Anti-Lock Brake System And Stability Control DTCS
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B10DA:51 | PATS Target Identifier: Not Programmed | GO to Pinpoint Test P |
| C0030:07 | Left Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| C0031:01 | Left Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test M |
| C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| C0033:07 | Right Front Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| C0034:01 | Right Front Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test M |
| C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| C0036:07 | Left Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| C0037:01 | Left Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test N |
| C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| C0039:07 | Right Rear Tone Wheel: Mechanical Failures | GO to Pinpoint Test AB |
| C003A:01 | Right Rear Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test N |
| C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test AB |
| C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| C0040:01 | Brake Pedal Switch 'A': General Electrical Failure | GO to Pinpoint Test CW |
| C0040:04 | Brake Pedal Switch 'A': System Internal Failures | GO to Pinpoint Test CW |
| C0040:64 | Brake Pedal Switch 'A': Signal Plausibility Failure | GO to Pinpoint Test CW |
| C0041:01 | Brake Pedal Switch 'B': General Electrical Failure | GO to Pinpoint Test CW |
| C0041:14 | Brake Pedal Switch 'B': Circuit Short To Ground Or Open | GO to Pinpoint Test CW |
| C0041:4B | Brake Pedal Switch 'B': Over Temperature | GO to Pinpoint Test CW |
| C0044:49 | Brake Pressure Sensor 'A': Internal Electronic Failure | GO to Pinpoint Test AM |
| C0044:64 | Brake Pressure Sensor 'A': Signal Plausibility Failure | GO to Pinpoint Test AM |
| C0044:8F | Brake Pressure Sensor 'A': Erratic | GO to Pinpoint Test AM |
| C0047:01 | Brake Booster Pressure Sensor: General Electrical Failure | GO to Pinpoint Test CO |
| C0047:1C | Brake Booster Pressure Sensor: Circuit Voltage Out Of Range | GO to Pinpoint Test CO |
| C0047:31 | Brake Booster Pressure Sensor: No Signal | GO to Pinpoint Test CO |
| C0047:64 | Brake Booster Pressure Sensor: Signal Plausibility Failure | GO to Pinpoint Test CO |
| C0049:01 | Brake Fluid Level: General Electrical Failure | GO to Pinpoint Test L |
| C0049:7B | Brake Fluid Level: Low Fluid Level | GO to Pinpoint Test L |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test LA |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test LA |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test LA |
| C0051:96 | Steering Wheel Position Sensor: Component Internal Failure | GO to Pinpoint Test LA |
| C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test BH |
| C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test BH |
| C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | GO to Pinpoint Test AN |
| C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test BH |
| C0063:28 | Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test BH |
| C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test BH |
| C0064:28 | Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test BH |
| C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test BH |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test AD |
| C0072:4B | Brake Temperature Too High: Over Temperature | GO to Pinpoint Test X |
| C0078:56 | Tire Diameter: Invalid/Incompatible Configuration | GO to Pinpoint Test ZA |
| C052F:00 | ABS Pump Motor Supply Voltage 'A' Circuit/Open: No Sub Type Information | GO to Pinpoint Test A |
| C0564:00 | ABS Control Module System Voltage Low: No Sub Type Information | GO to Pinpoint Test A |
| C0594:78 | Brake Booster Motor 'A' Performance: Alignment Or Adjustment Incorrect | GO to Pinpoint Test CP |
| C0594:92 | Brake Booster Motor 'A' Performance: Performance Or Incorrect Operation | GO to Pinpoint Test CP |
| C05CC:00 | Brake Master Cylinder Piston Position Sensor 'A' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Z |
| C05CF:00 | Brake Master Cylinder Piston Position Sensor 'B' Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test Z |
| C1013:09 | Brake System Pressure: Component Failures | GO to Pinpoint Test CO |
| C1013:7A | Brake System Pressure: Fluid Leak Or Seal Failure | GO to Pinpoint Test CO |
| C1013:92 | Brake System Pressure: Performance Or Incorrect Operation | GO to Pinpoint Test CO |
| C101F:49 | Generic Valve Failure: Internal Electronic Failure | GO to Pinpoint Test Y |
| C1020:00 | Brake System Fill Not Complete: No Sub Type Information | GO to Pinpoint Test H |
| C102E:48 | Stability Control System: Supervision Software Failure | GO to Pinpoint Test Z |
| C1109:24 | Vehicle Dynamics Control Switch: Signal Stuck High | GO to Pinpoint Test E |
| C1A08:1C | Pressure Sensor Supply: Circuit Voltage Out Of Range | GO to Pinpoint Test Y |
| C1A95:01 | Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test M |
