PID/DATA monitor table (reference)
WARNING: This page is about a different car, the 2005 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
PID/DATA MONITOR CHART
| Monitor item (Definition) | Unit/Condition | Condition/Specification (Reference) | Action | PCM terminal | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AAT | °C | °F | Ignition switch at ON position: Indicate the ambient air temperature | Inspect IAT sensor. (See INTAKE AIR TEMPERATURE (IAT) SENSOR INSPECTION ) | - | ||||||||||||||||
| AC REQ (A/C switch) | On/Off | A/C switch and fan switch ON at ignition switch ON: On A/C switch OFF at ignition switch ON: Off |
Inspect A/C switch. (See CLIMATE CONTROL UNIT INSPECTION .) | 5(1) 1AC(2) |
|||||||||||||||||
| ACCS (A/C relay) | On/Off | Ignition switch ON: Off A/C switch ON and fan switch ON at idle: On | Inspect following PIDs: RPM, TP, ECT, ACSW. Inspect A/C relay. (See CLIMATE CONTROL UNIT INSPECTION ) | 47(1) 4O(2) |
|||||||||||||||||
| ALTF (Generator field coil control duty value) | % | Ignition switch ON: 0% Idle: 0-100% Just after A/C switch ON and fan switch ON at idle: Duty value rises |
Inspect following PIDs: IAT, ECT, RPM, VPWR, ALTT V. Inspect generator. (See GENERATOR INSPECTION .) |
36(1) 1AD(2) |
|||||||||||||||||
| ALTT V (Generator output voltage) | V | Ignition switch ON: 0 V Idle: Approx. 14.5 V(4) (E/L not operating) | Inspect generator. (See GENERATOR INSPECTION ) | 63(1) 1AA(2) |
|||||||||||||||||
| APP (Accelerator pedal position) | % | AP is released: 0% AP is depressed: 100% |
Inspect following PIDs: APP1, APP2. Inspect accelerator pedal position sensor. (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION ) |
42, 43(1) 2A, 3D(2) |
|||||||||||||||||
| APP1 (Accelerator pedal position) | % | AP is released: 31.0-32.4% AP is depressed: 69.8-81.8% |
Inspect accelerator pedal position sensor. (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION ) |
43(1) 3D(2) |
|||||||||||||||||
| V | AP is released: 1.55-1.62 V AP is depressed: 3.49-4.09 V |
||||||||||||||||||||
| APP2 (Accelerator pedal position) | % | AP is released: 20.2-21.4% AP is depressed: 58.8-70.8% |
Inspect accelerator pedal position sensor. (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION ) |
42(1) 2A(2) |
|||||||||||||||||
| V | AP is released: 1.01-1.07V AP is depressed: 2.94-3.54 V |
||||||||||||||||||||
| ARPMDES (Target engine speed) | RPM | No load: 700 rpm E/L operating: 700 rpm P/S operating: 700 rpm A/C ON: 750 rpm |
Inspect following PIDs: IAT, RPM, MAP, ECT, MAF, TP, INGEAR, ACSW, PSP, ALTT V. Inspect CKP sensor. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION ) |
- | |||||||||||||||||
| B+ (Battery positive voltage) | V | Ignition switch ON: B+ | Inspect main relay. (See RELAY INSPECTION
) Inspect battery. (See BATTERY INSPECTION ) |
86(1) 2Z(2) |
|||||||||||||||||
| BARO (Barometric pressure) | kPa, Bar, psi | Ignition switch ON: Indicate the atmospheric pressure | Inspect BARO sensor. (See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION ) | 37(1) 1G(2) |
|||||||||||||||||
| BOO (Brake switch) | On/Off | Brake pedal depressed: On Brake pedal released: Off |
Inspect brake switch. (See BRAKE SWITCH INSPECTION ) | 56, 82(1) 1K, 3T(2) |
|||||||||||||||||
| BPA (Brake pressure applied switch) | On/Off | Brake pedal depressed: On Brake pedal released: Off |
Inspect brake switch. (See BRAKE SWITCH INSPECTION ) | 56, 82(1) 1K, 3T(2) |
|||||||||||||||||
| CATT11_DSD (Estimated catalytic converter temperature) | °C | °F | Indicate the estimated catalytic converter temperature | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | ||||||||||||||||
