LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2017 >> CX-3 Sport, AWD >> Repair and Diagnosis >> Transmission >> Transmission Control Systems >> Automatic Transaxle Shift Mechanism >> Automatic Transaxle Shift Mechanism Removal/Installation >> Selector Cable Removal/Installation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Selector Cable Removal/Installation

  1. Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION .)
  2. Remove the selector lever knob. (See Selector Lever Removal/Installation .)
  3. Perform the following procedure to remove the selector cable (selector lever side).
    1. Remove the center console tray. (See CENTER CONSOLE TRAY REMOVAL/INSTALLATION .)
    2. Remove the shift bezel. (See SHIFT BEZEL REMOVAL/INSTALLATION .)
    3. Remove the upper panel. (See UPPER PANEL REMOVAL/INSTALLATION .)
    4. Remove the shift panel. (See SHIFT PANEL REMOVAL/INSTALLATION .)
    5. Remove the console side panel. (See CONSOLE SIDE PANEL REMOVAL/INSTALLATION .)
    6. Remove the front console box. (See FRONT CONSOLE BOX REMOVAL/INSTALLATION .)
    7. Remove the CD player. (See CD PLAYER REMOVAL .) (See CD PLAYER INSTALLATION .)
    8. Remove the front console. (See FRONT CONSOLE REMOVAL/INSTALLATION .)
    9. Remove the side wall. (See SIDE WALL REMOVAL/INSTALLATION .)
    10. Remove the rear console. (See REAR CONSOLE REMOVAL/INSTALLATION .)
    11. Pull out the safety lock in the direction of the arrow (1) shown in the figure, pull out the lock piece in the direction of the arrow (2) shown in the figure, and release the lock. (See Selector Cable (Selector Lever Side) Installation Note .)
      Fig 1: Pulling Out Safety Lock
      G11438223Courtesy of MAZDA MOTORS CORP.
    12. While pressing the cable outer end tab (selector lever side) in the direction of the arrow (3) shown in the figure, lift up cable outer end (selector lever side) in the direction of the arrow (4) shown in the figure to detach the cable outer end tab (selector lever side) from the bracket.
      Fig 2: Lifting Up Cable Outer End (Selector Lever Side)
      G09075592Courtesy of MAZDA MOTORS CORP.
    13. Remove the cable outer end (selector lever side) from the bracket.
    14. Remove the selector cable end (selector lever side) from the selector lever.
    Fig 3: Removing Selector Cable End (Selector Lever Side) From Selector Lever
    G09786243Courtesy of MAZDA MOTORS CORP.
  4. Perform the following procedure to remove the selector cable (transaxle side).
    1. Remove the air cleaner case. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-G 2.0] .)
    2. Remove the battery tray. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0] .)
    3. While pressing the bracket tab in the direction of the arrow shown in the figure, lift up the cable outer end (transaxle side) in the direction of the arrow shown in the figure to detach the bracket tab from the cable outer end (transaxle side).
      Fig 4: Lifting Up Cable Outer End (Transaxle Side)
      G09786244Courtesy of MAZDA MOTORS CORP.
    4. Remove the cable outer end (transaxle side) from the bracket. (See Cable Outer End (Transaxle Side) Installation Note .)
    5. Remove the clip from the selector cable end (transaxle side).
      Fig 5: Removing Cable Outer End (Transaxle Side) From Bracket
      G09075595Courtesy of MAZDA MOTORS CORP.
    6. Remove the selector cable end (transaxle side) from the manual shaft lever.
    Fig 6: Removing Selector Cable End (Transaxle Side) From Manual Shaft Lever
    G09075596Courtesy of MAZDA MOTORS CORP.
  5. Remove the clip as shown in the figure and remove the nut.
    Fig 7: Removing Clip
    G11438229Courtesy of MAZDA MOTORS CORP.
  6. Remove the grommet as shown in the figure and remove the nuts.
    Fig 8: Removing Grommet
    G11438230Courtesy of MAZDA MOTORS CORP.
  7. Install in the reverse order of removal.
scientia non olet · About LEMON Manuals