| ABS |
C0020:11 |
ABS Pump Motor Control: Circuit Short To Ground |
GO to Pinpoint Test H |
| ABS |
C0020:12 |
ABS Pump Motor Control: Circuit Short To Battery |
GO to Pinpoint Test H |
| ABS |
C0020:13 |
ABS Pump Motor Control: Circuit Open |
GO to Pinpoint Test H |
| ABS |
C0020:49 |
ABS Pump Motor Control: Internal Electronic Failure |
GO to Pinpoint Test H |
| ABS |
C0020:71 |
ABS Pump Motor Control: Actuator Stuck |
GO to Pinpoint Test H |
| ABS |
C0030:07 |
Left Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0031:01 |
Left Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| ABS |
C0031:07 |
Left Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0031:2F |
Left Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| ABS |
C0031:4A |
Left Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| ABS |
C0031:64 |
Left Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| ABS |
C0033:07 |
Right Front Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0034:01 |
Right Front Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test M |
| ABS |
C0034:07 |
Right Front Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0034:2F |
Right Front Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| ABS |
C0034:4A |
Right Front Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| ABS |
C0034:64 |
Right Front Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| ABS |
C0036:07 |
Left Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0037:01 |
Left Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| ABS |
C0037:07 |
Left Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C0037:2F |
Left Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| ABS |
C0037:4A |
Left Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| ABS |
C0037:64 |
Left Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| ABS |
C0039:07 |
Right Rear Tone Wheel: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C003A:01 |
Right Rear Wheel Speed Sensor: General Electrical Failure |
GO to Pinpoint Test N |
| ABS |
C003A:07 |
Right Rear Wheel Speed Sensor: Mechanical Failures |
GO to Pinpoint Test AB |
| ABS |
C003A:2F |
Right Rear Wheel Speed Sensor: Signal Erratic |
GO to Pinpoint Test AB |
| ABS |
C003A:4A |
Right Rear Wheel Speed Sensor: Incorrect Component Installed |
GO to Pinpoint Test AL |
| ABS |
C003A:64 |
Right Rear Wheel Speed Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AB |
| ABS |
C0040:64 |
Brake Pedal Switch 'A': Signal Plausibility Failure |
GO to Pinpoint Test AC |
| ABS |
C0044:49 |
Brake Pressure Sensor 'A': Internal Electronic Failure |
GO to Pinpoint Test AM |
| ABS |
C0044:51 |
Brake Pressure Sensor 'A': Not Programmed |
GO to Pinpoint Test AM |
| ABS |
C0044:64 |
Brake Pressure Sensor 'A': Signal Plausibility Failure |
GO to Pinpoint Test AM |
| ABS |
C0044:8F |
Brake Pressure Sensor 'A': Erratic |
GO to Pinpoint Test AM |
| ABS |
C0047:1C |
Brake Booster Pressure Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test CO |
| ABS |
C0047:64 |
Brake Booster Pressure Sensor: Signal Plausibility Failure |
GO to Pinpoint Test CO |
| ABS |
C0049:01 |
Brake Fluid Level: General Electrical Failure |
GO to Pinpoint Test I |
| ABS |
C0049:7A |
Brake Fluid Level: Fluid Leak or Seal Failure |
GO to Pinpoint Test L |
| ABS |
C0049:7B |
Brake Fluid Level: Low Fluid Level |
GO to Pinpoint Test I |
| ABS |
C0051:64 |
Steering Wheel Position Sensor: Signal Plausibility Failure |
GO to Pinpoint Test LA |
| ABS |
C0051:67 |
Steering Wheel Position Sensor: Signal Incorrect After Event |
GO to Pinpoint Test LA |
| ABS |
C0051:85 |
Steering Wheel Position Sensor: Signal Above Allowable Range |
GO to Pinpoint Test LA |
| ABS |
C0051:86 |
Steering Wheel Position Sensor: Signal Invalid |
GO to Pinpoint Test LA |
| ABS |
C0061:28 |
Lateral Acceleration Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure |
GO to Pinpoint Test AG |
| ABS |
C0061:64 |
Lateral Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| ABS |
C0062:54 |
Longitudinal Acceleration Sensor: Missing Calibration |
GO to Pinpoint Test AN |
| ABS |
C0062:64 |
