| B1C03:23 |
Memory #1 Switch:Signal Stuck Low |
GO to Pinpoint Test G |
| B1C04:23 |
Memory #2 Switch:Signal Stuck Low |
GO to Pinpoint Test G |
| B1C05:23 |
Memory #3 Switch:Signal Stuck Low |
GO to Pinpoint Test G |
| B1067:24 |
Lumbar In Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1068:24 |
Lumbar Out Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1087:83 |
LIN Bus "A":Value of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AT |
| B1087:87 |
LIN Bus "A":Missing Message |
GO to Pinpoint Test AT |
| B14C3:24 |
Seat Height Rear Down Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B14C4:24 |
Seat Height Rear Up Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B14CE:11 |
Seat Horizontal Motor Output:Circuit Short To Ground |
GO to Pinpoint Test F |
| B14CE:12 |
Seat Horizontal Motor Output:Circuit Short To Battery |
GO to Pinpoint Test F |
| B14CE:13 |
Seat Horizontal Motor Output:Circuit Open |
GO to Pinpoint Test F |
| B14CF:11 |
Seat Recline Motor Output:Circuit Short To Ground |
GO to Pinpoint Test F |
| B14CF:12 |
Seat Recline Motor Output:Circuit Short To Battery |
GO to Pinpoint Test F |
| B14CF:13 |
Seat Recline Motor Output:Circuit Open |
GO to Pinpoint Test F |
| B14D0:11 |
Seat Height Front/Tilt Motor Output:Circuit Short To Ground |
GO to Pinpoint Test F |
| B14D0:12 |
Seat Height Front/Tilt Motor Output:Circuit Short To Battery |
GO to Pinpoint Test F |
| B14D0:13 |
Seat Height Front/Tilt Motor Output:Circuit Open |
GO to Pinpoint Test F |
| B14D2:11 |
Seat Height Rear Motor Output:Circuit Short To Ground |
GO to Pinpoint Test F |
| B14D2:12 |
Seat Height Rear Motor Output:Circuit Short To Battery |
GO to Pinpoint Test F |
| B14D2:13 |
Seat Height Rear Motor Output:Circuit Open |
GO to Pinpoint Test F |
| B151F:11 |
Left Cushion Motor Output:Circuit Short To Ground |
GO to Pinpoint Test D |
| B151F:12 |
Left Cushion Motor Output:Circuit Short To Battery |
GO to Pinpoint Test D |
| B151F:13 |
Left Cushion Motor Output:Circuit Open |
GO to Pinpoint Test D |
| B1520:11 |
Right Cushion Motor Output:Circuit Short To Ground |
GO to Pinpoint Test D |
| B1520:12 |
Right Cushion Motor Output:Circuit Short To Battery |
GO to Pinpoint Test D |
| B1520:13 |
Right Cushion Motor Output:Circuit Open |
GO to Pinpoint Test D |
| B1522:11 |
Lumbar Motor Output:Circuit Short To Ground |
GO to Pinpoint Test B |
| B1522:12 |
Lumbar Motor Output:Circuit Short To Battery |
GO to Pinpoint Test B |
| B1522:13 |
Lumbar Motor Output:Circuit Open |
GO to Pinpoint Test B |
| B1527:24 |
Left Cushion Fore Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1528:24 |
Left Cushion Aft Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1529:24 |
Right Cushion Fore Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B152A:24 |
Right Cushion Aft Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1B96:24 |
Seat Slide Forward Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1B97:24 |
Seat Slide Backward Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1B98:24 |
Seat Tilt Up Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1B99:24 |
Seat Tilt Down Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1C00:24 |
Seat Recline Up Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| B1C01:24 |
Seat Recline Down Switch:Signal Stuck High |
GO to Pinpoint Test AQ |
| U0100:00 |
Lost Communication With ECM/PCM "A":No Sub Type Information |
GO to Pinpoint Test W |
| U0140:00 |
Lost Communication With Body Control Module:No Sub Type Information |
GO to Pinpoint Test V |
| U0199:00 |
