| ACC_LAT |
G |
Displays the lateral acceleration speed (raw value).
- 0 G: Vehicle stopped or driving at constant speed
- Changes 0 G-positive: Cornering to left
- Changes 0 G-negative: Cornering to right
|
AN, AQ |
| ACC_LAT_C |
G |
Displays the lateral acceleration speed (calculated value).
- 0 G: Vehicle stopped or driving at constant speed
- Changes 0 G-positive: Cornering to left
- Changes 0 G-negative: Cornering to right
|
AN, AQ |
| ACC_LON |
G |
Displays the longitudinal acceleration speed (raw value).
- 0 G: Vehicle stopped or driving at constant speed
- Changes 0 G-positive: Vehicle is driving at a acceleration
- Changes 0 G-negative: Vehicle is driving at a deceleration
|
AN, AQ |
| ACC_LON_C |
G |
Displays the longitudinal acceleration speed (calculated value).
- 0 G: Vehicle stopped or driving at constant speed
- Changes 0 G-positive: Vehicle is driving at a acceleration
- Changes 0 G-negative: Vehicle is driving at a deceleration
|
AN, AQ |
| BRK_FLD_HYD_PRES |
mBar, Bar |
Displays the brake fluid pressure (calculated value) input from the brake fluid pressure sensor.
- Changes according to the brake fluid pressure: Brake pedal depressed
|
- |
| BRK_FLD_PRES |
mBar, Bar |
Displays the brake fluid pressure (raw value) input from the brake fluid pressure sensor.
- Changes according to the brake fluid pressure: Brake pedal depressed
|
- |
| BRK_FORCE_L |
kN |
Displays the estimated thrust of the left wheel brake. |
- |
| BRK_FORCE_R |
kN |
Displays the estimated thrust of the right wheel brake. |
- |
| BRK_PEDAL_SW |
Inactive/Active |
- Inactive: Brake pedal released
- Active: Brake pedal depressed
|
J, L |
| BRK_TEMP_L/R |
°C, °F |
Displays the estimated temperature of left rear wheel rear disc plate |
- |
| BRK_TEMP_R/R |
°C, °F |
Displays the estimated temperature of right rear wheel rear disc plate |
- |
| DSC_SW |
Inactive/Active |
- Inactive: DSC OFF switch is released
- Active: DSC OFF switch is depressed
|
J, L |
| DSC_SYS_STAT |
Passive/Active |
- Passive: DSC OFF mode
- Active: Other than DSC OFF mode (DSC control permitted condition)
|
- |
| DYC_DISABLE |
FALSE/TRUE |
- FALSE: G-vectoring control plus (yaw momentum control) control is permitted
- TRUE: G-vectoring control plus (yaw momentum control) control is inhibited
|
- |
| DYN_PARK_BRK |
Inactive/Active |
- Inactive: Emergency brake function is not operating
- Active: Emergency brake function is operating
|
- |
| EPB_ACTAT_APPLIED_L |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake operation is completed (electric parking brake motor gear unit (LH) is securing rear disc plate)
|
- |
| EPB_ACTAT_APPLIED_R |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake operation is completed (electric parking brake motor gear unit (RH) is securing rear disc plate)
|
- |
| EPB_ACTAT_APPLYING_L |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake is operating (electric parking brake motor gear unit (LH) is securing rear disc plate)
|
- |
| EPB_ACTAT_APPLYING_R |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake is operating (electric parking brake motor gear unit (RH) is securing rear disc plate)
|
- |
| EPB_ACTAT_RELEASED_L |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake release is completed (electric parking brake motor gear unit (LH) releases rear disc plate)
|
- |
| EPB_ACTAT_RELEASED_R |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake release is completed (electric parking brake motor gear unit (RH) releases rear disc plate)
|
- |
| EPB_ACTAT_RELEASING_L |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake is releasing (electric parking brake motor gear unit (LH) is releasing rear disc plate)
|
- |
| EPB_ACTAT_RELEASING_R |
Inactive/Active |
- Inactive: Conditions other than below
- Active: Electric parking brake is releasing (electric parking brake motor gear unit (RH) is releasing rear disc plate)
|
- |
| EPB_ACTAT_STAT |
Inactive/Active |
- Inactive: Electric parking brake motor gear unit is not operating
- Active: Electric parking brake motor gear unit is operating
|
- |
| EPB_APPLYING |
Inactive/Active |
- Inactive: Electric parking brake is not operating
- Active: Electric parking brake is operating
|
- |
| EPB_AUTO_ADJ |
Inactive/Active |
- Inactive: Except below
