LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2007 >> B3000 Base, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Symptom Troubleshooting - Engine (1 Of 4) >> Diagnostic Monitoring Test Results Table >> Notes
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Monitoring Test Results Table: Notes

DIAGNOSTIC MONITORING TEST RESULTS

Module ID h (1) Test ID h (1) Component ID h (1) Test Description
      Oxygen Sensor Monitor (01-OF) 
10 01 11 Sensor voltage amplitude - bank 1, sensor 1
10 01 21 Sensor voltage amplitude - bank 2, sensor 1
10 02 11 Upstream static shift, lean shift on EGO 11
10 02 11 Upstream static shift, rich shift on EGO 11
10 02 21 Upstream static shift, lean shift on EGO 21
10 02 21 Upstream static shift, rich shift on EGO 21
10 03 01 Upstream switchpoint
10 03 02 Downstream switchpoint
      Catalyst Monitor (10-1F) 
10 10 11 Rear to front switch ratio test - bank 1 test
10 10 21 Rear to front switch radio test - bank 2 test
      Evaporative Monitor (21-2F) 
10 21 (2) 00 Fuel tank pressure test - low
10 21 (2) 00 Fuel tank pressure test - high
10 22 (2) 00 Evap-phase 2 change in pressure test
10 23 (2) 00 Evap-phase 4 change in pressure too large
10 24 (2) 00 Evap-phase 4 change in pressure too small
10 25 (2) 00 Evap-phase 4 pressure build test-upper limit
10 26 00 Phase 0 initial tank vacuum and minimum limit
10 26 00 Phase 0 initial tank vacuum and maximum limit
10 27 00 Phase 2 0.040" cruise leak check vacuum bleed-up and max 0.04" leak threshold
10 28 00 Phase 2 0.020" cruise leak check vacuum bleed-up and max leak threshold
10 29 00 EVAP-phase 4 change in pressure too small
10 2A 00 Phase 4 vapor generation maximum change in pressure and maximum threshold
10 2B 00 Phase 4 vapor generation maximum absolute pressure and maximum threshold
10 2C 00 Phase 2 0.020" idle leak check vacuum bleed-up and max leak threshold
10 2D 00 Phase 2 0.040" idle leak check vacuum bleed-up and max no-leak threshold
      EGR System Monitor (41-4F) 
10 41 (2) 11 Upstream hose disconnected test
10 41 (2) 12 Downstream hose disconnected test
10 45 20 Stuck open valve test
10 49 30 EGR flow test
10 4B 30 Flow test
      Misfire Monitor (51-5F) 
10 50 00 Total misfires that exceeded threshold
10 51 01 Cylinder #1 misfires that exceeded threshold
10 51 02 Cylinder #2 misfires that exceeded threshold
10 51 03 Cylinder #3 misfires that exceeded threshold
10 51 04 Cylinder #4 misfires that exceeded threshold
10 51 05 Cylinder #5 misfires that exceeded threshold
10 51 06 Cylinder #6 misfires that exceeded threshold
10 52 00 Consecutive cylinder events during active test
10 53 01 Misfire rate per 200 revs for cylinder 1/type A
10 53 02 Misfire rate per 200 revs for cylinder 2/type A
10 53 03 Misfire rate per 200 revs for cylinder 3/type A
10 53 04 Misfire rate per 200 revs for cylinder 4/type A
10 53 05 Misfire rate per 200 revs for cylinder 5/type A
10 53 06 Misfire rate per 200 revs for cylinder 6/type A
10 54 00 Highest misfire rate in 200 rev test/type A
10 55 00 Highest misfire rate in 1, 000 rev test/type B
10 56 00 Misfire monitor trip complete test
(1) hexidecimal
(2) These test IDs are signed values. Scan tool may display them as unsigned.

The conversion is done as follows: If the value is > 32767 then complement (change 0's to 1's and 1's to 0's), add 1 and a negative sign.

Example: 

SIGNED VALUES CONVERSION EXAMPLE

50000= 110000110101000
Complement of 50000= 0011110010101111
  +1
  001111001010000
Signed Value= -15536
scientia non olet · About LEMON Manuals