Engine Control DTCS
ENGINE CONTROLS DTCS (ME17.7 ENGINE 272)
| MB DTC | Generic DTC | Description |
| B10E800 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B10E900 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B10EC00 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B10EC19 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B110909 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B110A00 | - | Fault code in A9/5 (Electric refrigerant compressor) control unit |
| B1CAF00 | - | The crash sensor transmits signals continuously. |
| EB1BC700 | - | There is an internal fault in control unit 'Supplemental Restraint System'. |
| EC000100 | - | This fault can be ignored and erased. |
| EC000200 | - | This fault can be ignored and erased. |
| EC000300 | - | This fault can be ignored and erased. |
| EC000400 | - | This fault can be ignored and erased. |
| EC001000 | - | This fault can be ignored and erased. |
| EC001100 | - | This fault can be ignored and erased. |
| EC001200 | - | This fault can be ignored and erased. |
| EC001400 | - | This fault can be ignored and erased. |
| EC001500 | - | This fault can be ignored and erased. |
| EC001600 | - | This fault can be ignored and erased. |
| EC001800 | - | This fault can be ignored and erased. |
| EC001900 | - | This fault can be ignored and erased. |
| EC001A00 | - | This fault can be ignored and erased. |
| EC001C00 | - | This fault can be ignored and erased. |
| EC001D00 | - | This fault can be ignored and erased. |
| EC001E00 | - | This fault can be ignored and erased. |
| EC002000 | - | This fault can be ignored and erased. |
| EC002100 | - | This fault can be ignored and erased. |
| EC002200 | - | This fault can be ignored and erased. |
| EC003000 | - | This fault can be ignored and erased. |
| EC003100 | - | This fault can be ignored and erased. |
| EC003200 | - | This fault can be ignored and erased. |
| EC003300 | - | This fault can be ignored and erased. |
| EC003400 | - | This fault can be ignored and erased. |
| EC003500 | - | This fault can be ignored and erased. |
| EC003600 | - | This fault can be ignored and erased. |
| EC003700 | - | This fault can be ignored and erased. |
| EC003800 | - | This fault can be ignored and erased. |
| EC003900 | - | This fault can be ignored and erased. |
| EC003A00 | - | This fault can be ignored and erased. |
| EC003B00 | - | This fault can be ignored and erased. |
| EC004200 | - | This fault can be ignored and erased. |
| EC004600 | - | This fault can be ignored and erased. |
| EC004800 | - | This fault can be ignored and erased. |
| EC006A00 | - | This fault can be ignored and erased. |
| EC109000 | - | This fault can be ignored and erased. |
| EC120200 | - | This fault can be ignored and erased. |
| EC120300 | - | This fault can be ignored and erased. |
| EC123300 | - | This fault can be ignored and erased. |
| EC123600 | - | This fault can be ignored and erased. |
| EC125000 | - | This fault can be ignored and erased. |
| EC125200 | - | This fault can be ignored and erased. |
| EC125400 | - | This fault can be ignored and erased. |
| EC126000 | - | This fault can be ignored and erased. |
| EC127000 | - | This fault can be ignored and erased. |
| EC128100 | - | This fault can be ignored and erased. |
| EC128200 | - | This fault can be ignored and erased. |
| EC182500 | - | This fault can be ignored and erased. |
| EC186500 | - | This fault can be ignored and erased. |
| EC190800 | - | This fault can be ignored and erased. |
| EC191000 | - | This fault can be ignored and erased. |
| EC193300 | - | This fault can be ignored and erased. |
| EC193400 | - | This fault can be ignored and erased. |
| EC196500 | - | This fault can be ignored and erased. |
| EC196700 | - | This fault can be ignored and erased. |
| EC197500 | - | This fault can be ignored and erased. |
| EC197600 | - | This fault can be ignored and erased. |
| EC200100 | - | This fault can be ignored and erased. |
| EC200200 | - | This fault can be ignored and erased. |
| EC212B00 | - | This fault can be ignored and erased. |
| EP046000 | - | The left fuel level sensor has a malfunction. |
| EP046002 | - | The left fuel level sensor has a malfunction. There is a general signal fault. |
| EP046200 | - | The left fuel level sensor has a short circuit to ground. |
| EP046300 | - | The left fuel level sensor has a short circuit to positive. |
| EP050008 | - | Speed sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| EP050009 | - | Speed sensor 1 has a malfunction. |
| EP057529 | - | Input 'CRUISE CONTROL' has an electrical fault. There is an invalid signal. |
| EP070229 | - | CAN signal 'Torque request' from control unit Transmission is implausible. |
| EP164404 | - | An incorrect variant coding or configuration was detected. There is an internal fault. |
| EP164408 | - | An incorrect variant coding or configuration was detected. There is a signal fault or the message is faulty. |