| CHRGLP (Generator warning light) | On/Off | Ignition switch ON: On Idle: Off | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| COLP (Refrigerant pressure switch (middle)) | On/Off | Refrigerant pressure switch (middle) ON(5) at idle: ON Refrigerant pressure switch (middle) OFF(6) at idle: OFF |
Inspect refrigerant pressure switch. (See REFRIGERANT PRESSURE SWITCH INSPECTION ) | 30(1) 1Q(2) |
|||||||||||||||||
| CPP(3) (Clutch pedal position) | On/Off | Clutch pedal depressed: On Clutch pedal released: Off |
Inspect clutch switch. (See CLUTCH PEDAL POSITION (CPP) SWITCH INSPECTION ) | 1R | |||||||||||||||||
| CPP/PNP(3) (Shift lever position) | Drive/Neutral | Neutral position: Neutral Others: Drive | Inspect neutral switch. (See NEUTRAL SWITCH INSPECTION ) | 1W | |||||||||||||||||
| DTC_CNT (Number of DTC detected) | - | - | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| ECT (Engine coolant temperature) | °C | °F | Ignition switch at ON position: Indicate the ECT | Inspect ECT sensor. (See ENGINE COOLANT TEMPERATURE (ECT) SENSOR INSPECTION ) | 41(1) 1M(2) |
||||||||||||||||
| V | ECT 20 °C {68 °F}: 3.04-3.14 V ECT 60 °C {140 °F}: 1.29-1.39 V |
||||||||||||||||||||
| EQ_RAT 11(1) (Equivalence ratio (lambda)) | - | Idling after warm-up: Approx. 1 | Perform applicable DTC troubleshooting. (See DTC TABLE ) | 61 | |||||||||||||||||
| EQ_RAT 11_DSD (Front oxygen sensor) | - | Idling after warm-up: Approx. 1 | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| ETC_ACT (Electronic throttle control actual) | ° | Indicate the desired TP by angle | Perform applicable DTC troubleshooting. (See DTC TABLE ) | 39, 40(1) 3J, 3M(2) |
|||||||||||||||||
| ETC_DSD (Electronic throttle control desired) | % | Indicate the desired TP by percent | Inspect following PIDs: APP1, APP2, ETC_ACT. Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION ) |
39, 40(1) 3J, 3M(2) |
|||||||||||||||||
| ° | Indicate the desired TP by angle | ||||||||||||||||||||
| EVAPCP (Purge solenoid valve duty value) | % | Ignition switch ON: 0% Idle: 0% | Inspect following PIDs: IAT, RPM, ECT, MAF, O2S11, BARO, INGEAR, VPWR. Inspect purge solenoid valve. (See PURGE SOLENOID VALVE INSPECTION ) |
85(1) 4U(2) |
|||||||||||||||||
| FAN1 (Cooling fan control) | On/Off | ECT below 100 °C {212 °F}: Off Others: On | Inspect following PIDs: RPM, TP, ECT, ACSW, COLP, TEST. Inspect cooling fan relay. (See RELAY INSPECTION ) |
69(1) 4L(2) |
|||||||||||||||||
| FAN2 (Cooling fan control) | On/Off | ECT below 108 °C {226 °F}: Off A/C operating, refrigerant pressure switch (middle) is OFF, and ECT below 108 °C {226 °F}: Off Others: On | Inspect following PIDs: RPM, TP, ECT, ACSW, COLP, TEST. Inspect cooling fan relay. (See ) |
93(1) 4F(2) |
|||||||||||||||||
| FAN3 (Cooling fan control) | On/Off | ECT below 100 °C {212 °F}: Off A/C operating, refrigerant pressure switch (middle) is ON, and ECT below 108 °C {226 °F}: Off Other: On | Inspect following PIDs: RPM, TP, ECT, ACSW, COLP, TEST. Inspect cooling fan relay. (See RELAY INSPECTION ) |
71 (1) 4B(2) |
|||||||||||||||||
| FLI (Fuel level) | % | Fuel gauge level F: Approx. 100% Fuel gauge level E: Approx. 0% |
Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| FP (Fuel pump relay) | On/Off | Idle: On Cranking: On |
Inspect following PIDs: RPM. Inspect fuel pump relay. (See RELAY INSPECTION ) | 95(1) 4Q(2) |
|||||||||||||||||
| FUELPW (Fuel injector duration) | ms | Ignition switch ON: 0 ms Idle (after warm up): Approx. 2.5 ms | Inspect following PIDs: IAT, MAF, TP, MAP, ECT, RPM, O2S11, O2S12, INGEAR, PSP, ACSW, VPWR, ALTT V. Inspect fuel injector. (See FUEL INJECTOR INSPECTION [L3] ) |
49, 50, 75, 76(1)/4W, 4Z, 4AA, 4AD(2) | |||||||||||||||||
| FUELSYS (Fuel system status) | OL/CL/OL Drive/OL Fault/CL Fault | Ignition switch ON: OL_Drive Idle (after warm up): CL | Inspect following PIDs: IAT, MAF, TP, MAP, ECT, RPM, O2S11, O2S12, INGEAR, PSP, ACSW, VPWR, ALTT V. Inspect fuel injector. (See FUEL INJECTOR INSPECTION [L3] ) |
- | |||||||||||||||||
| GENVDSD (Generator voltage desired) | V | Idle: Approx. 13.83 V(4) (E/L not operating) | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| HTR11 (HO2S heater (front)) | On/Off | Idle (after warm up): On --> Off | Inspect following PIDs: IAT, MAF, TP, ECT, RPM, ACSW. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 84(1) 4A(2) |
|||||||||||||||||
| HTR12 (HO2S heater (middle(1)/rear(2))) | On/Off | Idle: On Engine speed is above 4,000 rpm: Off |
Inspect following PIDs: IAT, MAF, ECT, RPM, ACSW. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 57(1) 4D(2) |
|||||||||||||||||
| HTR13(1) (HO2S heater (rear)) | On/Off | Idle: On Engine speed is above 4,000 rpm: Off |
Inspect following PIDs: IAT, MAF, ECT, RPM, ACSW. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 58 | |||||||||||||||||
| IASV (Variable air duct control solenoid valve) | On/Off | ECT is above 70 °C {158 °F}, engine speed is above 5,800 rpm, and TP opening angle is above 50%: On Others: Off | Inspect following PIDs: ECT, RPM, TP. Inspect VAD control solenoid valve. (See VARIABLE AIR DUCT (VAD) CONTROL SOLENOID VALVE INSPECTION ) |
68(1) 4C(2) |
|||||||||||||||||
| IAT (Intake air temperature) | °C | °F | Ignition switch at ON position: Indicate the IAT | Inspect IAT sensor. (See INTAKE AIR TEMPERATURE (IAT) SENSOR INSPECTION ) | 15(1) 2E(2) |
||||||||||||||||
| V | IAT 20 °C {68 °F}: Approx. 2.38V IAT 60 °C {140 °F}: Approx. 0.89V |
||||||||||||||||||||
| IMRC (Variable tumble solenoid valve) | On/Off | Engine speed is below Approx. 3,750 rpm and ECT is below 60 °C {140°F}: On Others: Off | Inspect following PIDs: TP, ECT, RPM. Inspect Variable tumble solenoid valve. (See VARIABLE TUMBLE SOLENOID VALVE INSPECTION ) |
74(1) 4T(2) |
|||||||||||||||||
| IMTV (Variable intake air solenoid valve) | On/Off | Engine speed is below Approx. 4,500 rpm: On Others: Off | Inspect following PIDs: RPM. Inspect Variable intake air solenoid valve. (See VARIABLE INTAKE AIR SOLENOID VALVE INSPECTION ) | 48(1) 4R(2) |
|||||||||||||||||
| INGEAR (Load/no load condition) | On/Off | CPP or CPP/PNP is On: Off Others: On | Perform applicable DTC troubleshooting. (See DTC TABLE ) | -(1) 1R, 1W(2) |
|||||||||||||||||
| IVS (CTP condition) | Idle/Off Idle | APP closed: Idle Others: Off Idle | Perform applicable DTC troubleshooting. (See DTC TABLE ) | 39, 40(1) 3J, 3M(2) |
|||||||||||||||||
| KNOCKR (Knocking retard) | ° | Ignition switch ON: 0 ° Idle: 0 ° | Inspect knock sensor. (See KNOCK SENSOR (KS) INSPECTION ) | 3, 81(1) 2P, 2S(2) |
|||||||||||||||||
| LDP_EVAPCP (EVAP system leak detection pump detect incorrect purge flow) | mA | Indicate the EVAP control system incorrect purge flow detection value | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LDP IDL (EVAP system leak detection pump idle current) | mA | Indicate the EVAP system leak detection pump idle current | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LDP_MON (EVAP system leak detection pump monitoring current) | mA | Indicate the EVAP system leak detection pump monitoring current | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LDP_REF (EVAP system leak detection pump reference current) | mA | Indicate the EVAP system leak detection pump reference current | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LDP_SLDV (EVAP system small leak detection value) | mA | Indicate the EVAP control system small leak detection value | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LDP_VSLDV(8) (EVAP system small leak detection value) | mA/sec | Indicate the EVAP control system vary small leak detection value | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| LOAD (Engine load) | % | Ignition switch ON: 0% Idle (after warm up): 15.9-17.1 %(3), 17.1-18.5%(7) Engine speed is 2,500 rpm: 13.3-14.3(3), 14.2-15.2(7) |
Inspect MAF sensor. (See MASS AIR FLOW (MAF) SENSOR INSPECTION ) | - | |||||||||||||||||
| LONGFT1 (long term fuel trim) | % | Idle (after warm up):-14-14% | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| MAF (Mass airflow) | g/s | Ignition switch ON: Approx. 0 g/s Idle (after warm up): 2.50-2.70 g/s(3), 2.72-2.94 g/s(7) Engine speed is 2,500 rpm: 7.56-8.18(3), 8.00-8.66(7) |
Inspect MAF sensor. (See MASS AIR FLOW (MAF) SENSOR INSPECTION ) | 11(1) 1P(2) |
|||||||||||||||||
| V | Ignition switch ON: Approx. 0.7 V Idle (after warm up): 1.15-1.28 V(3), 1.18-1.31 V(7) | ||||||||||||||||||||
| MAP (Manifold absolute pressure) | kPa, Bar, psi | Ignition switch at ON position: Indicate the atmospheric pressure | Inspect MAP sensor. (See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR INSPECTION ) | 14(1) 1J(2) |
|||||||||||||||||
| V | Ignition switch ON (at sea level): Approx. 4.1 V | ||||||||||||||||||||
| MIL (Malfunction indicator lamp) | On/Off | Ignition switch ON: On Idle: Off | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| MIL DIS (Traveled distance since the MIL illuminated) | km | mile | No DTC: 0 km {0 mile} DTC detected: Not 0 km {0 mile} | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | ||||||||||||||||
| NUMKEYS (Number of keys stored in module) | - | Indicate the number of keys stored in module | - | - | |||||||||||||||||
| O2S11 (Front oxygen sensor) | A(1) | Idle (after warm up): -1.0-1.0 A Deceleration (after warm up): 0.25 A or more | Inspect HO2S (front). (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 61 | |||||||||||||||||
| V(2) | Ignition switch ON: 0-1.0 V Idle (after warm up): 0-1.0 V Acceleration (after warm up): 0.5-1.0 V Deceleration (after warm up): 0-0.5 V |
1 AB | |||||||||||||||||||
| O2S12 (Middle(1)/rear(2) oxygen sensor) | V | Idle (after warm up): 0-1.0 V Acceleration (after warm up): 0.5-1.0 V Deceleration (after warm up): 0-0.5 V |
Inspect HO2S (rear). (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 44(1) 1Y(2) |
|||||||||||||||||
| O2S13(1) (Rear oxygen sensor) | V | Idle (after warm up): 0-1.0 V Acceleration (after warm up): 0.5-1.0 V Deceleration (after warm up): 0-0.5 V |
Inspect HO2S (rear). (See HEATED OXYGEN SENSOR (HO2S) INSPECTION ) | 45 | |||||||||||||||||
| PSP (Power steering pressure switch) | High/Low | Steering wheel in straight ahead position: Low Others: High | Inspect PSP switch. (See POWER STEERING PRESSURE (PSP) SWITCH INSPECTION ) | 55(1) 1Z(2) |
|||||||||||||||||
| RFCFLAG (Readness function code) | Learned/Not Learned | Before running PCM adaptive memory procedure drive mode: Not Learned After running PCM adaptive memory procedure drive mode: Learned |
Run PCM adaptive memory procedure drive mode. (See OBD-II DRIVE MODE ) | - | |||||||||||||||||
| RO2FT1 (Rear oxygen sensor fuel trim) | - |
|
|
44(1), Y(2) |
|||||||||||||||||
| RPM (Engine speed) | RPM | No load: 650-750 rpm E/L operating: 650-750 rpm P/S operating: 650-750 rpm A/C ON: 700-800 rpm |
