Body Control System
- Body Control Module (BCM) Bracket Removal/Installation [L.H.D.]
- D-code
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver Side Front Scuff Plate
- Remove Front Side Trim (Left Side)
- Remove Passenger Side Decoration Panel
- Remove Driver Side Decoration Panel
- Remove Driver Side Lower Panel
- Remove Driver-side Knee Air Bag Module
- Remove Body Control Module (BCM)
- Remove Body Control Module (BCM) Bracket
- Install in Reverse Order of Removal
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Body Control Module (BCM) Inspection
- Body Control Module (BCM) Removal/Installation [L.H.D.]
- D-code
- Verify/Program Personalization Features
- Verify/Program Vehicle Status Monitor
- Prepare Body Control Module (BCM)/Electrical Supply Unit (ESU)/Door-Electrical Supply Unit/Power Liftgate (PLG) Control Module For Synchronization
- Start Configuration (If Parts Are Replaced)
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver Side Front Scuff Plate
- Remove Front Side Trim (Left Side)
- Remove Passenger Side Decoration Panel
- Remove Driver Side Decoration Panel
- Remove Driver Side Lower Panel
- Remove Driver-side Knee Air Bag Module
- Remove Body Control Module (BCM)
- Install in Reverse Order of Removal
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Complete Configuration (If Parts Are Replaced)
- Perform Immobilizer System-Related Part Programming
- Perform Position Memory System Memory Clearing
- Perform Seat Position Initial Setting (With Position Memory System)
- Perform Vehicle Control Module (VCM) Initial Setting
- Cancel Connected Services Disable Mode/Connected Vehicle Maintenance Mode
- Complete Body Control Module (BCM)/Electrical Supply Unit (ESU)/Door-Electrical Supply Unit/Power Liftgate (PLG) Control Module Synchronization
- Inspect for DTCs
- Clear DTCs
- Control System Location Index [L.H.D.]
- Door-Electrical Supply Unit Inspection
- Driver-Side Door-Electrical Supply Unit Removal/Installation [L.H.D.]
- D-code
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver Side Inner Garnish
- Remove Power Window Main Switch
- Remove Driver Side Front Door Speaker Grille
- Remove Driver Side Front Door Trim
- Remove Driver Side Door-Electrical Supply Unit
- Install in Reverse Order of Removal
- Perform Configuration (If Parts Are Replaced)
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Electrical Supply Unit (ESU) Inspection
- Electrical Supply Unit (ESU) Removal/Installation [L.H.D.]
- D-code
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Trunk Covering
- Remove Trunk Board (Rear)
- Remove Trunk End Trim
- Remove Third-row Seat Cushion
- Remove Third-row Seat Back Component
- Remove Trunk side upper trim (LH)
- Partially Peel Back Trunk Side Trim (LH)
- Remove Electrical Supply Unit (ESU)
- Install in Reverse Order of Removal
- Perform Configuration (If Parts Are Replaced)
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Passenger-Side Door-Electrical Supply Unit Removal/Installation [L.H.D.]
- D-code
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Passenger Side Inner Garnish
- Remove Power Window Subswitch (Front)
- Remove Passenger Side Front Door Speaker Grille
- Remove Passenger Side Front Door Trim
- Remove Passenger Side Door-Electrical Supply Unit
- Install in Reverse Order of Removal
- Perform Configuration (If Parts Are Replaced)
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Vehicle Control Module (VCM) Initial Setting
- Vehicle Control Module (VCM) Inspection
- Vehicle Control Module (VCM) Removal/Installation
- D-code
- Verify/Program Personalization Features
- Verify/Program Vehicle Status Monitor
- Prepare Body Control Module (BCM)/Electrical Supply Unit (ESU)/Door-Electrical Supply Unit/Power Liftgate (PLG) Control Module For Synchronization
- Start Configuration (If Parts Are Replaced)
- Remove Cover Assembly (Passenger's Side)
- Disconnect Negative Lead-Acid Battery Terminal
- Remove Driver Side Front Scuff Plate
- Remove Front Side Trim (Left Side)
- Remove Passenger Side Decoration Panel
- Remove Driver Side Decoration Panel
- Remove Driver Side Lower Panel
- Remove Driver-side Knee Air Bag Module
- Remove Body Control Module (BCM)
- Install in Reverse Order of Removal
- Perform Power Liftgate Initialization
- Initialize Power Outer Mirror Retract/Return Function
- Complete Configuration (If Parts Are Replaced)
- Perform Immobilizer System-Related Part Programming
- Perform Position Memory System Memory Clearing
- Perform Seat Position Initial Setting (With Position Memory System)
- Perform Vehicle Control Module (VCM) Initial Setting
- Cancel Connected Services Disable Mode/Connected Vehicle Maintenance Mode
- Complete Body Control Module (BCM)/Electrical Supply Unit (ESU)/Door-Electrical Supply Unit/Power Liftgate (PLG) Control Module Synchronization
- Inspect for DTCs
- Clear DTCs