ME knock control, function - GF07.61-P-4031MOS
ENGINE 275.953 in MODEL 216.376, 221.176 as of Model Year 09 /AEJ 08
ENGINE 275.982 in MODEL 216.379, 221.179 as of Model Year 09 /AEJ 08
Function requirements for knock control, general points
- Circuit 87M ON (engine control ON)
- Engine running
Knock control, general points
The knock control is integrated in the ME-SFI control unit (N3/10) and its purpose is to ensure knock-free engine operation in all operating conditions and when different fuel grades are used. If there is uncontrolled combustion (knocking), the ignition angle of the ECI ignition module for the related cylinder (on RH or LH cylinder bank (N92/1, N92/2)) is adjusted towards "retard".
The ME-SFI control unit (N3/10) manages the knock control according to the following sensors and signals:
- Front and rear knock sensor (left engine side) (A29/1, A29/2)
- Front and rear knock sensor (right engine side) (A30/1, A30/2)
- Camshaft Hall sensor, RH cylinder bank (B6/3), ignition circuit detection
- Charge air temperature sensor (B17/8) and pressure sensor downstream of throttle valve actuator (B28/7), engine load
- Coolant temperature sensor (B11/4)
- Accelerator pedal sensor (B37), load request by driver
- Crankshaft position sensor (L5), engine speed and crankshaft position (ignition circuit detection)
- RON presetting (Research Octane Number) with the Diagnosis Assistance System (DAS) (except code (494) USA version)
The requirements of the engine torque-requirement function are also taken into account.
Knock control function sequence
The function sequence is described in the following steps:
- Ignition angle adjustment function sequence
- RON correction function sequence
- Knock control adaptation function sequence
- Knock identification error function sequence
Ignition angle adjustment function sequence
Knock control is enabled in the following operating conditions:
- Coolant temperature > 70 °C
- Engine load > 40 %
According to its input signals, the ME-SFI control unit calculates the cylinder-specific ignition angle correction.
If knocking is detected in a cylinder by the knock sensors, the ignition angle for this cylinder is adjusted towards "retard" (depending on engine speed) by about 3° CKA (CranK Angle) at the next ignition. If knocking still occurs, the ignition angle is adjusted towards "retard" by about another 3° CKA, and so on until the maximum adjustment is reached (about 10 to 15° CKA).
If there is no knocking, after a few ignitions the retard adjustment is reversed in steps of about 0.75° crank angle, until the normal performance map value is reached, or until knocking occurs again.
RON correction function sequence
The RON correction can be preset with the DAS through the correction programming (except code (494) USA version).
Knock control is also fitted out with an automatic RON switch. This detects a persistent high knocking tendency of the engine and assists the knock control by means of an appropriate pre-control. This is done by evaluating the stored adaptation values, the ignition angle of all the cylinders and the number of control interventions in certain engine load and speed ranges.
Depending on the threshold which has been exceeded, the RON stage is adjusted by one or several stages. The regulated RON stage remains until stopping of the engine.
The higher the RON stage selected, the lower the maximum retardation of the ignition angle.
Knock control adaptation function sequence
The adaptation of the knock control is active from a coolant temperature of approx. 75°C.
The ignition angle corrections required due to combustion knocking are stored continuously for the specific cylinder, along with the related operating condition of the engine (engine load and engine speed).
When determining the individual ignition angles, the stored adaptation values are taken into account, so that the optimal ignition angle can be calculated immediately for each cylinder. During abrupt acceleration, no values are stored for about 2 seconds in order to avoid any incorrect adaptation values.
Knock identification error function sequence
For safety reasons, if one of the knocking sensor signals fails, the ignition angles of all cylinders is retarded by up to 11° crank angle (according to engine speed and coolant temperature). Knock control and the adaptation are deactivated and a fault is stored in the fault memory.
The ignition angle corrections are added by the overheating/knock protection and knock control according to the performance map.
| Electrical function schematic for knock control | Model 216 | PE07.61-P-2786-97CAA | |
| Model 221 | PE07.61-P-2786-97SAA | ||
| ME-SFI [ME] control unit, component description | N3/10 | GF07.61-P-6000MOS |