Lost Communication With "Door Control Module A":No Sub Type Information |
GO to Pinpoint Test AG |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module:No Sub Type Information |
GO to Pinpoint Test AH |
| U2013:24 |
Switch Pack:Signal Stuck High |
GO to Pinpoint Test AQ |
| U2100:00 |
Initial Configuration Not Complete:No Sub Type Information |
GO to Pinpoint Test AJ |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AK |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AS |
| U3500:17 |
Control Module Input Power "A" Circuit Range/Performance:Circuit Voltage Above Threshold |
GO to Pinpoint Test AI |
| B1034:11 |
Left Front Seat Heater Element:Circuit Short To Ground |
GO to Pinpoint Test N |
| B1034:15 |
Left Front Seat Heater Element:Circuit Short To Battery or Open |
GO to Pinpoint Test N |
| B1036:11 |
Right Front Seat Heater Element:Circuit Short To Ground |
GO to Pinpoint Test O |
| B1036:15 |
Right Front Seat Heater Element:Circuit Short To Battery Or Open |
GO to Pinpoint Test O |
| B1038:11 |
Left Front Seat Heater Sensor:Circuit Short To Ground |
GO to Pinpoint Test N |
| B1038:15 |
Left Front Seat Heater Sensor:Circuit Short To Battery Or Open |
GO to Pinpoint Test N |
| B103A:11 |
Right Front Seat Heater Sensor:Circuit Short To Ground |
GO to Pinpoint Test O |
| B103A:15 |
Right Front Seat Heater Sensor:Circuit Short To Battery Or Open |
GO to Pinpoint Test O |
| B1067:24 |
Lumbar In Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1068:24 |
Lumbar Out Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1087:83 |
LIN Bus "A":Value of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AU |
| B1087:87 |
LIN Bus "A":Missing Message |
GO to Pinpoint Test AU |
| B14C3:24 |
Seat Height Rear Down Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B14C4:24 |
Seat Height Rear Up Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B14CE:11 |
Seat Horizontal Motor Output:Circuit Short To Ground |
GO to Pinpoint Test A |
| B14CE:12 |
Seat Horizontal Motor Output:Circuit Short To Battery |
GO to Pinpoint Test A |
| B14CE:13 |
Seat Horizontal Motor Output:Circuit Open |
GO to Pinpoint Test A |
| B14CF:11 |
Seat Recline Motor Output:Circuit Short To Ground |
GO to Pinpoint Test A |
| B14CF:12 |
Seat Recline Motor Output:Circuit Short To Battery |
GO to Pinpoint Test A |
| B14CF:13 |
Seat Recline Motor Output:Circuit Open |
GO to Pinpoint Test A |
| B14D0:11 |
Seat Height Front/Tilt Motor Output:Circuit Short To Ground |
GO to Pinpoint Test A |
| B14D0:12 |
Seat Height Front/Tilt Motor Output:Circuit Short To Battery |
GO to Pinpoint Test A |
| B14D0:13 |
Seat Height Front/Tilt Motor Output:Circuit Open |
GO to Pinpoint Test A |
| B14D2:11 |
Seat Height Rear Motor Output:Circuit Short To Ground |
GO to Pinpoint Test A |
| B14D2:12 |
Seat Height Rear Motor Output:Circuit Short To Battery |
GO to Pinpoint Test A |
| B14D2:13 |
Seat Height Rear Motor Output:Circuit Open |
GO to Pinpoint Test A |
| B151F:11 |
Left Cushion Motor Output:Circuit Short To Ground |
GO to Pinpoint Test E |
| B151F:12 |
Left Cushion Motor Output:Circuit Short To Battery |
GO to Pinpoint Test E |
| B151F:13 |
Left Cushion Motor Output:Circuit Open |
GO to Pinpoint Test E |
| B1520:11 |
Right Cushion Motor Output:Circuit Short To Ground |
GO to Pinpoint Test E |
| B1520:12 |
Right Cushion Motor Output:Circuit Short To Battery |
GO to Pinpoint Test E |
| B1520:13 |
Right Cushion Motor Output:Circuit Open |
GO to Pinpoint Test E |
| B1522:11 |
Lumbar Motor Output:Circuit Short To Ground |
GO to Pinpoint Test C |
| B1522:12 |
Lumbar Motor Output:Circuit Short To Battery |
GO to Pinpoint Test C |
| B1522:13 |
Lumbar Motor Output:Circuit Open |
GO to Pinpoint Test C |
| B1527:24 |
Left Cushion Fore Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1528:24 |
Left Cushion Aft Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1529:24 |
Right Cushion Fore Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B152A:24 |
Right Cushion Aft Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1B96:24 |
Seat Slide Forward Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1B97:24 |
Seat Slide Backward Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1B98:24 |
Seat Tilt Up Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1B99:24 |
Seat Tilt Down Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1C00:24 |
Seat Recline Up Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| B1C01:24 |
Seat Recline Down Switch:Signal Stuck High |
GO to Pinpoint Test AR |
| U0100:00 |
Lost Communication With ECM/PCM "A":No Sub Type Information |
GO to Pinpoint Test W |
| U0140:00 |
Lost Communication With Body Control Module:No Sub Type Information |
GO to Pinpoint Test V |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module:No Sub Type Information |
GO to Pinpoint Test AH |
| U2013:24 |
Switch Pack:Signal Stuck High |
GO to Pinpoint Test AR |
| U2100:00 |
Initial Configuration Not Complete:No Sub Type Information |
GO to Pinpoint Test AJ |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AS |
| U3500:17 |
Control Module Input Power "A" Circuit Range/Performance:Circuit Voltage Above Threshold |
GO to Pinpoint Test AI |
| B1151:4B |
Passenger Seat Cushion:Over Temperature |
GO to Pinpoint Test R |
| B1153:4B |
Driver Seat Cushion:Over Temperature |
GO to Pinpoint Test Q |
| B1208:11 |
Driver Seat Cushion Temperature Sensor:Circuit Short To Ground |
GO to Pinpoint Test Q |
| B1208:15 |
Driver Seat Cushion Temperature Sensor:Circuit Short To Battery Or Open |
GO to Pinpoint Test Q |
| B1208:2A |
Driver Seat Cushion Temperature Sensor:Stuck in Range |
GO to Pinpoint Test Q |
| B120A:11 |
Passenger Seat Cushion Temperature Sensor:Circuit Short To Ground |
GO to Pinpoint Test R |
| B120A:15 |
Passenger Seat Cushion Temperature Sensor:Circuit Short To Battery Or Open |
GO to Pinpoint Test R |
| B120A:2A |
Passenger Seat Cushion Temperature Sensor:Stuck in Range |
GO to Pinpoint Test R |
| B14BD:11 |
Driver Seat Cushion Blower:Circuit Short To Ground |
GO to Pinpoint Test T |
| B14BD:13 |
Driver Seat Cushion Blower:Circuit Open |
GO to Pinpoint Test T |
| B14C0:11 |
Passenger Seat Cushion Blower:Circuit Short To Ground |
GO to Pinpoint Test U |
| B14C0:13 |
Passenger Seat Cushion Blower:Circuit Open |
GO to Pinpoint Test U |
| B1562:11 |
Driver Seat Back Blower Speed:Circuit Short To Ground |
GO to Pinpoint Test T |
| B1562:12 |
Driver Seat Back Blower Speed:Circuit Short To Battery |
GO to Pinpoint Test T |
| B1563:11 |
Passenger Seat Back Blower Speed:Circuit Short To Ground |
GO to Pinpoint Test U |
| B1563:12 |
Passenger Seat Back Blower Speed:Circuit Short To Battery |
GO to Pinpoint Test U |
| B1564:11 |
Driver Seat Cushion Blower Speed:Circuit Short To Ground |
GO to Pinpoint Test T |
| B1564:12 |
Driver Seat Cushion Blower Speed:Circuit Short To Battery |
GO to Pinpoint Test T |
| B1565:11 |
Passenger Seat Cushion Blower Speed:Circuit Short To Ground |
GO to Pinpoint Test U |
| B1565:12 |
Passenger Seat Cushion Blower Speed:Circuit Short To Battery |
GO to Pinpoint Test U |
| U0140:00 |
Lost Communication With Body Control Module:No Sub Type Information |
