LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2007 >> B3000 Base, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 16 (Engine Mechanical) >> Torque Specifications
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Torque Specifications

WARNING: This page is about a different car, the 2002 Mazda B3000 and 2001 Mazda B3000. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
A/C Compressor & Power Steering Bracket 38 (51)
Axle Housing Mounting Bolts 49 (66)
Camshsaft Sprocket Bolt 40-51 (55-70)
Clutch Cover Bolts (1) 17-24 (23-32)
Connecting Rod Cap 23-29 (31-39)
Crankshaft Damper Bolt 107 (145)
Crankshaft Main Bearing Cap Bolts 55-63 (75-85)
Crankshaft Pulley Bolt 46 (63)
Crossmember Mounting Bolts 39-53 (53-72)
Cylinder Head Bolts (2)
Stage 1 59 (80)
Stage 2 Loosen 360 Degrees
Stage 3 37 (50)
Stage 4 68 (92)
Drive Belt Tensioner 18-22 (24-31)
Drive Belt Idler Pulley Bolt 30-40 (40-55)
Pinion Flange-To-Front Drive Shaft Bolts 14 (19)
Engine Fan Bolts 17 (23)
Engine Front Cover Bolts 18 (25)
Engine Mount Nuts 80 (109)
Exhaust Manifold (3)
Step 1 8 (10)
Step 2 15-18 (20-25)
Exhaust Manifold To Pipe Nuts 25-33 (34-46)
Flexplate Bolts (4) 59 (80)
Flywheel Bolts 59 (80)
Front Axle Mounting Bolts 49 (66)
Generator Stud Bolts 35 (47)
Heated Oxygen Sensor 27-33 (36-46)
Idle Air Control Valve 8 (11)
Intake Manifold Bolts (Lower) (5) 21 (29)
Knock Sensor 18 (25)
Oil Drain Plug 17 (23)
Oil Indicator Tube Bracket Nut 13 (18)
Oil Pan (6) 9 (12)
Oil Pan Baffle Nuts 24 (32)
Oil Pressure Gauge 8-18 (11-24)
Power Steering Pump Mounting Bolts 35 (48)
Rocker Arm Bolts 24 (32)
Spark Plug 7-15 (9-20)
Starter Motor Bolts 17-20 (22-28)
Suction/Discharge Line Nut 8 (11)
Thermostat Housing Bolts 18 (25)
Transmission-To-Engine Bolts 37-50 (50-68)
Transmission Bolt 64-81 (87-110)
Upper Intake Manifold Support Bracket Stud Bolt 8 (10)
Valve Cover Bolts (7) 9 (12)
Valve Tappets 9 (12)
Water Pump Bracket Bolts 38 (51)
Water Pump Pulley 18 (25)
INCH Lbs. (N.m) 
Air Cleaner Bolt 89 (10)
Block Heater Core Plug 14-16 (1.6-1.8)
Camshaft Position Sensor 26-36 (2.3-3.5)
Coil Mounting Bolts 53 (6)
Crankshaft Position Sensor 89 (10)
Fan Shroud Bolts 62 (7)
Fuel Line Mounting Bolts 89 (10)
Ground Cable 89 (10)
Generator Nut 71 (8)
Ignition Coil Pack Bolts/Studs 53 (6)
Intake Manifold Bolts (Upper) (8) 89 (10)
PCM Connector 53 (6)
Snow Shield Bolt 89 (10)
Starter Motor Terminal Nuts (Larger) 98-115 (11-13)
Starter Motor Terminal Nuts (Smaller) 45-53 (5-6)
Water Pump Bolt 89 (10)
(1) Tighten the clutch cover bolts in a star pattern.
(2) Tighten cylinder head bolts in sequence. See Figure.
(3) Tighten exhaust manifold bolts in sequence. See Figure & Figure .
(4) Tighten the bolts in a criss-cross pattern.
(5) Tighten lower intake manifold bolts in sequence. See Figure.
(6) Hand tighten all bolts before torquing them. Tighten oil pan bolts in sequence. See Figure.
(7) Tighten valve cover bolts in sequence. See Figure.
(8) Tighten upper intake manifold bolts in sequence. See Figure.