| EP164429 | - | An incorrect variant coding or configuration was detected. There is an invalid signal. |
| EP164464 | - | An incorrect variant coding or configuration was detected. There is an implausible signal. |
| EP206500 | - | The right fuel level sensor has a malfunction. |
| EP206502 | - | The right fuel level sensor has a malfunction. There is a general signal fault. |
| EP206700 | - | The right fuel level sensor has a short circuit to ground. |
| EP206800 | - | The right fuel level sensor has a short circuit to positive. |
| EP261000 | - | The engine off time has an implausible value. |
| EP261008 | - | The engine off time has an implausible value. There is a signal fault or the message is faulty. |
| EP261029 | - | The engine off time has an implausible value. There is an invalid signal. |
| EP261084 | - | The engine off time has an implausible value. There is a signal below the permissible limit value. |
| EP261085 | - | The engine off time has an implausible value. There is a signal above the permissible limit value. |
| EU000900 | - | Drive train CAN bus OFF fault |
| EU002886 | - | CAN bus OFF : Short circuit Powertrain-Bus |
| EU002888 | - | Communication with control unit 'Regenerative braking system' has a malfunction. |
| EU003788 | - | The vehicle speed signal was not received. |
| EU010100 | - | Communication with control unit 'Transmission' has a malfunction. |
| EU010187 | - | No CAN message was received from control unit Transmission. (U0101) |
| EU010300 | - | Communication with the electronic selector lever module has a malfunction. |
| EU010900 | - | Communication with control unit 'Fuel pump' has a malfunction. |
| EU012000 | - | Communication with the starter or alternator has a malfunction. |
| EU012100 | - | Communication with ESP has a malfunction. |
| EU012181 | - | Communication with ESP has a malfunction. Incorrect data were received. |
| EU012800 | - | Communication with the electric parking brake has a malfunction. |
| EU013200 | - | Communication with control unit 'Suspension' has a malfunction. |
| EU014600 | - | Communication with the central gateway has a malfunction. |
| EU015500 | - | Communication with the instrument cluster has a malfunction. |
| EU015587 | - | Communication with the instrument cluster has a malfunction. The message is missing. |
| EU016400 | - | Communication with the air conditioning has a malfunction. |
| EU016800 | - | Communication with the electronic ignition lock has a malfunction. |
| EU021200 | - | Communication with the steering column module has a malfunction. |
| EU025900 | - | No CAN message was received from control unit PSM Parameterizable Special Module. |
| EU029300 | - | Communication with control unit 'Hybrid system' has a malfunction. |
| EU040200 | - | Implausible data were received from control unit 'Transmission'. |
| EU040281 | - | Implausible data were received from control unit 'Transmission'. Incorrect data were received. |
| EU040400 | - | Implausible data were received from the electronic selector lever module. |
| EU040500 | - | Implausible data were received from the speed control system. |
| EU041200 | - | Implausible data were received from control unit 'Battery'. |
| EU041500 | - | Implausible data were received from ESP. |
| EU041581 | - | Implausible data were received from ESP. Incorrect data were received. |
| EU041586 | - | Implausible data were received from ESP. There is an incorrect signal. |
| EU041700 | - | Implausible data were received from the electric parking brake. |
| EU042100 | - | One or more signals sent from control unit N51/2 (ABC control module) via the CAN bus is implausible. |
| EU042700 | - | Implausible data were received from the electronic ignition lock. |
| EU042900 | - | Implausible data were received from the steering column module. |
| EU044700 | - | Implausible data were received from the central gateway. |
| EU113E00 | - | Communication with the battery sensor has a malfunction. |
| EU140781 | - | The engine torque is implausible. |
| EU140786 | - | The engine torque is implausible. |
| EU140787 | - | The engine torque is implausible. |
| EU140800 | - | An implausible signal from switch 'Brake lights' was received. |
| EU140808 | - | An implausible signal from switch 'Brake lights' was received. There is a signal fault or the message is faulty. |
| EU140D86 | - | An implausible wheel speed signal was received. There is an incorrect signal. |
| P001000 | - | Actuator 'Intake camshaft' (cylinder bank 1) has an electrical fault or open circuit. |
| P001164 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P001177 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. |
| P001200 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. |
| P001300 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has an electrical fault or open circuit. |
| P001464 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P001477 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. |
| P001500 | - | Adjustment of the exhaust camshaft (cylinder bank 1) is performed late. |
