Common Specifications & Procedures
AVIATOR (HYBRID/EXCEPT HYBRID) COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||||
|---|---|---|---|---|---|
| Air Conditioning | |||||
| Service | SPECIFICATIONS - (3.0L EcoBoost) | ||||
| Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION - (3.0L EcoBoost) | ||||
| Axle Nut/Hub Nut | 98 lb.ft (133 Nm) | ||||
| Battery | |||||
| Specifications | SPECIFICATIONS - (3.0L EcoBoost) | ||||
| Brakes | |||||
| Bleeding Sequence | Brake System Pressure Bleeding - (3.0L EcoBoost) | ||||
| Front Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION - (3.0L EcoBoost) | ||||
| Rear Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION - (3.0L EcoBoost) | ||||
| Charging | |||||
| Generator w/Torque | |||||
| For removal and installation, refer to REMOVAL AND INSTALLATION - (3.0L EcoBoost) | Generator Bolt 35 lb.ft (47.5 Nm) Generator Nut: 35 lb.ft (47.5 Nm) Generator Stud 71 lb.in (8 Nm) |
||||
| Drive Belts | |||||
| Adjustment | Accessory Drive - (3.0L EcoBoost) |
||||
| Belt Routing | Accessory Drive - Component Location - (3.0L EcoBoost) |
||||
| Engine Cooling | |||||
| General Service Specifications | SPECIFICATIONS (3.0L EcoBoost) |
||||
| Pressure Relief Cap | 145 kPa (21 psi) | ||||
| Thermostat R & I | Thermostat - (3.0L EcoBoost) |
||||
| Water Pump R & I | Coolant Pump - (3.0L EcoBoost) |
||||
| Engine Mechanical | |||||
| Compression | For Except Hybrid, refer to: SPECIFICATIONS - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Oil pressure (hot @ 1, 500 rpm) | 16.0 -24.7 psi (110 -170 kPa) | ||||
| Overhaul | For Except Hybrid, refer to: SPECIFICATIONS - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Torque | For Except Hybrid, refer to: REMOVAL AND INSTALLATION - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||||
| Flywheel/Flex Plate Torque | |||||
| For Except Hybrid tightening sequence, refer to: Flexplate - (3.0L EcoBoost) For Hybrid tightening sequence, refer to: |
3.0L EcoBoost Torque: 59 lb.ft (80 Nm) 3.0L EcoBoost Hybrid Stage 1: 22 lb.ft (30 Nm) Stage 2: 45° |
||||
| Fuel System | |||||
| Fuel Filter Location | Located in fuel tank as part of the fuel pump module. | ||||
| Fuel Filter R & I | For Except Hybrid, refer to: Fuel Pump and Sender Unit - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Pressure Release Procedure | For Except Hybrid, refer to: Fuel System Pressure Release - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Fuel Pressure Test Procedure | For Except Hybrid, refer to: Fuel System Pressure Check - (3.0L EcoBoost) For Hybrid, refer to: |
||||
| Ignition | |||||
| Spark Plug | CYFS 12Y PT | ||||
| Torque: | 133 lb.in (15 Nm) | ||||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||||
| Starting | |||||
| Starter | Specifications - (3.0L EcoBoost) |
||||
| Torque | |||||
| For removal and installation, refer to Starter Motor - (3.0L EcoBoost) For removal and installation, refer to |
Starter Motor Stud bolts: 35 lb.ft (47.5 Nm) | ||||
| Wheel Alignment | |||||
| Adjustment Specifications | SPECIFICATIONS | ||||
| Torque | Refer to the appropriate procedure in GENERAL PROCEDURES | ||||
| Wheel & Tire | |||||
| Wheel Lug Nut Torque | For tightening sequence, refer to Wheel and Tire
. 150 lb.ft (204 Nm) |
||||