| 1 |
VERIFY OTHER 360°VIEW MONITOR CONTROL MODULE DTCs
|
Yes |
Replace the 360°view monitor control module, then go to Step 8.
(See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION
.) |
| No |
Go to the next step. |
| 2 |
INSPECT 360°VIEW MONITOR CONTROL MODULE CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION
.)
- Disconnect the 360°view monitor control module connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 8. |
| 3 |
INSPECT FRONT CAMERA CONNECTOR CONDITION
- Disconnect the front camera connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 8. |
| 4 |
INSPECT FRONT CAMERA CIRCUIT FOR SHORT TO GROUND
- Verify that the front camera and 360°view monitor control module connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side) and body ground:
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- 360°view monitor control module terminal S-Front camera terminal D If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to ground.
Go to Step 8. |
| No |
Go to the next step. |
| 5 |
INSPECT FRONT CAMERA CIRCUIT FOR SHORT TO POWER SUPPLY
- Verify that the front camera and 360°view monitor control module connectors are disconnected.
- Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION
.)
- Switch the ignition ON (engine off or on).
- Measure the voltage at the following terminals (wiring harness-side):
- Is the voltage 0 V?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- 360°view monitor control module terminal S-Front camera terminal D If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has a short to power supply.
Go to Step 8. |
| 6 |
INSPECT FRONT CAMERA CIRCUIT FOR OPEN CIRCUIT
- Switch the ignition off.
- Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION
.)
- Verify that the front camera and 360°view monitor control module connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side):
- 360°view monitor control module terminal S-Front camera terminal D
- Is there continuity?
|
Yes |
Go to the next step. |
| No |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
- 360°view monitor control module terminal S-Front camera terminal D If there is a common connector:
- Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
- Repair or replace the malfunctioning part.
If there is no common connector:
- Repair or replace the wiring harness which has an open circuit.
Go to Step 8. |
| 7 |
INSPECT FRONT CAMERA
|
Yes |
Go to the next step. |
| No |
Replace the front camera, then go to the next step.
(See FRONT CAMERA REMOVAL/INSTALLATION
.) |
| 8 |
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
|
Yes |
Repeat the inspection from Step 1.
Go to the next step. |
| No |
Go to the next step. |
| 9 |
VERIFY IF OTHER DTCs DISPLAYED
- Are any other DTCs displayed?
|
Yes |
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [360°VIEW MONITOR CONTROL MODULE] .) |
| No |
DTC troubleshooting completed. |