- Active: Electric parking brake is operating to adjust rear disc pad clearance
|
- |
| EPB_DYN_BRK |
Inactive/Active |
- Inactive: While electric parking brake is operating, vehicle is not being driven or clamp does not operate again when brake temperature is high
- Active: While electric parking brake is operating, vehicle is not being driven or clamp is operating again when brake temperature is high
|
- |
| EPB_MAINT_MODE_L |
Inactive/Active |
- Inactive: Not in maintenance mode
- Active: Transitions to maintenance mode, and clearance between disc pads of electric parking brake motor gear unit (LH) and rear disc plates is widened
|
- |
| EPB_MAINT_MODE_R |
Inactive/Active |
- Inactive: Not in maintenance mode
- Active: Transitions to maintenance mode, and clearance between disc pads of electric parking brake motor gear unit (RH) and rear disc plates is widened
|
- |
| EPB_RELEASING |
Inactive/Active |
- Inactive: Electric parking brake is not released
- Active: Electric parking brake is released
|
- |
| EPB_STAT_1 |
Inactive/Active |
- Inactive: Electric parking brake motor gear unit (LH) position cannot be detected
- Active: Electric parking brake motor gear unit (LH) position can be detected
|
- |
| EPB_STAT_2 |
Inactive/Active |
- Inactive: Electric parking brake motor gear unit (RH) position cannot be detected
- Active: Electric parking brake motor gear unit (RH) position can be detected
|
- |
| EPB_STATIC_APPLIED |
Inactive/Active |
- Inactive: Electric parking brake operation is not completed while vehicle is stopped
- Active: Electric parking brake operation is completed while vehicle is stopped
|
- |
| EPB_STATIC_RELEASED |
Inactive/Active |
- Inactive: Electric parking brake operation release is not completed while vehicle is stopped
- Active: Electric parking brake operation release is completed while vehicle is stopped
|
- |
| EPB_SW |
Neutral/Apply/Release/Error |
- Neutral: Electric parking brake switch is in neutral position
- Apply: Electric parking brake switch is pulled up
- Release: Electric parking brake switch is pushed down
- Error: Electric parking brake switch position is unknown
|
- |
| FALL_BACK_PARK_BRK |
Inactive/Active |
NOTE:
- Displays in the M-MDS but it does not operate.
|
- |
| HDC_SW |
Inactive/Active |
NOTE:
- Displays in the M-MDS but it does not operate.
|
- |
| HYD_PUMP_STAT |
Not Activated/Activated |
Displays the implementation condition of the hydraulic pressure control by the pump.
- Not Activated: Pump motor not activated
- Activated: Pump motor activated
|
A, AS |
| PAD_MAINT_MODE |
Inactive/Active |
- Inactive: Not in maintenance mode
- Active: In maintenance mode
|
- |
| PARK_BRK_COUNT |
|
Displays the number of electric parking brake operations. |
- |
| PARK_BRK_CUR_L/R |
A |
1-20 A: Electric parking brake motor gear unit (LH) is operating |
- |
| PARK_BRK_CUR_R/R |
A |
1-20 A: Electric parking brake motor gear unit (RH) is operating |
- |
| PARK_BRK_SW |
Inactive/Active |
NOTE:
- Displays in the M-MDS but it does not operate.
|
- |
| RBT_MODE |
Inactive/Active |
NOTE:
- Displays in the M-MDS but it does not operate.
|
- |
| REGEN_BRK |
No/Yes |
NOTE:
- Displays in the M-MDS but it does not operate.
|
- |
| REV_GEAR_SW |
Off/On |
ATX
- Off: Selector lever is in position other than R position
- On: Selector lever is in R position MTX
- Off: Shift lever is in position other than reverse
- On: Shift lever is in reverse
|
J, L |
| ROLLER_MODE |
Inactive/Active |
- Inactive: Not in electric parking brake inspection mode
- Active: In electric parking brake inspection mode
|
- |
| STR_ANG |
◦ |
NOTE:
- Constantly indicates 0° until the steering wheel angle neutral position determination by the DSC HU/Control Module is completed.
- The steering wheel angle neutral position determination by the DSC HU/Control Module is completed when the vehicle is driven in a straight line at a speed of 20 km/h {12 mph} or more for several seconds.
Displays the steering angle (calculated value).
- 0°: Steering wheel in neutral position
- Changes 0°-positive: Steering wheel turned to left
- Changes 0°-negative: Steering wheel turned to right
|
J, L |
| STR_ANG_R |
◦ |
NOTE:
- The signal displayed in this item is a steering angle (relative angle) signal output from the EPS control module.