| P001600 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. |
| P001664 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. |
| P001700 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. |
| P001764 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. |
| P001800 | - | The position of the intake camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. |
| P001864 | - | The position of the intake camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. |
| P001900 | - | The position of the exhaust camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. |
| P001964 | - | The position of the exhaust camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. |
| P002000 | - | Actuator 'Intake camshaft' (cylinder bank 2) has an electrical fault or open circuit. |
| P002164 | - | The position of the intake camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P002177 | - | The position of the intake camshaft (cylinder bank 2) deviates from the specified value. The commanded position cannot be reached. |
| P002200 | - | Adjustment of the intake camshaft (cylinder bank 2) is performed late. |
| P002300 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has an electrical fault or open circuit. |
| P002464 | - | The position of the exhaust camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P002477 | - | The position of the exhaust camshaft (cylinder bank 2) deviates from the specified value. The commanded position cannot be reached. |
| P002500 | - | Adjustment of the exhaust camshaft (cylinder bank 2) is performed late. |
| P003000 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P003100 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P003200 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P003600 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P003700 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P003800 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P004000 | - | Oxygen sensors 1 (cylinder banks 1 and 2) have been swapped. |
| P004100 | - | Oxygen sensors 2 (cylinder banks 1 and 2) have been swapped. |
| P005000 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P005100 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has a short circuit to ground. |
| P005200 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has a short circuit to positive. |
| P005400 | - | The heater for oxygen sensor 2 (cylinder bank 1) has an implausible electrical resistance value. |
| P005600 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has an electrical fault or open circuit. |
| P005700 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has a short circuit to ground. |
| P005800 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has a short circuit to positive. |
| P006000 | - | The heater for oxygen sensor 2 (cylinder bank 2) has an implausible electrical resistance value. |
| P006800 | - | The position of the throttle valve is implausible relative to the mass air flow or intake manifold pressure. |
| P007126 | - | The position of the throttle valve is implausible relative to the mass air flow or intake manifold pressure. |
| P007127 | - | The outside temperature sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P007200 | - | The outside temperature sensor has a short circuit to ground. |
| P007300 | - | The outside temperature sensor has a short circuit to positive. |
| P008900 | - | Pressure regulating valve 1 has a malfunction. |
| P008B00 | - | The pressure in the fuel low pressure circuit is too high. |
| P009E07 | - | This error code can be ignored and erased. |
| P010100 | - | Mass air flow sensor 1 has a malfunction. |
| P010126 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is below the permissible limit value. |
| P010127 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P010184 | - | Mass air flow sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P010185 | - | Mass air flow sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P010186 | - | Mass air flow sensor 1 has a malfunction. There is an incorrect signal. |
| P010200 | - | Mass air flow sensor 1 has a short circuit to ground. |
| P010211 | - | Mass air flow sensor 1 has a short circuit to ground. There is a short circuit to ground. |
| P010300 | - | Mass air flow sensor 1 has a short circuit to positive. |
| P010426 | - | Hot film mass air flow sensor 1 has a sporadic malfunction. The signal change rate is below the permissible limit value. |
| P010427 | - | Hot film mass air flow sensor 1 has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P010617 | - | The intake manifold pressure sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P010684 | - | The intake manifold pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P010685 | - | The intake manifold pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P01068F | - | The intake manifold pressure sensor has a malfunction. The signal or message is erratic. |
