Common Specs & Procedures Index
CX-9 COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | HVAC TECHNICAL DATA | ||
| Torque | See Torque Specifications in text and appropriate graphics in BASIC SYSTEM - HVAC | ||
| Axle Nut/Hub Nut | |||
| Front | Step 1: Tighten to 100-150 N.m {11-15 kgf.m, 74-110 ft.lbf} Step 2: Loosen 180 degrees Step 3: Tighten to 260-300 N.m {27-30 kgf.m, 192-221 ft.lbf} |
||
| Rear | Step 1: Tighten to 100-150 N.m {11-15 kgf.m, 74-110 ft.lbf} Step 2: Loosen 180 degrees Step 3: Tighten to 236-274 N.m {25-27 kgf.m, 175-202 ft.lbf} |
||
| Battery | BATTERY INSPECTION | ||
| Brakes | |||
| Bleeding Sequence | BRAKE FLUID AIR BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | BRAKES TECHNICAL DATA | ||
| Torque | See Torque Specifications in text and appropriate graphics in CONVENTIONAL BRAKE SYSTEM | ||
| Charging | |||
| Generator | GENERATOR INSPECTION | ||
| Torque | See Torque Specifications in text and appropriate graphics in CHARGING SYSTEM | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT AUTO TENSIONER INSPECTION | ||
| Drive Belt Routing | NA | ||
| Engine Cooling | |||
| General Service Specifications | ENGINE TECHNICAL DATA | ||
| Radiator Cap Pressure | 13.6-17.7 psi | ||
| Thermostat R & I | THERMOSTAT REMOVAL/INSTALLATION | ||
| Water Pump R & I | WATER PUMP REMOVAL/INSTALLATION | ||
| Engine Mechanical | |||
| Compression | COMPRESSION INSPECTION | ||
| Oil Pressure | Lo: 135-165 kPa {1.38-1.68 kgf/cm2
, 19.6-23.9 psi} [1, 500 RPM] Hi: 225-275 kPa {2.30-2.80 kgf/cm2 , 32.7-39.8 psi} [4, 500 RPM] |
||
| Overhaul | ENGINE TECHNICAL DATA | ||
| Torque | See Torque Specifications in text and appropriate graphics in ENGINE MECHANICAL SYSTEM | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 108-116 N.m {11.1-11.8 kgf.m, 80-85 ft.lbf} | ||
| Fuel System | |||
| Pressure Specification | 79.1-100.0 psi (545-695 kPa, 5.56-7.08 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL LINE PRESSURE INSPECTION | ||
| Fuel Filter Location | Fuel filter is attached to fuel pump unit in fuel tank. | ||
| Fuel Filter R & I | FUEL FILTER (HIGH-PRESSURE) REMOVAL/INSTALLATION | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine has coil-on-plug ignition. | ||
| Spark Plug | |||
| PY8V-18-110 | |||
| Gap | Standard: 0.70-0.85mm {0.028-0.033 in} New spark plug (reference): 0.70-0.80mm {0.028- 0.031 in} |
||
| Torque | 15-20 N.m {1.6-2.0 kgf.m, 12-14 ft.lbf} | ||
| Starting | |||
| Starter | STARTER INSPECTION | ||
| Torque | See Torque Specifications in appropriate graphics under STARTER REMOVAL/INSTALLATION | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT | ||
| Torque | See Torque Specifications in text in FRONT SUSPENSION SYSTEM and REAR SUSPENSION SYSTEM | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80-108 Ft. Lbs. (108-147 N.m) | ||