Displays the steering angle (raw value).
- 0°: Steering wheel in neutral position
- Changes 0°-positive: Steering wheel turned to left
- Changes 0°-negative: Steering wheel turned to right
|
J, L |
| TCS_DUMP_L/F |
Off/On |
- Off: Outlet solenoid valve (LF) is stopped
- On: Outlet solenoid valve (LF) is operating
|
- |
| TCS_DUMP_L/R |
Off/On |
- Off: Outlet solenoid valve (LR) is stopped
- On: Outlet solenoid valve (LR) is operating
|
- |
| TCS_DUMP_R/F |
Off/On |
- Off: Outlet solenoid valve (RF) is stopped
- On: Outlet solenoid valve (RF) is operating
|
- |
| TCS_DUMP_R/R |
Off/On |
- Off: Outlet solenoid valve (RR) is stopped
- On: Outlet solenoid valve (RR) is operating
|
- |
| TCS_ISOLAT_VLV_1 |
Off/On |
- Off: Traction control solenoid valve (LF/RR) is stopped
- On: Traction control solenoid valve (LF/RR) is operating
|
- |
| TCS_ISOLAT_VLV_2 |
Off/On |
- Off: Traction control solenoid valve (RF/LR) is stopped
- On: Traction control solenoid valve (RF/LR) is operating
|
- |
| TCS_ISOLAT_VLV_L/F |
Off/On |
- Off: Inlet solenoid valve (LF) is stopped
- On: Inlet solenoid valve (LF) is operating
|
- |
| TCS_ISOLAT_VLV_L/R |
Off/On |
- Off: Inlet solenoid valve (LR) is stopped
- On: Inlet solenoid valve (LR) is operating
|
- |
| TCS_ISOLAT_VLV_R/F |
Off/On |
- Off: Inlet solenoid valve (RF) is stopped
- On: Inlet solenoid valve (RF) is operating
|
- |
| TCS_ISOLAT_VLV_R/R |
Off/On |
- Off: Inlet solenoid valve (RR) is stopped
- On: Inlet solenoid valve (RR) is operating
|
- |
| TCS_PUMP_MOTOR |
Off/On |
Displays the pump motor operation condition.
- Off: Pump motor not activated
- On: Pump motor activated
|
A, AS |
| TCS_SUPPLY_1 |
Off/On |
- Off: Stability control solenoid valve (LF/RR) is stopped
- On: Stability control solenoid valve (LF/RR) is operating
|
- |
| TCS_SUPPLY_2 |
Off/On |
- Off: Stability control solenoid valve (RF/LR) is stopped
- On: Stability control solenoid valve (RF/LR) is operating
|
- |
| TCS_VLV_SUPPLY |
Off/On |
- Off: Power supply to inlet solenoid valves and outlet solenoid valves of each wheel is stopped
- On: Power supply to inlet solenoid valves and outlet solenoid valves of each wheel is implemented
|
A, AT |
| VPWR |
V |
Displays the power supply voltage to the DSC HU/Control Module. |
A, AT |
| VSS |
KPH, MPH |
Displays the vehicle speed. |
M, P, S, V, Y AB, AE, AH |
| WSPD_SEN_L/F |
KPH, MPH |
Displays the wheel speed of the left front wheel received from the ABS wheel-speed sensor (LF). |
S, V |
| WSPD_SEN_L/R |
KPH, MPH |
Displays the wheel speed of the left rear wheel received from the ABS wheel-speed sensor (LR). |
Y, AB |
| WSPD_SEN_R/F |
KPH, MPH |
Displays the wheel speed of the right front wheel received from the ABS wheel-speed sensor (RF). |
AE, AH |
| WSPD_SEN_R/R |
KPH, MPH |
Displays the wheel speed of the right rear wheel received from the ABS wheel-speed sensor (RR). |
M, P |
| YAW_RATE |
°/s |
Displays the yaw rate (raw value) received from the yaw rate sensor.
- 0°/s: Vehicle stopped or driving straight
- Changes 0°/s-positive: Cornering to left
- Changes 0°/s-negative: Cornering to right
|
AN, AQ |
| YAW_RATE_C |
°/s |
Displays the yaw rate (calculated value) received from the yaw rate sensor.
- 0°/s: Vehicle stopped or driving straight
- Changes 0°/s-positive: Cornering to left
- Changes 0°/s-negative: Cornering to right
|
AN, AQ |