Inspect CKP sensor. (See CRANKSHAFT POSITION (CKP) SENSOR INSPECTION ) | 1, 27(1) 2D, 2G(2) |
|||||||||||||||||
| SCCS(1) (Speed control command switch) | V | Press ON/OFF: Approx. 0 V Press CANCEL: Approx. .1.2 V Press SET/COAST: Approx. 3.2 V Press RES/ACCEL: Approx. 4.2 V Others: Approx. 5.0 V |
Inspect cruise control switch. (See CRUISE CONTROL SWITCH INSPECTION ) | 12 | |||||||||||||||||
| SEGRP (EGR valve (stepping motor) position) | No. of step | Idle: 0 step Cranking: 0-60 steps | Inspect following PIDs: MAF, TP, ECT, RPM, VSS. Inspect EGR valve. (See EGR VALVE INSPECTION [L3] ) |
- | |||||||||||||||||
| SEGRP DSD (Desired EGR valve (stepping motor) position) | % | Idle: 0% | Inspect following PIDs: MAF, TP, ECT, RPM, VSS. | - | |||||||||||||||||
| SELTESTDTC (DTC of KOEO/KOER self-test) | - | - | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| SHRTFT1 (Short term fuel trim [front HO2S]) | % | Idle (after warm up): Approx.-30-25% | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| SHRTFT 11(2) (Short term fuel trim [rear HO2S]) | % | Idle (after warm up): Approx.-30-25% | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| SHRTFT12 (Short term fuel trim) | % | Idle (after warm up): Approx.-30-25% | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| SHRTFT13(1) (Short term fuel trim) | % | Idle (after warm up): Approx.-30-25% | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | |||||||||||||||||
| SPARKADV (Ignition timing) | °(BTDC) | Idle: BTDC Approx. 8° | Inspect following PIDs: MAF, TP, ECT, RPM, INGEAR, PSP, ACSW, VPWR. Inspect ignition timing. (See ENGINE TUNE-UP ) | - | |||||||||||||||||
| Test (Test mode) | On/Off | - | - | - | |||||||||||||||||
| TIRESIZE (Tire revolution per mile) | rev/mile | Indicate the tire circumference length | - | - | |||||||||||||||||
| TP_REL (Relative TP) | % | APP closed: Approx. 7%(3), Approx. 14%(7) APP open: Approx. 99% |
Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION ) | 39, 40(1) 3J, 3M(2) |
|||||||||||||||||
| TP1 (TP sensor 1) | % | APP closed: 10.6-20.1% APP open: 85-95% |
Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION ) | 40(1) 3M(2) |
|||||||||||||||||
| V | APP closed: 0.53-1.00 V APP open: 4.25-4.75 V |
||||||||||||||||||||
| TP2 (TP sensor 2) | % | APP closed: 10.6-20.1% APP open: 85-95% |
Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION ) | 39(1) 3J(2) |
|||||||||||||||||
| V | APP closed: 4.00-4.47 V APP open: 0.25-0.75 V |
||||||||||||||||||||
| TPCT (Lowest closed throttle voltage) | V | Indicate the voltage of the closed TP sensor | Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION ) | 39, 40(1) 3J, 3M(2) |
|||||||||||||||||
| Vref(2) (Constant Voltage) | V | Ignition switch ON: Approx.5 V | Perform applicable DTC troubleshooting. (See DTC TABLE ) | 2K | |||||||||||||||||
| VSS (Vehicle speed) | km/h | MPH | Indicate the vehicle speed | Perform applicable DTC troubleshooting. (See DTC TABLE ) | - | ||||||||||||||||
| VT ACT1 (Actual valve timing) | ° | Idle: Approx. 0° | Inspect following PIDs: TP, ECT, RPM. Inspect OCV. (See OIL CONTROL VALVE (OCV) INSPECTION ) | 2, 28(1) 2J, 2M(2) |
|||||||||||||||||
| VT DIFF1 (Difference between actual valve timing and target valve timing) | ° | Idle: Approx. 0° | Inspect following PIDs: TP, ECT, RPM. Inspect OCV. (See OIL CONTROL VALVE (OCV) INSPECTION ) | 2, 28(1) 2J, 2M(2) |
|||||||||||||||||
| VT DUTY1 | % | Idle: Approx. 11.5% | Inspect following PIDs: TP, ECT, RPM. Inspect OCV. (See OIL CONTROL VALVE (OCV) INSPECTION ) | 2, 28(1) 2J, 2M(2) |
|||||||||||||||||
|
|||||||||||||||||||||