LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2023 >> CX-50 S >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Exterior Lights >> On-Board Diagnostic - Light Control Module >> PID/Data Monitor Table [Light Control Module]
April 5, 2026: LEMON Manuals is launched! Read the announcement.

PID/Data Monitor Table [Light Control Module]

-: Not applicable

PID/DATA MONITOR DESCRIPTION (LIGHT CONTROL MODULE)

PID Unit/Operation Data contents Module control terminal
B1_CAL_VOLT - Displays correction value based on calibration of terminal +B1 input voltage -
B1_VOLT V Displays voltage at light control module terminal +B1 -
B2_CAL_VOLT - Displays correction value based on calibration of terminal +B2 input voltage -
B2_VOLT V Displays voltage at light control module terminal +B2 -
CAL_COUNT count Displays number of times calibration is performed -
CAL_CUR_INCLINATION_1 - Displays tilt correction value based on calibration of terminal String-1 (LOW GND, +LOW, DRL GND/+LOW and +DRL2) output voltage -
CAL_CUR_INCLINATION_2 - Displays tilt correction value based on calibration of terminal String-2 (+HIGH and FAN SIG) output voltage -
CAL_CUR_INTERCEPT_1 mA Displays correction value of section based on calibration of terminal String-1 (LOW GND, +LOW, DRL GND/+LOW and +DRL2) output voltage -
CAL_CUR_INTERCEPT_2 mA Displays correction value of section based on calibration of terminal String-2 (+HIGH and FAN SIG) output voltage -
FAN_VOLT V Displays voltage at terminal +FAN  
HSS_SW_1_1 Not equipped/Equipped
  • Not equipped: HSS switch1 is not equipped.
  • Equipped: HSS switch1 is not equipped.
 -
HSS_SW_1_2 Not equipped/Equipped
  • Not equipped: HSS switch2 is not equipped.
  • Equipped: HSS switch2 is not equipped.
 -
HSS_SW_2_1  
NOTE:
  • Displays in the M-MDS but it does not operate.
HSS1_CUR_1 mA Displays current of HSS switch1 -
HSS1_CUR_2 mA Displays current of HSS switch2 -
HSS1_CUR_3  
NOTE:
  • Displays in the M-MDS but it does not operate.
HSS1_STAT_1 Off/On
  • OFF: HSS switch1 is off.
  • ON: HSS switch1 is on.
 -
HSS1_STAT_2 Off/On
  • OFF: HSS switch2 is off.
  • ON: HSS switch2 is on.
 -
HSS2_STAT_1  
NOTE:
  • Displays in the M-MDS but it does not operate.
IG1_CAL_VOLT - Displays correction value based on calibration of IG1 power supply terminal input voltage -
IG1_STAT Off/On
  • OFF: IG1 power supply is not input to light control module.
  • ON: IG1 power supply is input to light control module.
 -
IG1_VOLT V Displays voltage at light control module IG1 power supply terminal -
INSPECTION_DATA Not complete/Complete
  • Not complete: Lighting appliance shipment inspection is not completed.
  • Complete: Lighting appliance shipment inspection is completed.
 -
LCM_POS Right/Left
  • Right: Light control module is installed on right.
  • Left: Light control module is installed on left.
 -
LED1_CAL_VOLT_1 - Displays tilt correction value based on calibration of terminals +LOW, DRL GND/+LOW and +DRL2 output voltage -
LED1_CAL_VOLT_2 - Displays tilt correction value based on calibration of terminals LOW GND, +LOW and DRL GND/+LOW output voltage -
LED1_CUR1_DRL mA Displays set current of terminals +LOW, DRL GND/+LOW and +dRl2 when running light is turned on -
LED1_CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR1_HI mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 when headlight HI is turned on -
LED1_CUR1_LO mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 when headlight LO is turned on -
LED1_CUR1_OUTLET1 mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 -
LED1_CUR1_OUTLET2 mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 -
LED1_CUR1_POS mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 when TNS (parking lights) is turned on -
LED1_CUR1_TURN mA Displays set current of terminals +LOW, DRL GND/+LOW and +DRL2 when front turn lights is turned on -
LED1_CUR2_DRL mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW when running light is turned on -
LED1_CUR2_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_CUR2_HI mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW when headlight HI is turned on -
LED1_CUR2_LO mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW when headlight LO is turned on -
LED1_CUR2_OUTLET1 mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW -
LED1_CUR2_OUTLET2 mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW -
LED1_CUR2_POS mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW when TNS (parking lights) is turned on -
LED1_CUR2_TURN mA Displays set current of terminals LOW GND, +LOW and DRL GND/+LOW when front turn lights is turned on -
LED1_DUTY_1 % Displays duty value of terminals +LOW, DRL GND/+LOW and +DRL2 -
LED1_DUTY_2 % Displays duty value of terminals LOW GND, +LOW and DRL GND/+LOW -
LED1_TGT_CUR1_DRL mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current when running light is turned on -
LED1_TGT_CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR1_HI mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current when headlight HI is turned on -
LED1_TGT_CUR1_LO mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current when headlight LO is turned on -
LED1_TGT_CUR1_OUTLET1 mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current -
LED1_TGT_CUR1_OUTLET2 mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current -
