Cruise Control Module
NOTE:
On Protege 1.5L, cruise control module and actuator are an integral unit. Cruise control module may be referred to as cruise control actuator.
- On MPV and Protege 1.8L, locate cruise control module behind right kick panel. On Protege 1.5L locate cruise control module (actuator) at right rear corner of engine compartment. On all models, leave cruise control module harness connector attached unless other wise specified. Using DVOM, backprobe at specified terminals of cruise control module harness connector while performing appropriate test condition. See appropriate CRUISE CONTROL MODULE PIN VOLTAGE CHART table. See Fig 1 or Fig 2
. Go to next step.
- If voltage measurements or continuity measurements are not as specified, check related components and wiring. See WIRINGS DIAGRAMS and appropriate component tests. If related components and wiring are okay, but system is still not functioning properly, replace cruise control module.
CRUISE CONTROL MODULE PIN VOLTAGE CHART (MPV)
| Terminal (Signal) |
Test Condition |
Value |
| A (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| B (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| C (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| D (Indicator Light Output) |
Ignition On |
Battery Voltage |
| " |
Ignition LOCK Or ACC |
0 Volts |
| E (Main Switch) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| G (PCM O/D Off) |
Ignition On |
Battery Voltage |
| " |
Ignition LOCK Or ACC |
0 Volts |
| H (Actuator Power Supply) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| I (Data Link Connector) |
N/A |
N/A |
| J (TR Switch) |
Ignition On; Main Switch On; Gear Selector Not In Park Or Neutral |
Battery Voltage |
| " |
Ignition On; Main Switch Off; Gear Selector In Park Or Neutral |
0 Volts |
| M (Brake Light Switch) |
Brake Pedal Depressed |
Battery Voltage |
| " |
Brake Pedal Released |
0 Volts |
| N (Cruise Control Switch) |
Ignition On; SET/COAST Switch Depressed |
1.5 Volts |
| " |
Ignition On; RESUME/ACCEL Switch Depressed |
3.1 Volts |
| " |
Ignition On; Other |
5 Volts |
| O (Cruise Brake Switch) |
Ignition On; Main Switch On; Brake Pedal Released |
Battery Voltage |
| " |
Ignition On; Main Switch Off; Brake Pedal Depressed |
0 Volts |
| P (Vehicle Speed Sensor) |
Ignition On; Main Switch On; Rear Tires Rotating |
Alterating Between 0-5 Volts AC |
| T (Ground) |
At All Times |
Continuity To Ground |
CRUISE CONTROL MODULE PIN VOLTAGE CHART (PROTEGE 1.8L)
| Terminal (Signal) |
Test Condition |
Value |
| A (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| B (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| C (Actuator Control) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| D (Indicator Light Output) |
Ignition On |
Battery Voltage |
| " |
Ignition LOCK Or ACC |
0 Volts |
| E (Main Switch) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| G (PCM O/D Off) |
Ignition On |
Battery Voltage |
| " |
Ignition LOCK Or ACC |
0 Volts |
| H (Cruise Brake Switch) |
Ignition On; Main Switch On |
Battery Voltage |
| " |
Ignition On; Main Switch Off |
0 Volts |
| I (Data Link Connector) |
N/A |
N/A |
| J (Clutch Switch - M/T) |
Ignition On; Main Switch On; Clutch Pedal Released |
Battery Voltage |
| " |
Ignition On; Main Switch Off; Clutch Pedal Depressed |
0 Volts |
| J (TR Switch - A/T) |
Ignition On; Main Switch On; Gear Selector Not In Park Or Neutral |
Battery Voltage |
| " |
Ignition On; Main Switch Off; Gear Selector In Park Or Neutral |
0 Volts |
| M (Brake Light Switch) |
Brake Pedal Depressed |
Battery Voltage |
| " |
Brake Pedal Released |
0 Volts |
| N (Cruise Control Switch) |
SET/COAST Switch Depressed |
240 Ohms |
| " |
RESUME/ACCEL Switch Depressed |
910 Ohms |
| " |
CANCEL Switch Depressed |
0 Ohms |
| O (Cruise Brake Switch) |
Ignition On; Main Switch On; Brake Pedal Released |
Battery Voltage |
| " |
Ignition On; Main Switch Off; Brake Pedal Depressed |
0 Volts |
| P (Vehicle Speed Sensor) |
Ignition On; Main Switch On; Front Tires Rotating |
Alterating Between 0-5 Volts AC |
| T (Ground) |
At All Times |
Continuity To Ground |
CRUISE CONTROL MODULE PIN VOLTAGE CHART (PROTEGE 1.5L)
| Terminal (Signal) |
Test Condition |
Value |
| A (Indicator Light Output) |
Ignition On |
Battery Voltage |
| " |
Ignition Lock Or ACC |
0 Volts |
| B (PCM O/D Off) |
Ignition On |
Battery Voltage |
| " |
Ignition LOCK Or ACC |
0 Volts |
| C (Vehicle Speed Sensor) |
Ignition On; Main Switch On; Front Tires Rotating |
Alterating Between 0-5 Volts AC |
| D (Brake Light Switch) |
Brake Pedal Depressed |
Battery Voltage |
| " |
Brake Pedal Released |
0 Volts |
| E (Cruise Control Switch) . SET/COAST Switch Depressed |
240 Ohms |
" |
| RESUME/ACCEL Switch Depressed |
910 Ohms |
" |
| CANCEL Switch Depressed |
0 Ohms |
F (Clutch Switch - M/T) |
| Clutch Pedal Depressed |
Continuity To Ground |
" |
| Clutch Pedal Released |
No Continuity To Ground |
F (Inhibitor Switch - A/T) |
| Gear Selector In Park Or Neutral |
Continuity To Ground |
" |
| Gear Selector Not In Park Or Neutral |
No Continuity To Ground |
G (Power Supply) |
| Ignition On |
Battery Voltage |
" |
| Ignition LOCK Or ACC |
0 Volts |
H (Main Switch) |
| Ignition On; Main Switch On |
Battery Voltage |
" |
| Ignition On; Main Switch Off |
0 Volts |
I (Cruise Brake Switch) |
| Brake Pedal Released |
Battery Voltage |
" |
| Brake Pedal Depressed |
0 Volts |
J (Ground) |
| At All Times |
Continuity To Ground |
- |
Courtesy of MAZDA MOTORS CORP.
Courtesy of MAZDA MOTORS CORP.