| P010700 | - | The intake manifold pressure sensor has a short circuit to ground. |
| P010800 | - | The intake manifold pressure sensor has a short circuit to positive. |
| P011127 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. The signal change rate is above the permissible limit value. |
| P011128 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P011216 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to ground. The limit value for electrical voltage has not been attained. |
| P011317 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to positive. The limit value for electrical voltage has been exceeded. |
| P011604 | - | Coolant temperature sensor 1 has a malfunction. There is an internal fault. |
| P01161C | - | Coolant temperature sensor 1 has a malfunction. The voltage value is outside the permissible range. |
| P011684 | - | Coolant temperature sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P011685 | - | Coolant temperature sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P011686 | - | Coolant temperature sensor 1 has a malfunction. There is an incorrect signal. |
| P011700 | - | Coolant temperature sensor 1 has a short circuit to ground. |
| P01171C | - | Coolant temperature sensor 1 has a short circuit to ground. The voltage value is outside the permissible range. |
| P011800 | - | Coolant temperature sensor 1 has a short circuit to positive. |
| P011B84 | - | Coolant temperature implausible in comparison to the intake air temperature. There is a signal below the permissible limit value. |
| P011B85 | - | Coolant temperature implausible in comparison to the intake air temperature. There is a signal above the permissible limit value. |
| P012200 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P012300 | - | Position sensor 1 for the throttle valve has a short circuit to positive. |
| P012800 | - | The coolant temperature is below the coolant thermostat specified temperature. |
| P013011 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a short circuit to ground. |
| P013012 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a short circuit to positive. |
| P013084 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a signal below the permissible limit value. |
| P013300 | - | Oxygen sensor 1 (cylinder bank 1) has a delayed reaction. |
| P013504 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is an internal fault. |
| P013584 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a signal below the permissible limit value. |
| P013600 | - | Oxygen sensor 2 (cylinder bank 1) has an electrical fault. |
| P013700 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P013800 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P013A00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is too slow. |
| P013C00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 2) is too slow. |
| P013E00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is delayed. |
| P014A00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 2) is delayed. |
| P015011 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a short circuit to ground. |
| P015012 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a short circuit to positive. |
| P015084 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a signal below the permissible limit value. |
| P015300 | - | Oxygen sensor 1 (cylinder bank 2) has a delayed reaction. |
| P015504 | - | The heater for oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is an internal fault. |
| P015584 | - | The heater for oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a signal below the permissible limit value. |
| P015600 | - | Oxygen sensor 2 (cylinder bank 2) has an electrical fault. |
| P015700 | - | Oxygen sensor 2 (cylinder bank 2) has a short circuit to ground. |
| P015800 | - | Oxygen sensor 2 (cylinder bank 2) has a short circuit to positive. |
| P017000 | - | The mixture formation (cylinder bank 1) has a malfunction. |
| P017004 | - | The mixture formation (cylinder bank 1) has a malfunction. There is an internal fault. |
| P017100 | - | The mixture (cylinder bank 1) is too lean. |
| P017184 | - | The mixture (cylinder bank 1) is too lean. There is a signal below the permissible limit value. |
| P017185 | - | The mixture (cylinder bank 1) is too lean. There is a signal above the permissible limit value. |
| P017204 | - | The mixture (cylinder bank 1) is too rich. There is an internal fault. |
| P017284 | - | The mixture (cylinder bank 1) is too rich. There is a signal below the permissible limit value. |
| P017285 | - | The mixture (cylinder bank 1) is too rich. There is a signal above the permissible limit value. |
| P017300 | - | The mixture formation (cylinder bank 2) has a malfunction. |
| P017304 | - | The mixture formation (cylinder bank 2) has a malfunction. There is an internal fault. |
| P017400 | - | The mixture (cylinder bank 2) is too lean. |
| P017484 | - | The mixture (cylinder bank 2) is too lean. There is a signal below the permissible limit value. |
