LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2018 >> 6 Signature >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> On-Board Diagnostic - Blind Spot Monitoring Control Module >> DTC Test (Blind Spot Monitoring (BSM) Control Module) >> Snapshot Data
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Snapshot Data

NOTE:
  • The blind spot monitoring (BSM) control module (LH) or (RH) stores the following two types of snapshot data (vehicle information) when a DTC is detected and displays them in the M-MDS.
    • Vehicle information detected by blind spot monitoring (BSM) control module (LH) or (RH)
    • Vehicle information detected by instrument cluster and received by blind spot monitoring (BSM) control module (LH) or (RH) via CAN communication
Snapshot Data Item Unit Data Contents Data Read/Use Method Corresponding Data Monitor Items
AAT °C °F Ambient temperature - -
APP_STATUS Accelerator Pedal Off/Under20%/Over20%/FAIL Accelerator pedal position status - -
CFG_STATUS Config Complete/Not Configured/Config Error Instrument cluster configuration status - -
ECT_STATUS Under 0 degrees C/0 - Under 80 degrees C/Over 80 degrees C/FAIL Engine coolant temperature status - -
IC_VPWR V Instrument cluster power supply voltage  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the power supply voltage value of the instrument cluster sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the power supply voltage of the instrument cluster when the DTC was detected, and it is displayed in the M-MDS.
 VPWR(1)
IG-ON_TIMER hh:mm:ss(2) Elapsed time since ignition was switched ON (engine off or on).
NOTE:
  • The instrument cluster records the elapsed time since the ignition was switched ON (engine off or on).
  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the elapsed time since the ignition was switched ON (engine off or on) sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the elapsed time since the ignition was switched ON (engine off or on) when the DTC was detected, and it is displayed in the M-MDS.
 -
PWR_MODE_KEY Key Out/Key Recently Out (Position 0)/Accessory (Position 1)/Post Ignition (Position 2)/Ignition On (Position 2)/Running (Position 2)/Running - Starting  
  • Key Out: Ignition switched off
  • Key Recently Out (Position 0): Elapsed time within 3 s since ignition was switched off
  • Accessory (Position 1): Ignition is switched to ACC
  • Post Ignition (Position 2): Elapsed time within 3 s since ignition was switched ON (engine off or on)
  • Ignition On (Position 2): Ignition switched ON (engine off)
  • Running (Position 2): Ignition switched ON (engine on)
  • Running - Starting: Cranking condition
  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the ignition switch status sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the ignition switch status when the DTC was detected, and it is displayed in the M-MDS.
 -
RPM_STATUS Engine Stop/Under1500rpm/Over1500rpm/FAIL Engine speed status  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the engine speed sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the engine speed when the DTC was detected, and it is displayed in the M-MDS.
 TACHOMTR(1)
SHIFT_STATUS P/N/D/FAIL Selector lever position status  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the selector lever position sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the selector lever position when the DTC was detected, and it is displayed in the M-MDS.
 -
TOTAL_DIST km Miles Accumulate d total traveled distance from completion of vehicle until blind spot monitoring (BSM) control module (LH) or (RH) detects DTC (Odometer value in instrument cluster) The total traveled distance from which the blind spot monitoring (BSM) control module (LH) or (RH) detects DTCs to the present can be calculated by performing the following procedure.
  1. Verify the odometer value in the instrument cluster.
  2. Verify the snapshot data item TOTAL_DIST.
  3. Subtract 2 from 1.
 -
TOTAL_TIME hh:mm:ss(2) Accumulate d total elapsed time since vehicle completion until blind spot monitoring (BSM) control module (LH) or (RH) detects a DTC
NOTE:
  • When the ROOM fuse is removed, and the ignition is switched off, the time is not included in the elapsed time.
 The elapsed time from which the blind spot monitoring (BSM) control module (LH) or (RH) detects DTCs to the present can be calculated by performing the following procedure.
  1. Verify the instrument cluster PID item TOTAL_TIME.
  2. Verify the snapshot data item TOTAL_TIME.
  3. Subtract 2 from 1.
 TOTAL_TIME
VPWR V Blind spot monitoring (BSM) control module (LH) or (RH) power supply voltage - VPWR_IG1
VSPD_STATUS Stop/0-10km/h/Over10km/h/FAIL Vehicle speed status  
  • The blind spot monitoring (BSM) control module (LH) or (RH) constantly receives the vehicle speed sent via CAN signal from the instrument cluster.
  • If a DTC is detected, the blind spot monitoring (BSM) control module (LH) or (RH) records the vehicle speed when the DTC was detected, and it is displayed in the M-MDS.
 SPEEDOMTR(1)
(1) Instrument cluster PID (See PID/DATA MONITOR TABLE [INSTRUMENT CLUSTER] .)
(2) The seconds may be indicated after the decimal point.
scientia non olet · About LEMON Manuals