| 1 |
INSPECT POWER LIFTGATE (PLG) TOUCH SENSOR (LH) CONNECTOR CONDITION
- Switch the ignition off.
- Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION
.)
- Disconnect the power liftgate (PLG) touch sensor (LH) connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 7. |
| 2 |
INSPECT POWER LIFTGATE (PLG) TOUCH SENSOR (RH) CONNECTOR CONDITION
- Disconnect the power liftgate (PLG) touch sensor (RH) connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 7. |
| 3 |
INSPECT POWER LIFTGATE (PLG) CONTROL MODULE CONNECTOR CONDITION
- Disconnect the power liftgate (PLG) control module connector.
- Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.
- Is the connector normal?
|
Yes |
Go to the next step. |
| No |
Repair or replace the connector, then go to Step 7. |
| 4 |
INSPECT TOUCH SENSOR CIRCUIT FOR SHORT TO GROUND
- Verify that the power liftgate (PLG) touch sensor (LH), power liftgate (PLG) touch sensor (RH) and power liftgate (PLG) control module connectors are disconnected.
- Inspect for continuity between the following terminals (wiring harness-side) and body ground:
- Power liftgate (PLG) touch sensor (LH) terminal D
- Power liftgate (PLG) touch sensor (RH) terminal D
- Is there continuity?
|
Yes |
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
|
| |
Go to the next step. |
| 5 |
INSPECT POWER LIFTGATE (PLG) TOUCH SENSOR (LH)
- Measure the voltage at the following terminals (wiring harness-side):
- Power liftgate (PLG) control module terminal 1N
- Power liftgate (PLG) control module terminal 1M
- Is the voltage normal? (See POWER LIFTGATE (PLG) CONTROL MODULE INSPECTION
.)
|
Yes |
Go to the next step. |
| No |
Replace the power liftgate (PLG) touch sensor (LH), then go to Step 7.
(See POWER LIFTGATE (PLG) TOUCH SENSOR REMOVAL/INSTALLATION
.) |
| 6 |
INSPECT POWER LIFTGATE (PLG) TOUCH SENSOR (RH)
- Measure the voltage at the following terminals (wiring harness-side):
- Power liftgate (PLG) control module terminal 1P
- Power liftgate (PLG) control module terminal 1M
- Is the voltage normal? (See POWER LIFTGATE (PLG) CONTROL MODULE INSPECTION
.)
|
Yes |
Go to the next step. |
| No |
Replace the power liftgate (PLG) touch sensor (RH), then go to the next step.
(See POWER LIFTGATE (PLG) TOUCH SENSOR REMOVAL/INSTALLATION
.) |
| 7 |
VERIFY THAT REPAIRS HAVE BEEN COMPLETED
- Always reconnect all disconnected connectors.
- Connect the negative battery terminal. (See NEGATIVE BATTERY
TERMINAL
DISCONNECTION/CONNECTION.)
- Clear the DTC for the power liftgate (PLG) control module using the M-MDS. (See CLEARING DTC [POWER LIFTGATE (PLG) CONTROL MODULE] .)
- Switch the ignition off and wait for 5 min or more.
- Retrieve the power liftgate (PLG) control module
DTCs using the M-MDS. (See DTC INSPECTION
[POWER LIFTGATE (PLG) CONTROL MODULE].)
- Is the same DTC displayed?
|
Yes |
Repeat the inspection from Step 1.
|
| No |
Go to the next step. |
| 8 |
VERIFY IF OTHER DTCs DISPLAYED
- Are any other DTCs displayed?
|
Yes |
Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.
(See DTC TABLE [POWER LIFTGATE (PLG) CONTROL MODULE] .) |
| No |
DTC troubleshooting completed. |