| P017485 | - | The mixture (cylinder bank 2) is too lean. There is a signal above the permissible limit value. |
| P017500 | - | The mixture (cylinder bank 2) is too rich. |
| P017584 | - | The mixture (cylinder bank 2) is too rich. There is a signal below the permissible limit value. |
| P017585 | - | The mixture (cylinder bank 2) is too rich. There is a signal above the permissible limit value. |
| P020100 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. |
| P020200 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. |
| P020300 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. |
| P020400 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. |
| P020500 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. |
| P020600 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. |
| P021700 | - | The coolant temperature of the engine is too high. |
| P022200 | - | Position sensor 2 for the throttle valve has a short circuit to ground. |
| P022300 | - | Position sensor 2 for the throttle valve has a short circuit to positive. |
| P026100 | - | The fuel injector (cylinder 1) has a short circuit to ground. |
| P026200 | - | The fuel injector (cylinder 1) has a short circuit to positive. |
| P026400 | - | The fuel injector (cylinder 2) has a short circuit to ground. |
| P026500 | - | The fuel injector (cylinder 2) has a short circuit to positive. |
| P026700 | - | The fuel injector (cylinder 3) has a short circuit to ground. |
| P026800 | - | The fuel injector (cylinder 3) has a short circuit to positive. |
| P027000 | - | The fuel injector (cylinder 4) has a short circuit to ground. |
| P027100 | - | The fuel injector (cylinder 4) has a short circuit to positive. |
| P027300 | - | The fuel injector (cylinder 5) has a short circuit to ground. |
| P027400 | - | The fuel injector (cylinder 5) has a short circuit to positive. |
| P027600 | - | The fuel injector (cylinder 6) has a short circuit to ground. |
| P027700 | - | The fuel injector (cylinder 6) has a short circuit to positive. |
| P030085 | - | Combustion misfiring has been detected. There is a signal above the permissible limit value. |
| P030185 | - | Combustion misfiring of cylinder 1 has been detected. There is a signal above the permissible limit value. |
| P030285 | - | Combustion misfiring of cylinder 2 has been detected. There is a signal above the permissible limit value. |
| P030385 | - | Combustion misfiring of cylinder 3 has been detected. There is a signal above the permissible limit value. |
| P030485 | - | Combustion misfiring of cylinder 4 has been detected. There is a signal above the permissible limit value. |
| P030585 | - | Combustion misfiring of cylinder 5 has been detected. There is a signal above the permissible limit value. |
| P030685 | - | Combustion misfiring of cylinder 6 has been detected. There is a signal above the permissible limit value. |
| P032400 | - | The knock control has a malfunction. |
| P032711 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P032714 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P032784 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a signal below the permissible limit value. |
| P032812 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P032815 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P032885 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a signal above the permissible limit value. |
| P033211 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground. |
| P033214 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P033284 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a signal below the permissible limit value. |
| P033312 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive. |
| P033315 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a short circuit to positive or an open circuit. |
| P033385 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a signal above the permissible limit value. |
| P033600 | - | Position sensor 1 for the crankshaft has a malfunction. |
| P033900 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. |
| P034100 | - | The position sensor for the intake camshaft (cylinder bank 1) has a malfunction. |
| P034200 | - | The position sensor for the intake camshaft (cylinder bank 1) has a short circuit to ground. |
| P034300 | - | The position sensor for the intake camshaft (cylinder bank 1) has a short circuit to positive. |
| P034600 | - | The position sensor for the intake camshaft (cylinder bank 2) has a malfunction. |
| P034700 | - | The position sensor for the intake camshaft (cylinder bank 2) has a short circuit to ground. |
| P034800 | - | The position sensor for the intake camshaft (cylinder bank 2) has a short circuit to positive. |
| P035004 | - | The control unit has a malfunction. |
| P035005 | - | The control unit has a malfunction. |
| P035006 | - | The control unit has a malfunction. |
| P035012 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. |