GO to Pinpoint Test X |
| U0257:00 |
Lost Communication with Front Controls / Display Interface Module:No Sub Type Information |
GO to Pinpoint Test Y |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled:No Sub Type Information |
GO to Pinpoint Test AL |
| U2100:00 |
Initial Configuration Not Complete:No Sub Type Information |
GO to Pinpoint Test AM |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AK |
| B146F:00 |
Back Bladder System Electropneumatic Failure:No Sub Type Information |
GO to Pinpoint Test K |
| B146F:04 |
Back Bladder System Electropneumatic Failure:System Internal Failures |
GO to Pinpoint Test K |
| B1470:00 |
Cushion Bladder System Electropneumatic Failure:No Sub Type Information |
GO to Pinpoint Test K |
| B1470:04 |
Cushion Bladder System Electropneumatic Failure:System Internal Failures |
GO to Pinpoint Test K |
| B1473:11 |
Pump Driver:Circuit Short To Ground |
GO to Pinpoint Test K |
| U0140:00 |
Lost Communication With Body Control Module:No Sub Type Information |
GO to Pinpoint Test Z |
| U0208:00 |
Lost Communication With "Seat Control Module A":No Sub Type Information |
GO to Pinpoint Test AA |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module:No Sub Type Information |
GO to Pinpoint Test AC |
| U0256:00 |
Lost Communication With Front Controls Interface Module "A":No Sub Type Information |
GO to Pinpoint Test AD |
| U0422:00 |
Invalid Data Received From Body Control Module:No Sub Type Information |
GO to Pinpoint Test AE |
| U0455:00 |
Invalid Data Received From Restraints Occupant Classification System Module:No Sub Type Information |
GO to Pinpoint Test AF |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled:No Sub Type Information |
GO to Pinpoint Test AN |
| U2100:00 |
Initial Configuration Not Complete:No Sub Type Information |
GO to Pinpoint Test AO |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AP |
| B146F:00 |
Back Bladder System Electropneumatic Failure:No Sub Type Information |
GO to Pinpoint Test L |
| B146F:04 |
Back Bladder System Electropneumatic Failure:System Internal Failures |
GO to Pinpoint Test L |
| B1470:00 |
Cushion Bladder System Electropneumatic Failure:No Sub Type Information |
GO to Pinpoint Test L |
| B1470:04 |
Cushion Bladder System Electropneumatic Failure:System Internal Failures |
GO to Pinpoint Test L |
| B1473:11 |
Pump Driver:Circuit Short To Ground |
GO to Pinpoint Test L |
| U0140:00 |
Lost Communication With Body Control Module:No Sub Type Information |
GO to Pinpoint Test Z |
| U0208:00 |
Lost Communication With "Seat Control Module A":No Sub Type Information |
GO to Pinpoint Test AA |
| U024B:00 |
Lost Communication with Seat Control Module "G":No Sub Type Information |
GO to Pinpoint Test AB |
| U0253:00 |
Lost Communication With Accessory Protocol Interface Module:No Sub Type Information |
GO to Pinpoint Test AC |
| U0256:00 |
Lost Communication With Front Controls Interface Module "A":No Sub Type Information |
GO to Pinpoint Test AD |
| U0422:00 |
Invalid Data Received From Body Control Module:No Sub Type Information |
GO to Pinpoint Test AE |
| U0455:00 |
Invalid Data Received From Restraints Occupant Classification System Module:No Sub Type Information |
GO to Pinpoint Test AF |
| U1000:00 |
Solid State Driver Protection Active -Driver Disabled:No Sub Type Information |
GO to Pinpoint Test AN |
| U2100:00 |
Initial Configuration Not Complete:No Sub Type Information |
GO to Pinpoint Test AO |
| U3000:49 |
Control Module:Internal Electronic Failure |
GO to Pinpoint Test AP |