Troubleshooting Diagnostic Procedure

WARNING: <<High voltage>>

If necessary measures such as wearing the correct protective gear are not taken when inspecting or removing/installing the high voltage parts, it could cause electrical shock and result in serious injury or, in the worst case, death.
Before inspecting or removing/installing the high voltage parts, refer to [HIGH VOLTAGE SERVICE CAUTIONS ] in the general information and [High Voltage Part Inspection and Removal/Installation Notes] of the high voltage system service cautions and implement the necessary measures and preparations. (Refer to [HIGH VOLTAGE SERVICE CAUTIONS ] in service information). (Refer to [HIGH VOLTAGE SYSTEM SERVICE CAUTIONS ] in service information).

P0D5C-00: (OBC) DIAGNOSTIC PROCEDURE

Step	Inspection	Results	Action
1	PURPOSE: PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS BATTERY CHARGE CONTROL MODULE Switch the main power OFF. Disconnect the negative lead-acid battery terminal and wait for 1 min or more. (Refer to [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION ] in service information). Connect the negative lead-acid battery terminal. (Refer to [NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION ] in service information). Clear the DTC recorded in the memory. (See CLEARING DTC .) Perform charging using charging equipment other than that used when the DTC was output. Perform the DTC inspection for the battery charge control module. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Go to the next step.
1		No	Go to repair completion verification 2.
2	PURPOSE: VERIFY OTHER BATTERY CHARGE CONTROL MODULE DTCs Perform the DTC inspection for the battery charge control module. (See DTC INSPECTION .) Are any of the following DTCs displayed? P0D27: 00 P0D28: 00 P0D2A: 00 P0D4E: 00 P0D4F: 00 P0D54: 00	Yes	Repair or replace the malfunctioning location according to the applicable DTC troubleshooting. (See P0D27-00: [OBC] ). (See P0D28-00: [OBC] ). (See P0D2A-00: [OBC] ). (See P0D4E-00: [OBC] ). (See P0D4F-00: [OBC] ). (See P0D54-00: [OBC] ).
2		No	Go to the next step.
3	PURPOSE: INSPECT BATTERY CHARGE CONTROL MODULE FOR MALFUNCTION DEPENDING ON REPEATABILITY Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Implement the repeatability verification procedure. (See Repeatability Verification Procedure ). Perform the DTC inspection for the battery charge control module. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See MALFUNCTION DIAGNOSIS FLOW [CONTROLLER AREA NETWORK (CAN)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the battery charge control module, then go to the repair completion verification 2. (Refer to [ONBOARD CHARGER REMOVAL/INSTALLATION ] in service information).
3		No	Go to repair completion verification 2.
Repair completion verification 1	PURPOSE: VERIFY THAT VEHICLE IS REPAIRED Install/connect the part removed/disconnected during the troubleshooting procedure. Clear the DTC recorded in the memory. (See CLEARING DTC .) Replicate the vehicle conditions at the time the DTC was detected using the following procedure. Implement the repeatability verification procedure. (See Repeatability Verification Procedure ). Perform the DTC inspection for the battery charge control module. (See DTC INSPECTION .) Is the same Pending DTC present?	Yes	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See MALFUNCTION DIAGNOSIS FLOW [CONTROLLER AREA NETWORK (CAN)] .) If the CAN communication is normal, perform the diagnosis from Step 1. If the malfunction recurs, replace the battery charge control module, then go to the next step. (Refer to [ONBOARD CHARGER REMOVAL/INSTALLATION ] in service information).
Repair completion verification 1		No	Go to the next step.
Repair completion verification 2	PURPOSE: VERIFY IF OTHER DTCs DISPLAYED Perform the DTC inspection. (See DTC INSPECTION .) Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning location according to the applicable DTC troubleshooting.
Repair completion verification 2		No	DTC troubleshooting completed.