Cruise-Control Module (C-CM) DTC Chart
CRUISE-CONTROL MODULE (C-CM) DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Action |
|---|---|---|
| C0072:00 | Brake Temperature Too High: No Sub Type Information | REFER to VEHICLE DYNAMIC SYSTEMS to continue diagnosis of the ABS system. |
| C1105:11 | Brake Lamp Control: Circuit Short To Ground | Go To PINPOINT TEST D . |
| C1105:12 | Brake Lamp Control: Circuit Short To Battery | Go To PINPOINT TEST D . |
| C1105:19 | Brake Lamp Control: Circuit Current Above Threshold | Go To PINPOINT TEST D . |
| C1A67:11 | Forward Looking Sensor: Circuit Short To Ground | Go To PINPOINT TEST E . |
| C1A67:12 | Forward Looking Sensor: Circuit Short To Battery | Go To PINPOINT TEST E . |
| C1A67:19 | Forward Looking Sensor: Circuit Current Above Threshold | Go To PINPOINT TEST E . |
| C1A67:54 | Forward Looking Sensor: Missing Calibration | Go To PINPOINT TEST K . |
| C1A67:81 | Forward Looking Sensor: Invalid Serial Data Received | Go To PINPOINT TEST F . |
| C1A67:87 | Forward Looking Sensor: Missing Message | Go To PINPOINT TEST H . |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | Go To PINPOINT TEST F . |
| C1A67:97 | Forward Looking Sensor: Component or System Operation Obstructed or Blocked | Go To PINPOINT TEST N . |
| C1A67:98 | Forward Looking Sensor: Component or System Over Temperature | Go To PINPOINT TEST F . |
| U0001:88 | High Speed CAN Communication Bus: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U0073:00 | Lost Communication Bus "A" Off: No Sub Type Information | Go To PINPOINT TEST H . |
| U0100:00 | Lost Communication: With ECM /PCM "A": No Sub Type Information | Go To PINPOINT TEST L . |
| U0121:00 | Lost Communication: With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | Go To PINPOINT TEST A . |
| U0155:00 | Lost Communication: With Instrument Panel Cluster (IPC ) Control Module: No Sub Type Information | Go To PINPOINT TEST A . |
| U0401:00 | Invalid Data Received from ECM /PCM A: No Sub Type Information | Go To PINPOINT TEST G . |
| U0401:67 | Invalid Data Received from ECM /PCM A: Signal Incorrect After Event | Go To PINPOINT TEST G . |
| U0401:81 | Invalid Data Received from ECM /PCM A: Invalid Serial Data Received | Go To PINPOINT TEST G . |
| U0415:81 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid Serial Data Received | CLEAR the DTCs. REPEAT the self-test. If DTC U0415:81 is retrieved again, REFER to VEHICLE DYNAMIC SYSTEMS to continue diagnosis of the ABS. |
| U0415:86 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Invalid | CLEAR the DTCs. REPEAT the self-test. If DTC U0415:86 is retrieved again, REFER to VEHICLE DYNAMIC SYSTEMS to continue diagnosis of the ABS. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC C3000:41 is retrieved again, INSTALL a new Cruise-Control Module (C-CM). REFER to CRUISE-CONTROL MODULE (C-CM) . TEST the system for normal operation. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. RETEST the adaptive cruise control system. REPEAT the self-test. If DTC C3000:42 is retrieved again, INSTALL a new C-CM . REFER to CRUISE-CONTROL MODULE (C-CM) . TEST the system for normal operation. |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC C3000:49 is retrieved again, INSTALL a new C-CM . REFER to CRUISE-CONTROL MODULE (C-CM) . TEST the system for normal operation. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | Go To PINPOINT TEST I . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | Go To PINPOINT TEST J . |