DTC P0607-96: Control Module Performance Bank 1 Component Internal Failure [10/2014 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine / Trouble Codes.
5. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   P0607-96 and P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 are output	A
   P0607-96 is output	B

Result: 

B 

See step  3

Result: 

A 

See step  2

1. Refer to the P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 flowchart.

   HINT: 

   • If P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

     Refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [10/2014 - 09/2015] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [09/2015 - 09/2017] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [09/2017 - 05/2018] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [05/2018 - ]

   • If DTC P0607-96 and P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  6

1. Allow the engine to idle, and then rev the engine.
2. Check for exhaust gas leaks around the heated oxygen sensor.

   If any exhaust gas leaks are present, repair them and proceed to "Perform Confirmation Driving Pattern". If no exhaust gas leaks are present, proceed to "Perform Confirmation Driving Pattern".

   HINT: 

   • If no exhaust gas leaks are present, there may be a malfunction in the heated oxygen sensor circuit.
   • If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.
   • Perform "Inspection After Repair" after repairing or replacing the exhaust system.

     Refer to INITIALIZATION [10/2014 - 05/2019] , or refer to INITIALIZATION [05/2019 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Connect the Techstream to the DLC3.
3. Start the engine.
4. Warm up the engine until the engine coolant temperature is 75°C (167°F) or higher.
5. Perform the driving pattern.
   WARNING:

   When performing the confirmation driving pattern, obey all speed limits and traffic laws.

   1. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.
   2. Drive the vehicle between 60 and 80 km/h (37 and 50 mph) for 5 minutes.
6. Enter the following menus: Powertrain / Engine / Trouble Codes.
7. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   P0136-11, P0136-13, P0136-14, P0136-15, P0136-17, P0136-23 and/or P0607-96 are output	A
   Only P0607-96 is output	B
   DTC is not output	C

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [10/2014 - 05/2019]  , or refer to  REMOVAL [05/2019 - ] 

Result: 

C 

See step  6

Result: 

A 

See step  5

1. Refer to the P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 flowchart.

   HINT: 

   • If P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 is output, troubleshoot for that DTC first. Then proceed to "Inspect ECM".

     Refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [10/2014 - 09/2015] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [09/2015 - 09/2017] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [09/2017 - 05/2018] , or refer to DTC P0136-11: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground; DTC P0136-13: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open; DTC P0136-14: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open; DTC P0136-15: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open; DTC P0136-17: O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold; DTC P0136-23: O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low; DTC P013A-00: O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 [05/2018 - ]

   • If DTC P0607-96 and P0136-11, P0136-13, P0136-14, P0136-15, P0136-17 or P0136-23 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or higher).

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  6

1. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

2. Stop the engine and wait for 30 minutes.
3. Connect the Techstream to the DLC3.
4. Turn the engine switch on (IG) and turn the Techstream on.
5. Start the engine and allow it to idle for 2 minutes.
6. Turn the Techstream on.
7. Enter the following menus: Powertrain / Engine / Trouble Codes.
8. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC is not output	A
   DTC P0607-96 is output	B

Result: 

A 

END 

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [10/2014 - 05/2019]  , or refer to  REMOVAL [05/2019 - ]