Side Obstacle Detection Control Module - Left (Sod-L) And Side Obstacle Detection Control Module - Right (Sod-R)

DTC INDEX

DTC	Description	Action
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to PINPOINT TEST G
U0101:00	Lost Communication with TCM: No Sub Type Information	GO to PINPOINT TEST H
U0146:00	Lost Communication with Gateway "A": No Sub Type Information	GO to PINPOINT TEST I
U0199:00	Lost Communication With "Door Control Module A": No Sub Type Information	GO to PINPOINT TEST J
U0200:00	Lost Communication With "Door Control Module B": No Sub Type Information	GO to PINPOINT TEST K
U0401:86	Invalid Data Received from ECM/PCM A: Signal Invalid	This DTC sets when the SODL or SODR receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network.
U0402:86	Invalid Data Received from TCM: Signal Invalid	This DTC sets when the SODL or SODR receives invalid network data from the TCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network.
U049A:86	Invalid Data Received From "Door Control Module A": Signal Invalid	This DTC sets when the SODL receives invalid network data from the DDM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network.
U0501:86	Invalid Data Received From "Door Control Module B": Signal Invalid	This DTC sets when the SODR receives invalid network data from the PDM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network.
U2100:00	Initial Configuration Not Complete: No Sub Type Information	This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. CHECK the vehicle service history for recent service actions related to this module. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U2300:55	Central Configuration: Not Configured	This DTC sets when the SODL or SODR do not detect the Vehicle Identification Number (VIN) information on the Medium Speed Controller Area Network (MS-CAN). RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in all other modules.
U3000:44	Control Module: Data Memory Failure	CLEAR the SODL or SODR self-test. If DTC U3000:44 returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3000:45	Control Module: Program Memory Failure	CLEAR the SODL or SODR self-test. If DTC U3000:45 returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3000:46	Control Module: Calibration/Parameter Memory Failure	CLEAR the SODL or SODR self-test. If DTC U3000:46 returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3000:48	Control Module: Supervision Software Failure	CLEAR the SODL or SODR self-test. If DTC U3000:48 returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3000:49	Control Module: Internal Electronic Failure	CLEAR the SODL or SODR self-test. If DTC U3000:49 returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3000:4A	Control Module: Incorrect Component Installed	CLEAR the SODL or SODR self-test. If DTC U3000:4A returns, INSTALL a new SODL or SODR. REFER to: SIDE OBSTACLE DETECTION CONTROL MODULE . The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.
U3002:62	Vehicle Identification Number: Signal Compare Failure	This DTC sets when the Vehicle Identification Number (VIN) stored in the SODL or SODR does not match the Vehicle Identification Number that is stored in the BCM. This may indicate that the original SODL or SODR is not installed on the vehicle and has not been configured correctly. PERFORM the PMI procedure for the SODL and SODR as directed by the scan tool. The PMI procedure must be performed on the SODL and SODR at the same time, regardless of which module is causing the concern. Failure to perform this may result in a fault condition.