LED1_TGT_CUR1_POS mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current when TNS (parking lights) is turned on -
LED1_TGT_CUR1_TURN mA Displays target value of terminals +LOW, DRL GND/+LOW and +DRL2 output current when front turn lights is turned on -
LED1_TGT_CUR2_DRL mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current when running light is turned on -
LED1_TGT_CUR2_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED1_TGT_CUR2_HI mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current when headlight HI is turned on -
LED1_TGT_CUR2_LO mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current when headlight LO is turned on -
LED1_TGT_CUR2_OUTLET1 mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current -
LED1_TGT_CUR2_OUTLET2 mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current -
LED1_TGT_CUR2_POS mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current when TNS (parking lights) is turned on -
LED1_TGT_CUR2_TURN mA Displays target value of terminals LOW GND, +LOW and DRL GND/+LOW output current when front turn lights is turned on -
LED1_VOLT_1 V Displays voltage at terminals +LOW, DRL GND/+LOW and +DRL2 -
LED1_VOLT_2 V Displays voltage at terminals LOW GND, +LOW and DRL GND/+LOW -
LED2_CAL_VOLT_1 - Displays tilt correction value based on calibration of terminals +HIGH and FAN SIG output voltage -
LED2_CUR1_DRL mA Displays set current of terminals +HIGH and FAN SIG when running light is turned on -
LED2_CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_CUR1_HI mA Displays set current of terminals +HIGH and FAN SIG when headlight HI is turned on -
LED2_CUR1_LO mA Displays set current of terminals +HIGH and FAN SIG when headlight LO is turned on -
LED2_CUR1_OUTLET1 mA Displays set current of terminals +HIGH and FAN SIG -
LED2_CUR1_OUTLET2 mA Displays set current of terminals +HIGH and FAN SIG -
LED2_CUR1_POS mA Displays set current of terminals +HIGH and FAN SIG when TNS (parking lights) is turned on -
LED2_CUR1_TURN mA Displays set current of terminals +HIGH and FAN SIG when front turn lights is turned on -
LED2_TGT_CUR1_DRL mA Displays target value of terminals +HIGH and FAN SIG output current when running light is turned on -
LED2_TGT CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED2_TGT_CUR1_HI mA Displays target value of terminals +HIGH and FAN SIG output current when headlight HI is turned on -
LED2_TGT CUR1_LO mA Displays target value of terminals +HIGH and FAN SIG output current when headlight LO is turned on -
LED2_TGT_CUR1POS mA Displays target value of terminals +HIGH and FAN SIG output current when TNS (parking lights) is turned on -
LED2_TGT_CUR1_TURN mA Displays target value of terminals +HIGH and FAN SIG output current when front turn lights is turned on -
LED2_TGT_CUR2OUTLET1 mA Displays target value of terminals +HIGH and FAN SIG output current -
LED2_TGT_CUR2_OUTLET2 mA Displays target value of terminals +HIGH and FAN SIG output current -
LED2_VOLT_1 V Displays voltage at terminals +HIGH and FAN SIG -
LED3_CAL_VOLT_1 - Displays tilt correction value based on calibration of terminals DRL GND output voltage -
LED3_CUR1_DRL mA Displays set current of terminals DRL GND when running light is turned on -
LED3_CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3_CUR1_HI mA Displays set current of terminals DRL GND when headlight HI is turned on -
LED3_CUR1_LO mA Displays set current of terminals DRL GND when headlight LO is turned on -
LED3_CUR1_OUTLET1 mA Displays set current of terminals DRL GND -
LED3_CUR1_OUTLET2 mA Displays set current of terminals DRL GND -
LED3_CUR1_POS mA Displays set current of terminals DRL GND when TNS (parking lights) is turned on -
LED3_CUR1_TURN mA Displays set current of terminals DRL GND when front turn lights is turned on -
LED3_DUTY_1 % Displays duty value of terminals DRL GND -
LED3_TGT_CUR1_DRL mA Displays target value of terminals DRL GND output current when running light is turned on -
LED3_TGT_CUR1_FSM  
NOTE:
  • Displays in the M-MDS but it does not operate.
LED3_TGT_CUR1_HI mA Displays target value of terminals DRL GND output current when headlight HI is turned on -
LED3_TGT_CUR1_LO mA Displays target value of terminals DRL GND output current when headlight LO is turned on -
LED3_TGT_CUR1_POS mA Displays target value of terminals DRL GND output current when TNS (parking lights) is turned on -
LED3_TGT_CUR1_TURN mA Displays target value of terminals DRL GND output current when front turn lights is turned on -
LED3_TGT_CUR2_OUTLET1 mA Displays target value of terminals DRL GND output current -
LED3_TGT_CUR2_OUTLET2 mA Displays target value of terminals DRL GND output current -
LED3_VOLT_1 V Displays voltage at terminal DRL GND -
LVL_ACTAT_VOLT V Displays voltage at terminal LVL SIG -
LVL_VOLT_RATIO % Displays voltage ratio of terminal LVL SIG -
STRING_CUR_1 mA Displays base current of terminals LOW GND, +LOW, DRL GND/+LOW and +DRL2 -
STRING_CUR_2 mA Displays base current of terminals +HIGH and FAN SIG -
STRING_CUR_3 mA Displays base current of terminal DRL GND -
THERMISTOR_VOLT_1 V Displays voltage of terminal HIGH GND -
THERMISTOR_VOLT_2 V Displays voltage of terminal THERM -
THERMISTOR_VOLT_INSIDE V Displays voltage of internal thermistor -
scientia non olet · About LEMON Manuals