LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Lexus >> 2011 >> GS 450h >> Repair and Diagnosis >> Brakes >> Traction Control >> Electronically Controlled Brake System (Diagnostics - Introduction) >> Electronically Controlled Brake System >> DTC Check / Clear >> DTC Check / Clear
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Check / Clear

  1. DTC CHECK/CLEAR (WHEN USING TECHSTREAM) 
    1. DTC check
      1. Connect the Techstream to the DLC3.
      2. Turn the power switch ON (IG).
      3. Read the DTCs following the prompts on the tester screen.
    2. DTC clear
      1. Connect the Techstream to the DLC3.
      2. Turn the power switch ON (IG).
      3. Operate the Techstream to clear the codes.

        HINT: 

        Refer to the Techstream operator's manual for further details.

  2. DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE) 
    1. DTC check
      Fig 1: Identifying DLC3 Connector Terminals
      GTY155784Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
        • SST: 09843-18040 
      2. Turn the power switch ON (IG).
      3. Observe the blinking pattern of the ABS warning, brake control warning and slip indicator lights in order to identify the DTC.

        HINT: 

        If no code appears, inspect the TC and CG terminal circuit, and ABS warning, brake control warning and slip indicator light circuits.

        Trouble Area See procedure
        TC and CG terminal circuit Refer to TC and CG Terminal Circuit
        ABS warning light circuit Refer to ABS Warning Light Remains ON or. Refer to ABS Warning Light does not Come ON
        Brake control warning light circuit Refer to Brake Control Warning Light Remains ON or. Refer to Brake Control Warning Light does not Come ON
        Slip indicator light circuit Refer to Slip Indicator Light Remains ON or. Refer to Slip Indicator Light does not Come ON
      4. As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21 for the ABS warning, brake control warning and slip indicator lights.
        Fig 2: Normal System Code And Trouble Codes - Blinking Patterns
        GTY101509Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      5. Codes are explained in the code table. Refer to DIAGNOSTIC TROUBLE CODE CHART .
      6. After completing the check, disconnect terminals TC and CG of the DLC3, and turn the display off.

        If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.

    2. DTC clear
      1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
        Fig 3: Identifying DLC3 Connector Terminals
        GTY155784Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        • SST: 09843-18040 
      2. Turn the power switch ON (IG).
      3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.
        Fig 4: Depressing Brake Pedal
        GTY124492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Check that the warning light indicates a normal system code.
      5. Remove SST from the terminals of the DLC3.

        HINT: 

        Clearing the DTCs cannot be performed by removing the battery cable or the ECU-IG LH fuse.

  3. END OF DTC CHECK/CLEAR (WHEN USING SST CHECK WIRE) 
    1. Turn the power switch ON (IG).
    2. Check that the ABS warning, brake control warning and slip indicator lights go off after the power switch is turned ON (READY).
scientia non olet · About LEMON Manuals