LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2021 >> CX-5 Signature >> Repair and Diagnosis >> External Pages >> Different car >> Section 152 (On-Board Diagnostic - Adaptive Front Lighting System Control Module) >> DTC U3003:16 [Adaptive Front Lighting System (AFS) Control Module] >> Diagnostic Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnostic Procedure

WARNING: This page is about a different car, the 2017 Mazda CX-5. However, it is still accessible from the selected car via links, so may be relevant.
DTC U3003:16 (ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE) DIAGNOSTIC PROCEDURE

Step Inspection Action
1 VERIFY PCM DTCs Yes Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5)] .)
No Go to the next step.
2 INSPECT BATTERY Yes Go to the next step.
No Recharge or replace the battery, then go to Step 6.
(See BATTERY RECHARGING .) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
3 INSPECT GENERATOR Yes Go to the next step.
No Replace the generator, then go to Step 6.
(See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] .)
4 INSPECT ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE CONNECTOR CONDITION
  • Switch the ignition off.
  • Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION .)
  • Disconnect the adaptive front lighting system (AFS) control module connector.
  • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
  • Is the connector normal?
 Yes Go to the next step.
No Repair or replace the connector, then go to Step 6.
5 VERIFY ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE POWER SUPPLY VOLTAGE Yes Go to the next step.
No Inspect the METER1 10 A fuse.
  • If the fuse is blown:
    • Refer to the wiring diagram and verify whether or not there is a common connector between METER1 10 A fuse and adaptive front lighting system (AFS) control module terminal N.

      If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
    • Repair or replace the malfunctioning part.

      If there is no common connector:

  • Repair or replace the wiring harness which has a short to ground.
    • Replace the fuse.
    • If the fuse is damaged:
    • Replace the fuse.
  • If the fuse is normal:
    • Refer to the wiring diagram and verify whether or not there is a common connector between IG1 relay terminal C and adaptive front lighting system (AFS) control module terminal N.

      If there is a common connector:

  • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
    • Repair or replace the malfunctioning part.

      If there is no common connector:

    • Repair or replace the wiring harness which has an open circuit.

Go to the next step.
6 VERIFY THAT REPAIRS HAVE BEEN COMPLETED Yes Repeat the inspection from Step 1.
No Go to the next step.
7 VERIFY IF OTHER DTCs DISPLAYED
  • Are any other DTCs displayed?
 Yes Repair the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [ADAPTIVE FRONT LIGHTING SYSTEM (AFS) CONTROL MODULE] .)
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals