Active Command Modes Table

WARNING: This page is about a different car, the 2016 Mazda CX-3. However, it is still accessible from the selected car via links, so may be relevant.

NOTE:

Simulation items on parts which are not equipped to the vehicle do not operate.

Simulation item	Unit/Operation	Data contents	Output part name	Operation condition
BG_HORN_RLY	If an accessory part is installed, it cannot be used.
BLWR_RLY	Off/On	Off: Turns the blower relay off. On: Turns the blower relay on.	Blower relay	Ignition switched ON (engine off or on)
DR_LK_RY	Off/On	NOTE: The BCM sends a door lock relay operation request signal (lock signal) to the ESU via LIN communication. Off: Does not lock the door. On: Locks the door.	Door lock relay	Ignition switched ON (engine off or on)
DR_UNLK_RY	Off/On	NOTE: The BCM sends a door unlock relay operation request signal (unlock signal) to the ESU via LIN communication. Off: Does not unlock the door. On: Unlocks the door.	Door unlock relay	Ignition switched ON (engine off or on)
F_FOG_RELAY	Off/On	Off: Turns the front fog light off. On: Turns the front fog light on.	Front fog light relay	Ignition switched ON (engine off or on)
H/L_CLN_RY	Displayed on M-MDS but does not function.
H/L_DRL	Off/On	NOTE: The BCM sends a running light on request signal to the ESU via LIN communication. Off: The running lights are turned off. On: The running lights are turned on.	Running light	Ignition switched ON (engine off or on)
H/L_HI	0%/100%	NOTE: The BCM sends a headlight HI on request signal to the ESU via LIN communication. 0%: The headlights HI are turned off. 100%: The headlights HI are turned on.	Headlight HI	Ignition switched ON (engine off or on)
H/L_LOW	0%/100%	NOTE: The BCM sends a headlight LO on request signal to the ESU via LIN communication. 0%: The headlights LO are turned off. 100%: The headlights LO are turned on.	Headlight LO	Ignition switched ON (engine off or on)
H/L_TNS	Off/Right-On/Left-On/On	NOTE: The BCM sends a TNS on request signal to the ESU via LIN communication. Off: Turns the parking lights off. Right-On: Turns the parking light (RH) on. Left-On: Turns the parking light (LH) on. On: Turns the parking lights (RH/LH) on.	Parking light	Ignition switched ON (engine off or on)
HORN_RLY	Off/On	Off: Stops the horn. On: Sounds the horn.	Horn relay	Ignition switched ON (engine off or on)
PTC_HEAT_ST	Displayed on M-MDS but does not function.
R_DEF_RLY	Off/On	Off: Stops the rear window defogger. On: Operates the rear window defogger.	Rear window defogger relay	Ignition switched ON (engine off or on)
R_FOG_LAMP	Off/On	Off: Turns the rear fog light off. On: Turns the rear fog light on.	Rear fog light relay	Ignition switched ON (engine off or on)
REVERSE_LMP	Off/On	NOTE: The BCM sends a back-up light on request signal to the ESU via LIN communication. Off: Turns the back-up light off. On: Turns the back-up light on.	Back-up light	Ignition switched ON (engine off or on)
ROOM_LAMP	Off/100%_On	NOTE: The BCM sends a front map light on request signal to the ESU via LIN communication. Off: Turns the front map light off. 100%_On: Turn the front map light on.	Front map light	Ignition switched ON (engine off or on)
STOP_LMP_CTL	Off/On	Off: Turns the brake light off. On: Turns the brake light on.	Brake light relay	Ignition switched ON (engine off or on)
TRUNK_LAMP	Off/On	NOTE: The BCM sends a cargo compartment light on request signal to the ESU via LIN communication. Off: Turns the cargo compartment light off. On: Turns the cargo compartment light on.	Cargo compartment light	Ignition switched ON (engine off or on)
TRUNK_MOTOR	Off/On	NOTE: The BCM sends a liftgate release signal to the ESU via LIN communication. Off: Does not open the liftgate. On: Opens the liftgate.	Liftgate release relay	Ignition switched ON (engine off or on)
WASHER_CTRL	Off/Front_ON	NOTE: The BCM sends a front washer operation request signal to the ESU via LIN communication. Off: Stops the windshield washer motor. Front_ON: Operates the windshield washer motor.	Windshield washer motor	Ignition switched ON (engine off or on)
WIP_R_CTRL	Off/INT/On/On_1Time/On_2Time/On_3Time/On_4Time	NOTE: The BCM sends a rear wiper operation request signal or rear wiper INT operation request signal to the ESU via LIN communication. Off: Stops the rear wiper. INT: Operates the rear wiper intermittently. On: Operates the rear wiper continuously. On_1Time: - On_2Time: Operates the rear wiper twice. On_3Time: - On_4Time: -	Rear wiper motor	Ignition switched ON (engine off or on)