LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mercedes Benz >> 2011 >> E63 >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Electrical System - Engine - 212 Chassis - 1 Of 2 >> Basic Knowledge >> Preheat, function >> Preheat, function - GF15.20-P-3005OGA
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Preheat, function - GF15.20-P-3005OGA

ENGINE 642.8 in MODEL 207 as of 6/1/13, 212, 218 as of model year 2014 

Function requirements for preheating, general points 

Preheating, general points 

The preglow system warms up the engine combustion chambers to the ignition temperature required for ignition of the fuel/air mixture.

IMPORTANT At cold temperatures the vent line heater element (R39/1) is actuated by the CDI control unit (N3/9). This prevents the crankcase ventilation system from freezing and therefore associated engine damage.

Function sequence for preheating 

The function sequence is subdivided into the following steps:

Function sequence for preheating 

The CDI control unit receives the message "circuit 15 ON" from the electronic ignition lock control unit (N73) via chassis CAN 1 (CAN E1). The CDI control unit reads in the engine oil temperature via the oil temperature sensor (B1) and then actuates the glow output stage (N14/3) via the drivetrain LIN (LIN C1) depending on the coolant temperature. The glow output stage then actuates the glow plugs (R9) on the positive side. At the same time, the CDI control unit sends a request to actuate the preglow indicator lamp (A1e16) via the CAN bus to the instrument cluster (A1).

IMPORTANT The messages for actuation of the preglow indicator lamp are received by the instrument cluster via chassis CAN 2 (CAN E2) and are routed by the front SAM control unit with fuse and relay module which receives the message from the CDI control unit on chassis CAN 1.

IMPORTANT If an error occurs in the preglow system, at the glow plugs or in the lines, this is shown by the preglow indicator lamp and is stored in the CDI control unit.

Function sequence for start-ready glowing 

Start-ready glowing ensures an adequately high temperature until the engine finally begins to run. If the CDI control unit receives the information "circuit 50 ON" from the electronic ignition lock control unit via chassis CAN 1, it will continue to actuate the glow output stage for a certain time irrespective of the engine oil temperature, and the glow output stage in turn actuates the glow plugs. After the start-ready temperature of 1250°C has been reached, the preglow indicator lamp goes out.

Function sequence for start-up glowing 

Start-up glowing is used to stabilize the cold start speed of the engine. If the CDI control unit receives the "circuit 61 ON" message from the alternator (G2) via the drive LIN, the glow output stage is actuated over the drive LIN. The glow output stage then actuates the glow plugs. In this way the first working cycles and the eventual running of the engine are supported.

Function sequence for afterglowing 

Afterglowing improves engine running after a cold start and the engine warm-up characteristics.

After a successful engine start, the CDI control unit reads in the engine oil temperature via the oil temperature sensor and actuates the glow plugs via the glow output stage depending on the engine oil temperature.

Function sequence for diagnostic glowing 

This function is used to energize the glow plugs to a low temperature level and a system diagnosis is performed. This function is activated for troubleshooting purposes and when the preglow system has not been activated for a long period (no preheating required owing to high ambient temperature).

Function sequence for DPF glow function, with code (474) Particulate filter 

The DPF glow function is used to raise the load and to stabilize combustion and thus to assist regeneration of the DPF. To do this the CDI control unit receives the message "circuit 50 ON" via chassis CAN 1 from the electronic ignition lock control unit. The CDI control unit then requests the glow output stage.

Function sequence for emergency glowing 

If a problem in communication occurs between the CDI control unit and the glow output stage so that the glow output stage does not recognize any activity for 2 s after activation via circuit 87, the emergency glowing function is actuated for 180 s. If communication is missing during a glowing process for more than 250 ms then the glowing process will be continued for 180 s.

IMPORTANT If no new glow request is received from the CDI control unit then emergency glowing stops after 180 s.

  Electrical function schematic for preheating, model 207   PE15.20-P-2051-97EAJ
  Electrical function schematic for preheating, model 212   PE15.20-P-2051-97DAM
  Electrical function schematic for preheating, model 218   PE15.20-P-2051-97XAE
  Overview of system components for common rail diesel injection (CDI)   GF07.16-P-9997OG
scientia non olet · About LEMON Manuals