ABS Module DTC Chart
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) LIST
| DTC | Description | Source | Action |
|---|---|---|---|
| B1342 | ECU is Faulted | ABS Module | CLEAR the DTCs. REPEAT the self-test. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| B1596 | Service Continuous Codes | ABS Module | This DTC is only an indicator that other DTCs are present. This DTC will set after clearing DTCs with the scan tool. An ignition key-cycle from OFF to RUN is required to set this DTC as a Continuous Memory Diagnostic Trouble Code (CMDTC) which will allow the ABS module to check for other on-demand DTCs. CLEAR the DTCs. CYCLE the ignition switch. RETRIEVE the DTCs. If only DTC B1596 is present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| B1676 | Battery Pack Voltage Out of Range | ABS Module | Go To PINPOINT TEST A . |
| B2477 | Module Configuration Failure | ABS Module | CONFIGURE the ABS module using as-built data and correct tire size. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . CYCLE the ignition switch and REPEAT the self test. If DTC B2477 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| B2900 | VIN Mismatched | ABS Module | Go To PINPOINT TEST F . |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | Go To PINPOINT TEST B . |
| C1222 | Wheel Speed Sensor Mismatch | ABS Module | Go To PINPOINT TEST C . |
| C1266 | ABS Valve Power Relay Circuit Failure | ABS Module | Go To PINPOINT TEST D . |
| C1278 | Steering Wheel Angle 1 and 2 Signal Faulted | ABS Module | Go To PINPOINT TEST H . |
| C1279 | Yaw Rate Sensor Circuit Failure | ABS Module | Go To PINPOINT TEST I . |
| C1280 | Yaw Rate Sensor Signal Fault | ABS Module | Go To PINPOINT TEST I . |
| C1281 | Lateral Acceleration Sensor Circuit Fault | ABS Module | Go To PINPOINT TEST I . |
| C1282 | Lateral Accelerometer Signal Fault | ABS Module | Go To PINPOINT TEST I . |
| C1288 | Pressure Transducer Main/Primary Input Circuit Failure | ABS Module | Go To PINPOINT TEST J . |
| C1296 | Wheel Speed LF Signal Fault | ABS Module | Go To PINPOINT TEST C . |
| C1297 | Wheel Speed RF Signal Fault | ABS Module | Go To PINPOINT TEST C . |
| C1298 | Wheel Speed RR Signal Fault | ABS Module | Go To PINPOINT TEST C . |
| C1299 | Wheel Speed LR Signal Fault | ABS Module | Go To PINPOINT TEST C . |
| C1300 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go To PINPOINT TEST E . |
| C1440 | Pressure Transducer Main/Primary Signal Faulted | ABS Module | Go To PINPOINT TEST J . |
| C1446 | Brake ON/OFF Plausibility Fault(s) | ABS Module | Go To PINPOINT TEST J . |
| C1484 | Brake ON/OFF Electrical Fault | ABS Module | Go To PINPOINT TEST J . |
| C1805 | Mismatched PCM and/or ABS-TC Module | ABS Module | CONFIGURE the ABS module using as-built data and correct tire size. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . CYCLE the ignition switch and REPEAT the self test. If DTC C1805 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . REPEAT the self-test. |
| C1956 | Steering Angle Sensor Circuit Failure | ABS Module | Go To PINPOINT TEST H . |
| C1963 | Stability Assist Inhibit Warning | ABS Module |
NOTE:
This DTC will not clear until the vehicle has been driven above 48 km/h (30 mph) with input from the steering wheel rotation sensor.
NOTE:
REPAIR all other steering wheel angle sensor and stability control sensor cluster DTCs before repairing DTC C1963. Go To PINPOINT TEST H
. |
| C1975 | IVD Plausibility Failure | ABS Module |
NOTE:
REPAIR all other steering wheel angle sensor and stability control sensor cluster DTCs before repairing DTC C1975. Go To PINPOINT TEST H
. |
| C2769 | Longitudinal Acceleration Sensor Circuit Fault | ABS Module | Go To PINPOINT TEST I . |
| C2770 | Longitudinal Acceleration Sensor Signal Fault | ABS Module | Go To PINPOINT TEST I . |
| U0073 | Control Module Communication Bus A Off | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |
| U0074 | Control Module Communication Bus B Off | ABS Module | Go To PINPOINT TEST I . |
| U0100 | Lost Communication With ECM /PCM | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |
| U0155 | Lost Communication With Instrument Panel Cluster Control Module | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |
| U0102 | Lost Communication With Transfer Case Control Module | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |
| U0405 | Invalid Data Received from Cruise Control Module | ABS Module | REFER to SPEED CONTROL to diagnose the speed control system. |
| U2023 | Fault Received From External Node | ABS Module | If any other communication DTCs are present in the ABS module, DIAGNOSE those first. CLEAR all ABS module DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . |
| U2050 | No Application Present | ABS Module | CONFIGURE the ABS module. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . CLEAR the DTCs. RETRIEVE the DTCs. If DTC U2050 is retrieved again, INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . CLEAR the DTC. REPEAT the self-test. |
| U2515 | Missing message for Adaptive Cruise Control | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the no communication concern. |