| C1A95:01 | Wheel Speed Sensor: General Electrical Failure | GO to Pinpoint Test N |
| C1A95:64 | Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test AB |
| P05D3:86 | Driver Mode Select Switch 'A' Range/Performance: Signal Invalid | GO to Pinpoint Test BM |
| P0604:8F | Internal Control Module Random Access Memory (RAM) Error: Erratic | GO to Pinpoint Test Z |
| U0100:00 | Lost Communication With ECM/PCM 'A': No Sub Type Information | GO to Pinpoint Test AI |
| U0102:00 | Lost Communication with Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test AV |
| U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test BR |
| U0131:00 | Lost Communication With Power Steering Control Module 'A': No Sub Type Information | GO to Pinpoint Test AE |
| U0136:00 | Lost Communication With Differential Control Module - Rear: No Sub Type Information | GO to Pinpoint Test V |
| U0137:00 | Lost Communication With Trailer Brake Control Module: No Sub Type Information | GO to Pinpoint Test S |
| U0138:00 | Lost Communication with All Terrain Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| U0146:00 | Lost Communication With Serial Data Gateway 'A': No Sub Type Information | GO to Pinpoint Test CI |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AR |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test CE |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BQ |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CL |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AI |
| U0401:64 | Invalid Data Received from ECM/PCM A: Signal Plausibility Failure | GO to Pinpoint Test AI |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test AI |
| U0402:86 | Invalid Data Received from TCM: Signal Invalid | GO to Pinpoint Test AI |
| U0403:00 | Invalid Data Received From Transfer Case Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0420:00 | Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information | GO to Pinpoint Test AE |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test D |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | GO to Pinpoint Test AR |
| U0424:86 | Invalid Data Received From HVAC Control Module: Signal Invalid | GO to Pinpoint Test CE |
| U0439:00 | Invalid Data Received From All Terrain Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0439:86 | Invalid Data Received From All Terrain Control Module: Signal Invalid | GO to Pinpoint Test BM |
| U0452:02 | Invalid Data Received From Restraints Control Module: General Signal Failure | GO to Pinpoint Test BH |
| U0452:41 | Invalid Data Received From Restraints Control Module: General Checksum Failure | GO to Pinpoint Test BH |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test BH |
| U053B:00 | Invalid Data Received From Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BQ |
| U0554:86 | Invalid Data Received From Accessory Protocol Interface Module: Signal Invalid | GO to Pinpoint Test CL |
| U2001:00 | Reduced System Function: No Sub Type Information | GO to Pinpoint Test G |
| U2017:57 | Control Module Software #2: Invalid/Incompatible Software Component | GO to Pinpoint Test Z |
| U2017:93 | Control Module Software #2: No Operation | GO to Pinpoint Test Z |
| U2018:57 | Control Module Software #3: Invalid/Incompatible Software Component | GO to Pinpoint Test Z |
| U202B:61 | In-Use Application Signing Key: Signal Calculation Failure | GO to Pinpoint Test Z |
| U202B:62 | In-Use Application Signing Key: Signal Compare Failure | GO to Pinpoint Test Z |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test Z |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test Z |
| U2107:00 | Collision Mitigation By Braking: No Sub Type Information | GO to Pinpoint Test R |
| U2107:68 | Collision Mitigation By Braking: Event Information | GO to Pinpoint Test AQ |
| U2108:68 | Adaptive Cruise Control: Event Information | GO to Pinpoint Test AQ |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test Z |
| U3000:00 | Control Module: No Sub Type Information | GO to Pinpoint Test Y |
| U3000:04 | Control Module: System Internal Failures | GO to Pinpoint Test Y |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test Y |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test Y |
| U3000:45 | Control Module: Program Memory Failure | GO to Pinpoint Test Y |
| U3000:47 | Control Module: Watchdog/Safety μC Failure | GO to Pinpoint Test Y |
| U3000:48 | Control Module: Supervision Software Failure | GO to Pinpoint Test Y |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test Y |
| U3000:4B | Control Module: Over Temperature | GO to Pinpoint Test Y |
| U3000:52 | Control Module: Not Activated | GO to Pinpoint Test Y |
| U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test Y |
| U3001:68 | Control Module Improper Shutdown Performance: Event Information | GO to Pinpoint Test T |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test AF |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test F |
| U300A:29 | Ignition Switch: Signal Invalid | GO to Pinpoint Test A |