Common Specifications & Procedures
MKZ (EXCEPT HYBRID)
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Except Hybrid | ||||
| Service | Specifications | |||
| Torque | Refer to the specific component in Removal And Installation . | |||
| Axle/Hub Nut | 148 lb.ft (200 Nm) | |||
| Battery | ||||
| Except Hybrid | Specifications | |||
| Brakes RR, LR, RF, LF |
||||
| Except Hybrid | ||||
| Bleeding Sequence | Brake System Pressure Bleeding | |||
| Front Disc Brakes w/Torque | Refer to the appropriate component in Removal And Installation | |||
| Rear Disc Brakes w/Torque | Refer to the appropriate component in Removal And Installation | |||
| Charging | ||||
| Generator w/Torque | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | Generator and Stud: 62 lb.in (7 Nm) Upper Generator Bolt: 18 lb.ft (25 Nm) Lower Generator Bolts: 18 lb.ft (25 Nm) |
|||
| 3.0L EcoBoost | Generator Bolt and Stud Nut: 35 lb.ft (47 Nm) | |||
| Drive Belts | ||||
| Except Hybrid | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ||||
| Adjustment | Accessory Drive Belt | |||
| Belt Routing | Accessory Drive - Component Location | |||
| 3.0L EcoBoost | ||||
| Adjustment | Accessory Drive Belt | |||
| Belt Routing | Accessory Drive - Component Location | |||
| Engine Cooling | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | ||||
| General Service Specifications | Specifications | |||
| Thermostat R & I | Thermostat Housing | |||
| Water Pump R&I | Coolant Pump | |||
| 3.0L Ecoboost | ||||
| General Service Specifictions | Specifications | |||
| Thermostat R & I | Thermostat | |||
| Water Pump R&I | Coolant Pump | |||
| Engine Mechanical | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ||||
| Compression | Specifications | |||
| Oil Pressure | Oil pressure (hot @ 2, 000 rpm) 29-60 psi (200-414 kPa) |
|||
| Overhaul | Specifications | |||
| Torque | Refer to the appropriate component in Removal And Installation | |||
| 3.0L EcoBoost | ||||
| Compression | Specifications | |||
| Oil Pressure | Reading 1: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park 21 psi (144.8 kPa) Reading 2: Minimum average oil pressure @ 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected) Reading 1 value plus 8 psi (55.1 kPa) |
|||
| Overhaul | Specifications | |||
| Torque | Refer to the appropriate component in Removal And Installation (1 of 2) and Removal And Installation (2 of 2) | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| Automatic/Manual | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | For tightening bolt sequence, refer to Flexplate Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
|||
| 3.0L EcoBoost | For tightening bolt sequence, refer to Flexplate
. 59 lb.ft (80 Nm) |
|||
| Fuel System | ||||
| Fuel Filter Location | Lifetime filter part of Fuel Pump Module. | |||
| Fuel Filter R & I | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | Fuel Pump And Sender Unit | |||
| 3.0L Ecoboost | Fuel Pump And Sender Unit - FWD or Fuel Pump And Sender Unit - AWD | |||
| Pressure Release Procedure | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | Fuel System Pressure Release | |||
| 3.0L Ecoboost | Fuel System Pressure Release | |||
| Pressure Specification | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | Engine Running: 46.4 -79.8 psi (320 -550 kPa) | |||
| 3.0L Ecoboost | Engine Running: 46.4 -79.8 psi (320 -550 kPa) | |||
| Fuel Pressure Test Procedure | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | Fuel System Pressure Check - 2.0L Ecoboost (184kW/250PS) - MI4 | |||
| 3.0L Ecoboost | Fuel System Pressure Check | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | |||
| Ignition Routing | Engines have coil-on-plug ignition. | |||
| Spark Plugs | ||||
| Type | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | CYFS 12Y PCT | |||
| 3.0L EcoBoost | CYFS 12Y PT | |||
| Gap | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | 0.030 in (.75 mm) | |||
| 3.0L EcoBoost | 0.028 -0.031 in (.7 -.8 mm) | |||
| Torque | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | 106 lb.in (12 Nm) | |||
| 3.0L EcoBoost | 133 lb.in (15 Nm) | |||
| Starting | ||||
| Starter w/Torque | ||||
| 2.0L Ecoboost (184KW/250PS) - MI4 | Starter Motor Studbolts: 35 lb.ft (48 Nm) | |||
| 3.0L Ecoboost | Starter Motor Studbolts: 35 lb.ft (48 Nm) | |||
| Wheel Alignment | ||||
| Adjustment Specifications | Specifications (Except Hybrid) | |||
| Torque | Refer to the appropriate procedure in General Procedures . | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel And Tire
. 150 Ft. Lbs. (204 N.m) |
|||