Reverse Shift-linked Function of Power Mirrors does not Operate (To 8/2009): Procedure

1. Turn the engine switch on (IG).
   Fig 1: Turn The Mirror Surface To The Fully Left Position

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.
   TEXT IN ILLUSTRATION
   
   

   *1	Turn to Left Fully

3. Press the M1 switch while the SET switch is being pressed.
4. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.
5. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.
6. Press the M1 switch.
7. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

   Result

   Result	Proceed to
   Memory and reactivation function is normal.	A
   Memory function is not normal.	B
   Reactivation function is not normal.	C

C → See step   12 

B → See step   11 

A: Go to next step 

1. Use the Techstream to check if the CAN communication system is functioning normally. Refer to HOW TO PROCEED WITH TROUBLESHOOTING .

   OK

   CAN communication DTC is not output.

NG → See step   13 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine / DTC.
5. Check if DTC P0705 is output.

   OK

   DTC P0705 is not output.

NG → See step   14 

OK: Go to next step 

1. Check if the shift position indicator light in the combination meter assembly operates normally.

   OK

   The shift position indicator light indicates the actual shift position correctly.

NG → See step   15 

OK: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Master Switch / Data List.
5. Read the Data List according to the display on the Techstream.
   MASTER SWITCH
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Mirror Selection SW (R)	Mirror select switch R signal / ON or OFF	ON: Mirror select switch R is on OFF: Mirror select switch R is off	-
   Mirror Selection SW (L)	Mirror select switch L signal / ON or OFF	ON: Mirror select switch L is on OFF: Mirror select switch L is off	-

   ON

   ON and OFF appear on the screen.

NG → See step   16 

OK: Go to next step 

1. Turn the engine switch on (IG).
   Fig 2: Mirror Surface Turns Downward

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Set the mirror select switch to L to R.
3. Check that the mirror surface turns downward when the shift lever is moved to R.

   Result

   Result	Proceed to
   Reverse shift-linked function on both mirrors is not normal	A
   Reverse shift-linked function on RH side is not normal	B
   Reverse shift-linked function on LH side is not normal	C

C → See step   9 

B → See step   7 

A → See step   17 

1. Replace the outer rear view mirror assembly RH. Refer to REMOVAL .

NEXT: Go to next step 

1. Turn the engine switch on (IG).
   Fig 3: Mirror Surface Turns Downward

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Set the mirror select switch to L to R.
3. Check that the mirror surface turns downward when the shift lever is moved to R.

   OK

   Reverse shift-linked function is normal.

NG → See step   18 

OK → END (OUTER REAR VIEW MIRROR ASSEMBLY RH WAS DEFECTIVE) 

1. Replace the outer rear view mirror assembly LH. Refer to REMOVAL .

NEXT: Go to next step 

1. Turn the engine switch on (IG).
   Fig 4: Mirror Surface Turns Downward

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Set the mirror select switch to L to R.
3. Check that the mirror surface turns downward when the shift lever is moved to R.

   OK

   Reverse shift-linked function is normal.

NG → See step   19 

OK → END (OUTER REAR VIEW MIRROR ASSEMBLY LH WAS DEFECTIVE)