| P035112 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. The limit value for current has been exceeded. |
| P035114 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is a short circuit to ground or an open circuit. |
| P035212 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. The limit value for current has been exceeded. |
| P035214 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. The limit value for current has not been attained. |
| P035312 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. The limit value for current has been exceeded. |
| P035314 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. The limit value for current has not been attained. |
| P035414 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. The limit value for current has not been attained. |
| P035512 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. The limit value for current has been exceeded. |
| P035514 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. The limit value for current has not been attained. |
| P035612 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. The limit value for current has been exceeded. |
| P035614 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is a short circuit to ground or an open circuit. |
| P036600 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a malfunction. |
| P036700 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to ground. |
| P036800 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to positive. |
| P038700 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to ground. |
| P038800 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to positive. |
| P039100 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a malfunction. |
| P039200 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a short circuit to ground. |
| P039300 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a short circuit to positive. |
| P041300 | - | Secondary air valve 1 has an open circuit. |
| P041800 | - | This error code can be ignored and erased. |
| P041F00 | - | Secondary air valve 1 has a short circuit to ground. |
| P042000 | - | The efficiency of the catalytic converter (cylinder bank 1) is not sufficient. |
| P043000 | - | The efficiency of the catalytic converter (cylinder bank 2) is not sufficient. |
| P044200 | - | A fine leak in the evaporative emission control system was detected. |
| P044209 | - | A fine leak in the evaporative emission control system was detected. |
| P044400 | - | The purge valve of the evaporative emission control system has an open circuit. |
| P044F00 | - | Secondary air valve 1 has a short circuit to positive. |
| P045101 | - | This error code can be ignored and erased. |
| P045111 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to ground. |
| P045112 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to positive. |
| P045129 | - | This error code can be ignored and erased. |
| P045200 | - | The pressure sensor/pressure switch of the evaporative emission control system has a sporadic malfunction. |
| P045300 | - | The pressure sensor/pressure switch of the evaporative emission control system has a sporadic malfunction. |
| P045500 | - | A gross leak in the evaporative emission control system was detected. |
| P045600 | - | A very fine leak in the evaporative emission control system was detected. |
| P045609 | - | A very fine leak in the evaporative emission control system was detected. There is a component fault. |
| P045700 | - | Leakage in the evaporative emission control system was detected (tank cap missing). |
| P04577A | - | Leakage in the evaporative emission control system was detected (tank cap missing). Leakage or a defective seal was detected. |
| P045800 | - | The purge valve of the evaporative emission control system has a short circuit to ground. |
| P045900 | - | The purge valve of the evaporative emission control system has a short circuit to positive. |
| P046185 | - | The left fuel level sensor has an electrical fault. There is a signal above the permissible limit value. |
| P048000 | - | The output of electric fan 1 has an electrical fault or an open circuit. |
| P048300 | - | Electric fan has a malfunction. |
| P048329 | - | Electric fan has a malfunction. There is an invalid signal. |
| P049100 | - | The air flow of the secondary air system (cylinder bank 1) is too low. |
| P049200 | - | The air flow of the secondary air system (cylinder bank 2) is too low. |
| P049400 | - | The fan rpm is too low. |
| P049600 | - | The purge flow of the evaporative emission control system is too high. |
| P049700 | - | The purge flow of the of evaporative emission control system is too low. |
| P050609 | - | |
| P050709 | - | The idle speed is too high during catalytic converter warm-up. There is a component fault. |
| P050A00 | - | Idle speed control implausible |
| P050A17 | - | Voltage limit value exceeded, idle control incorrect |
| P050B00 | - | Ignition angle setting has a malfunction during a cold start. |