Longitudinal Acceleration Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| ABS |
C0063:28 |
Yaw Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure |
GO to Pinpoint Test AG |
| ABS |
C0063:64 |
Yaw Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| ABS |
C0064:28 |
Roll Rate Sensor: Signal Bias Level Out of Range / Zero Adjustment Failure |
GO to Pinpoint Test AG |
| ABS |
C0064:64 |
Roll Rate Sensor: Signal Plausibility Failure |
GO to Pinpoint Test AG |
| ABS |
C0078:56 |
Tire Diameter: Invalid / Incompatible Configuration |
GO to Pinpoint Test ZA |
| ABS |
C052E:A2 |
ABS Pump Motor Control Circuit Low: System Voltage Low |
GO to Pinpoint Test H |
| ABS |
C0594:12 |
Brake Booster Motor 'A' Performance: Circuit Short To Battery |
GO to Pinpoint Test CP |
| ABS |
C0594:78 |
Brake Booster Motor 'A' Performance: Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CP |
| ABS |
C0594:92 |
Brake Booster Motor 'A' Performance: Performance or Incorrect Operation |
GO to Pinpoint Test CP |
| ABS |
C0596:00 |
Brake Booster Motor 'A' Current Sensor Circuit Range/Performance: No Sub Type Information |
GO to Pinpoint Test CP |
| ABS |
C1013:09 |
Brake System Pressure: Component Failures |
GO to Pinpoint Test CO |
| ABS |
C1013:7A |
Brake System Pressure: Fluid Leak or Seal Failure |
GO to Pinpoint Test CO |
| ABS |
C1013:7C |
Brake System Pressure: Slow Response |
GO to Pinpoint Test CO |
| ABS |
C1013:92 |
Brake System Pressure: Performance or Incorrect Operation |
GO to Pinpoint Test CO |
| ABS |
C1018:61 |
Regenerative Braking: Signal Calculation Failure |
GO to Pinpoint Test Z |
| ABS |
C1019:29 |
Linear Actuator Control (LAC): Signal Invalid |
GO to Pinpoint Test CO |
| ABS |
C1019:74 |
Linear Actuator Control (LAC): Actuator Slipping |
GO to Pinpoint Test CO |
| ABS |
C1019:78 |
Linear Actuator Control (LAC): Alignment Or Adjustment Incorrect |
GO to Pinpoint Test CO |
| ABS |
C1019:92 |
Linear Actuator Control (LAC): Performance or Incorrect Operation |
GO to Pinpoint Test CO |
| ABS |
C101F:46 |
Generic Valve Failure: Calibration / Parameter Memory Failure |
GO to Pinpoint Test Z |
| ABS |
C101F:49 |
Generic Valve Failure: Internal Electronic Failure |
GO to Pinpoint Test Z |
| ABS |
C1020:00 |
Brake System Fill Not Complete: No Sub Type Information |
GO to Pinpoint Test C |
| ABS |
C1109:64 |
Vehicle Dynamics Control Switch: Signal Plausibility Failure |
GO to Pinpoint Test O |
| ABS |
C1137:00 |
Reverse gear switch: No Sub Type Information |
GO to Pinpoint Test K |
| ABS |
P0562:16 |
System Voltage Low: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| ABS |
P0563:17 |
System Voltage High: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| ABS |
P1177:64 |
Synchronization: Signal Plausibility Failure |
GO to Pinpoint Test Y |
| ABS |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test AI |
| ABS |
U0100:82 |
Lost Communication With ECM/PCM 'A': Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test AI |
| ABS |
U0100:83 |
Lost Communication With ECM/PCM 'A': Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AI |
| ABS |
U0100:87 |
Lost Communication With ECM/PCM 'A': Missing Message |
GO to Pinpoint Test AI |
| ABS |
U0102:00 |
Lost Communication with Transfer Case Control Module: No Sub Type Information |
GO to Pinpoint Test AU |
| ABS |
U0103:00 |
Lost Communication With Gear Shift Control Module A: No Sub Type Information |
GO to Pinpoint Test AV |
| ABS |
U011D:87 |
Lost Communication With All Wheel Drive Control Module: Missing Message |
GO to Pinpoint Test BX |
| ABS |
U0122:00 |
Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test BR |
| ABS |
U0126:87 |
Lost Communication With Steering Angle Sensor Module: Missing Message |
GO to Pinpoint Test J |
| ABS |
U0131:82 |
Lost Communication With Power Steering Control Module 'A': Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test AE |
| ABS |
U0131:83 |
Lost Communication With Power Steering Control Module 'A': Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AE |
| ABS |
U0131:87 |
Lost Communication With Power Steering Control Module 'A': Missing Message |
