Meter / Active Test.
5. Perform Active Test according to the display on the Techstream.

   HINT: 

   The power switch must be turned on to proceed with the Active Test using the Techstream.

   COMBINATION METER
   
   

   Tester Display	Test Part	Control Range	Control Range
   Indicat. Lamp Cruise	Cruise main indicator light	BLINK / OFF	-