Diagnostic Procedure

DTC U2301:56 (360° VIEW MONITOR CONTROL MODULE) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	INSPECT VEHICLE CONTROL MODULE (VCM) AND BODY CONTROL MODULE (BCM) FOR MALFUNCTION Switch the ignition OFF, and then switch it ON (engine off). Perform the DTC inspection for the vehicle control module (VCM) and the body control module (BCM). (See DTC INSPECTION .) Is a DTC related to a communication error or internal malfunction displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [VEHICLE CONTROL MODULE (US)] .) (See DTC TABLE [BODY CONTROL MODULE (BCM) (US)] .)
1		No	Go to the next step.
2	INSPECT 360°VIEW MONITOR CONTROL MODULE FOR MALFUNCTION Perform the DTC inspection for the 360°view monitor control module. (See DTC INSPECTION .) Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [360°VIEW MONITOR CONTROL MODULE (US)] .)
2		No	Go to the next step.
3	VERIFY 360°VIEW MONITOR CONTROL MODULE REPLACEMENT RECORD Verify if the 360°view monitor control module has been replaced before performing this troubleshooting procedure. Has the 360°view monitor control module been replaced?	Yes	After performing the procedure required for the 360°view monitor control module replacement again, perform the repair completion verification according to the [360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION]. (See 360° VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(US)] .)
3		No	Go to the next step.
4	VERIFY IF MALFUNCTION IS CAUSED BY BODY CONTROL MODULE (BCM) CONFIGURATION ERROR Switch the ignition OFF and wait for 30 s or more. Switch the ignition ON (engine off or on) and wait for 30 s or more. Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Go to the next step.
4		No	Go to repair completion verification 2.
5	VERIFY BODY CONTROL MODULE (BCM) CONFIGURATION RELATED DTCs Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting. (See DTC TABLE [BODY CONTROL MODULE (BCM) (US)] .)
5		No	Go to the next step.
6	RESET BODY CONTROL MODULE (BCM) CONFIGURATION DATA Using the M-MDS, perform the body control module (BCM) configuration. (See CONFIGURATION .) Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Replace the 360°view monitor control module and perform the repair completion verification. (See 360° VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(US)] .)
6		No	Go to repair completion verification 2.
Repair completion verification 1	VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform the DTC inspection for the vehicle control module (VCM). (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the body control module (BCM), then go to the next step. (See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION .)
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	VERIFY IF OTHER DTCs ARE DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Is a DTC displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.