GO to Pinpoint Test AE |
| ABS |
U0132:00 |
Lost Communication With Suspension Control Module 'A': No Sub Type Information |
GO to Pinpoint Test CJ |
| ABS |
U0138:00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test BM |
| ABS |
U0138:86 |
Lost Communication with All Terrain Control Module: Signal Invalid |
GO to Pinpoint Test BM |
| ABS |
U0138:87 |
Lost Communication with All Terrain Control Module: Missing Message |
GO to Pinpoint Test BM |
| ABS |
U0140:87 |
Lost Communication With Body Control Module: Missing Message |
GO to Pinpoint Test D |
| ABS |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test BP |
| ABS |
U0146:87 |
Lost Communication With Serial Data Gateway 'A': Missing Message |
GO to Pinpoint Test BP |
| ABS |
U0151:00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| ABS |
U0151:82 |
Lost Communication With Restraints Control Module: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test BH |
| ABS |
U0151:83 |
Lost Communication With Restraints Control Module: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test BH |
| ABS |
U0151:87 |
Lost Communication With Restraints Control Module: Missing Message |
GO to Pinpoint Test BH |
| ABS |
U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test AR |
| ABS |
U0155:87 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message |
GO to Pinpoint Test AR |
| ABS |
U0159:87 |
Lost Communication With Parking Assist Control Module 'A': Missing Message |
GO to Pinpoint Test BY |
| ABS |
U0164:00 |
Lost Communication With HVAC Control Module 'A': No Sub Type Information |
GO to Pinpoint Test CE |
| ABS |
U0164:87 |
Lost Communication With HVAC Control Module 'A': Missing Message |
GO to Pinpoint Test CE |
| ABS |
U0212:86 |
Lost Communication With Steering Column Control Module: Signal Invalid |
GO to Pinpoint Test BV |
| ABS |
U0212:87 |
Lost Communication With Steering Column Control Module: Missing Message |
GO to Pinpoint Test BV |
| ABS |
U0232:87 |
Lost Communication With Side Obstacle Detection Control Module 'A': Missing Message |
GO to Pinpoint Test BZ |
| ABS |
U0233:87 |
Lost Communication With Side Obstacle Detection Control Module 'B': Missing Message |
GO to Pinpoint Test BZ |
| ABS |
U023A:87 |
Lost Communication With Image Processing Module A: Missing Message |
GO to Pinpoint Test BQ |
| ABS |
U023B:00 |
Lost Communication With Image Processing Module B: No Sub Type Information |
GO to Pinpoint Test CK |
| ABS |
U023B:87 |
Lost Communication With Image Processing Module B: Missing Message |
GO to Pinpoint Test CK |
| ABS |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test CL |
| ABS |
U0293:00 |
Lost Communication With Hybrid/EV Powertrain Control Module 'A': No Sub Type Information |
GO to Pinpoint Test CM |
| ABS |
U0300:51 |
Internal Control Module Software Incompatibility: Not Programmed |
GO to Pinpoint Test Z |
| ABS |
U0401:81 |
Invalid Data Received from ECM/PCM A: Invalid Serial Data Received |
GO to Pinpoint Test AI |
| ABS |
U0401:82 |
Invalid Data Received from ECM/PCM A: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test AI |
| ABS |
U0401:83 |
Invalid Data Received from ECM/PCM A: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AI |
| ABS |
U0401:86 |
Invalid Data Received from ECM/PCM A: Signal Invalid |
GO to Pinpoint Test AI |
| ABS |
U0402:00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test AI |
| ABS |
U0404:86 |
Invalid Data Received from Gear Shift Control Module A: Signal Invalid |
GO to Pinpoint Test AV |
| ABS |
U0422:86 |
Invalid Data Received From Body Control Module: Signal Invalid |
GO to Pinpoint Test D |
| ABS |
U0424:86 |
Invalid Data Received from HVAC Control Module 'A': Signal Invalid |
GO to Pinpoint Test CE |
| ABS |
U0428:82 |
Invalid Data Received From Steering Angle Sensor Module: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test J |
| ABS |
U0428:83 |
Invalid Data Received From Steering Angle Sensor Module: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test J |
| ABS |
U0452:00 |
