Function Inspection Using M-MDS

STEP	INSPECTION	RESULTS	ACTION
1	PURPOSE: VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
1		No	Go to the next step.
2	PURPOSE: RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION NOTE: Recording can be facilitated using the screen capture function of the PC. Record the FREEZE FRAME DATA/snapshot data on the repair order.	-	Go to the next step.
3	PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY OTHER RELATED DTCs OCCURRING Switch the ignition off, then ON (engine off). Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (Refer to ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .) Is the PENDING CODE/DTC P0335-00:, P0365-00:, P2090-00: or P2091-00: also present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (Refer to DTC P0335-00: [PCM (SKYACTIV-G 2.5T)] .) (Refer to DTC P0365-00: [PCM (SKYACTIV-G 2.5T)] .) (Refer to DTC P2090-00: [PCM (SKYACTIV-G 2.5T)] .) (Refer to DTC P2091-00: [PCM (SKYACTIV-G 2.5T)] .) Go to the next step.
3		No	Go to the next step.
4	PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC OCCURRING FROM OIL PRESSURE SWITCH Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (Refer to ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .) Is the PENDING CODE/DTC P0524-00: also present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (Refer to DTC P0524-00: [PCM (SKYACTIV-G 2.5T)] .) Go to the next step.
4		No	Go to the next step.
5	PURPOSE: VERIFY CONFORMITY OF ACTUAL EXHAUST VALVE TIMING AND DETERMINE IF MALFUNCTION IS CAUSED BY OCV OR CONNECTOR RELATED Start the engine and idle it. Access the following PIDs using the M-MDS: (Refer to ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .) VT_EX_ACT VT_EX_DES Perform the following: Race the engine at an engine speed of 3, 000 rpm or less . Run it at idle. Repeat Step 1 and 2 operations above five times in succession. Does the monitor value of the PID item VT_EX_ACT conform to the VT_EX_DES PID value?	Yes	Go to Step 7.
5		No	Go to the next step.
6	PURPOSE: VERIFY IF SPOOL VALVE IN OCV IS STUCK Switch the ignition off. Remove the OCV. (Refer to OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .) Inspect the OCV. (Refer to OIL CONTROL VALVE (OCV) INSPECTION [SKYACTIV-G 2.5T] .) Can the spool valve in OCV operation be verified?	Yes	Go to the troubleshooting procedure to perform the procedure from Step 4. If a malfunction occurs, perform diagnosis from Step 1 of the malfunction diagnostic procedure.
6		No	Replace the OCV. (Refer to OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .) Go to the troubleshooting procedure to perform the procedure from Step 8.
7	PURPOSE: VERIFY CONNECTOR CONNECTIONS Start the engine. Access the VT_EX_ACT PID using the M-MDS. (Refer to ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .) Does the PID value fluctuate when the following connectors are shaken? OCV PCM	Yes	Repair or replace the applicable wiring harness or connector parts. Go to the troubleshooting procedure to perform the procedure from Step 8.
7		No	Go to the troubleshooting procedure to perform the procedure from Step 4. If a malfunction occurs, perform diagnosis from Step 3 of the malfunction diagnostic procedure.