Invalid Data Received From Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test BH |
| ABS |
U0452:86 |
Invalid Data Received From Restraints Control Module: Signal Invalid |
GO to Pinpoint Test BH |
| ABS |
U053B:82 |
Invalid Data Received From Image Processing Module A: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test BQ |
| ABS |
U053B:83 |
Invalid Data Received From Image Processing Module A: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test BQ |
| ABS |
U053B:86 |
Invalid Data Received From Image Processing Module A: Signal Invalid |
GO to Pinpoint Test BQ |
| ABS |
U0554:86 |
Invalid Data Received From Accessory Protocol Interface Module: Signal Invalid |
GO to Pinpoint Test CL |
| ABS |
U0594:86 |
Invalid Data Received From Hybrid/EV Powertrain Control Module 'A': Signal Invalid |
GO to Pinpoint Test CM |
| ABS |
U2001:00 |
Reduced System Function: No Sub Type Information |
GO to Pinpoint Test B |
| ABS |
U2017:57 |
Control Module Software #2: Invalid / Incompatible Software Component |
GO to Pinpoint Test Z |
| ABS |
U2017:93 |
Control Module Software #2: No Operation |
GO to Pinpoint Test Z |
| ABS |
U2018:57 |
Control Module Software #3: Invalid / Incompatible Software Component |
GO to Pinpoint Test Z |
| ABS |
U2024:51 |
Control Module Cal-Config Data: Not Programmed |
GO to Pinpoint Test Z |
| ABS |
U2024:57 |
Control Module Cal-Config Data: Invalid / Incompatible Software Component |
GO to Pinpoint Test Z |
| ABS |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test Z |
| ABS |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test Z |
| ABS |
U2107:00 |
Collision Mitigation By Braking: No Sub Type Information |
GO to Pinpoint Test R |
| ABS |
U2107:68 |
Collision Mitigation By Braking: Event Information |
GO to Pinpoint Test AQ |
| ABS |
U2108:68 |
Adaptive Cruise Control: Event Information |
GO to Pinpoint Test R |
| ABS |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test Z |
| ABS |
U3000:00 |
Control Module: No Sub Type Information |
GO to Pinpoint Test Y |
| ABS |
U3000:04 |
Control Module: System Internal Failure |
GO to Pinpoint Test Y |
| ABS |
U3000:41 |
Control Module: General Checksum Failure |
GO to Pinpoint Test Y |
| ABS |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test Y |
| ABS |
U3000:4B |
Control Module: Over Temperature |
GO to Pinpoint Test Y |
| ABS |
U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test Y |
| ABS |
U3001:68 |
Control Module Improper Shutdown Performance: Event Information |
GO to Pinpoint Test G |
| ABS |
U3002:51 |
Vehicle Identification Number: Not Programmed |
GO to Pinpoint Test AF |
| ABS |
U3002:62 |
Vehicle Identification Number: Signal Compare Failure |
GO to Pinpoint Test AF |
| ABS |
U3003:16 |
Battery Voltage: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| ABS |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test F |
| ABS |
U300A:29 |
Ignition Switch: Signal Invalid |
GO to Pinpoint Test A |
| ABS |
U3012:00 |
Control Module Improper Wake-up Performance: No Sub Type Information |
GO to Pinpoint Test E |
| ATCM |
P05D3:86 |
Driver Mode Select Switch 'A' Range/Performance: Signal Invalid |
GO to Pinpoint Test OB |
| PCM |
P05FF:00 |
Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information |
GO to Pinpoint Test CO |
| SASM |
B1016:19 |
Status Switch: Circuit Current Above Threshold |
GO to Pinpoint Test S |
| SASM |
C1B00:1C |
Steering Angle Sensor: Circuit Voltage Out Of Range |
GO to Pinpoint Test S |
| SASM |
C1B00:49 |
Steering Angle Sensor: Internal Electronic Failure |
GO to Pinpoint Test S |
| SASM |
C1B00:54 |
Steering Angle Sensor: Missing Calibration |
GO to Pinpoint Test U |
| SASM |
C1B00:56 |
Steering Angle Sensor: Invalid / Incompatible Configuration |
GO to Pinpoint Test V |
| SASM |
C1B00:62 |
Steering Angle Sensor: Signal Compare Failure |
GO to Pinpoint Test S |
| SASM |
C1B00:64 |
Steering Angle Sensor: Signal Plausibility Failure |
GO to Pinpoint Test S |
| SASM |
C1B00:81 |
Steering Angle Sensor: Invalid Serial Data Received |
GO to Pinpoint Test S |
| SASM |
C1B00:85 |
Steering Angle Sensor: Signal Above Allowable Range |
GO to Pinpoint Test S |
| SASM |
C1B00:95 |
Steering Angle Sensor: Incorrect Assembly |
GO to Pinpoint Test W |
| SASM |
U0001:88 |
High Speed CAN Communication Bus: Bus Off |
GO to Pinpoint Test X |
| SASM |
U0100:00 |
Lost Communication With ECM/PCM 'A': No Sub Type Information |
GO to Pinpoint Test AW |
| SASM |
U0121:00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AX |
| SASM |
U0122:00 |
Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test AY |
| SASM |
U0130:00 |
Lost Communication With Steering Effort Control Module: No Sub Type Information |
GO to Pinpoint Test AZ |
| SASM |
U0140:00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test T |
| SASM |
U0146:00 |
Lost Communication With Serial Data Gateway 'A': No Sub Type Information |
GO to Pinpoint Test BA |
| SASM |
U0155:00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test BB |
| SASM |
U0253:00 |
Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test BC |
| SASM |
U0401:00 |
Invalid Data Received from ECM/PCM A: No Sub Type Information |
GO to Pinpoint Test AW |
| SASM |
U0401:81 |
Invalid Data Received from ECM/PCM A: Invalid Serial Data Received |
GO to Pinpoint Test AW |
| SASM |
U0401:82 |
Invalid Data Received from ECM/PCM A: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test AW |
| SASM |
U0401:83 |
Invalid Data Received from ECM/PCM A: Value Of Signal Protection Calculation Incorrect |
GO to Pinpoint Test AW |
| SASM |
U0415:00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module 'A': No Sub Type Information |
GO to Pinpoint Test AX |
| SASM |
U0416:00 |
Invalid Data Received From Vehicle Dynamics Control Module: No Sub Type Information |
GO to Pinpoint Test AY |
| SASM |
U0419:81 |
Invalid Data Received From Steering Effort Control Module: Invalid Serial Data Received |
GO to Pinpoint Test AZ |
| SASM |
U0422:00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test T |
| SASM |
U0423:00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test BB |
| SASM |
U0423:82 |
Invalid Data Received from Instrument Panel Cluster Control Module: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test BB |
| SASM |
U0425:00 |
Invalid Data Received From Auxiliary Heater Control Module: No Sub Type Information |
GO to Pinpoint Test DA |
| SASM |
U0554:00 |
Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information |
GO to Pinpoint Test BC |
| SASM |
U0554:82 |
Invalid Data Received From Accessory Protocol Interface Module: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test BC |
| SASM |
U0556:82 |
Invalid Data Received From Front Display Interface Module: Alive / Sequence Counter Incorrect / Not Updated |
GO to Pinpoint Test CZ |
| SASM |
U1000:00 |
Solid State Driver Protection Active -Driver Disabled: No Sub Type Information |
GO to Pinpoint Test S |
| SASM |
U2001:98 |
Reduced System Function: Component Or System Over Temperature |
GO to Pinpoint Test S |
| SASM |
U2002:98 |
Switch: Component Or System Over Temperature |
GO to Pinpoint Test S |
| SASM |
U2016:47 |
Control Module Main Software: Watchdog / Safety μC Failure |
GO to Pinpoint Test Z |
| SASM |
U2100:00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test Z |
| SASM |
U2101:00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test Z |
| SASM |
U210A:02 |
Temperature Sensor: General Signal Failure |
GO to Pinpoint Test S |
| SASM |
U2200:00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test Z |
| SASM |
U3000:1E |
Control Module: Circuit Resistance Out of Range |
GO to Pinpoint Test S |
| SASM |
U3000:42 |
Control Module: General Memory Failure |
GO to Pinpoint Test S |
| SASM |
U3000:45 |
Control Module: Program Memory Failure |
GO to Pinpoint Test S |
| SASM |
U3000:49 |
Control Module: Internal Electronic Failure |
GO to Pinpoint Test S |
| SASM |
U3000:96 |
Control Module: Component Internal Failure |
GO to Pinpoint Test AA |
| SASM |
U3003:17 |
Battery Voltage: Circuit Voltage Above Threshold |
GO to Pinpoint Test BE |
| SASM |
U3011:13 |
Ignition Input Off: Circuit Open |
GO to Pinpoint Test BL |