| P052A00 | - | COLD START : The position of the intake camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P052C00 | - | COLD START : The position of the intake camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P053100 | - | The refrigerant pressure sensor has a malfunction. |
| P053200 | - | The refrigerant pressure sensor has a malfunction. |
| P053300 | - | The refrigerant pressure sensor has a malfunction. |
| P053400 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P053600 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P053604 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P053700 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P053800 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P053817 | - | Fault code in N19/4 (Electric refrigerant compressor control unit) control unit |
| P054A00 | - | COLD START : The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P054C00 | - | COLD START : The position of the exhaust camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P056200 | - | The on-board power supply voltage is too low. |
| P056201 | - | The on-board power supply voltage is too low. |
| P056216 | P0562 | The on-board power supply voltage is too low. The limit value for electrical voltage has not been attained. (P0562) |
| P056300 | - | The on-board power supply voltage is too high. |
| P056317 | - | The on-board power supply voltage is too high. |
| P057129 | - | Switch 'Brake light' has a malfunction. There is an invalid signal. |
| P059700 | - | The coolant thermostat has an electrical fault or open circuit. |
| P059800 | - | The coolant thermostat has a short circuit to ground. |
| P059900 | - | The coolant thermostat has a short circuit to positive. |
| P060000 | - | Oxygen sensors 1 (cylinder banks 1 and 2) have been swapped. |
| P060416 | - | There is an internal control unit fault in the RAM memory. The limit value for electrical voltage has not been attained. |
| P060417 | - | There is an internal control unit fault in the RAM memory. The limit value for electrical voltage has been exceeded. |
| P060700 | - | The control unit has a malfunction. |
| P060702 | - | The control unit has a malfunction. There is a general signal fault. |
| P060704 | - | The control unit has a malfunction. There is an internal fault. |
| P060716 | - | The control unit has a malfunction. The limit value for electrical voltage has not been attained. |
| P060741 | - | The control unit has a malfunction. There is a general checksum error. |
| P060748 | - | The control unit has a malfunction. There is an error in the control memory. |
| P060C02 | - | There is an internal control unit fault in the central processing unit. There is a general signal fault. |
| P060C04 | - | There is an internal control unit fault in the central processing unit. There is an internal fault. |
| P060C09 | - | There is an internal control unit fault in the central processing unit. There is a component fault. |
| P060C17 | - | There is an internal control unit fault in the central processing unit. The limit value for electrical voltage has been exceeded. |
| P060C29 | - | There is an internal control unit fault in the central processing unit. There is an invalid signal. |
| P060C47 | - | There is an internal control unit fault in the central processing unit. There is a runtime error. |
| P060C62 | - | There is an internal control unit fault in the central processing unit. The signal comparison is faulty. |
| P060C64 | - | There is an internal control unit fault in the central processing unit. There is an implausible signal. |
| P061A28 | - | The torque control of the control unit has a malfunction. The signal offset is outside the permissible range. |
| P061A81 | - | The torque control of the control unit has a malfunction. Incorrect data were received. |
| P061A94 | - | The torque control of the control unit has a malfunction. There is an unexpected instruction. |
| P061B05 | - | The torque calculation of the control unit has a malfunction. There is a programming fault. |
| P061B06 | - | The torque calculation of the control unit has a malfunction. There is an algorithm fault. |
| P061B85 | - | The torque calculation of the control unit has a malfunction. There is a signal above the permissible limit value. |
| P061C00 | - | There is an internal control unit fault affecting the calculation of the engine speed. |
| P061C02 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is a general signal fault. |
| P061C04 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is an internal fault. |
| P061C08 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is a signal fault or the message is faulty. |
| P061D46 | - | There is an internal control unit fault in the monitoring function for the air mass. There is an error in the calibration or parameterization memory. |
| P061D62 | - | There is an internal control unit fault in the monitoring function for the air mass. The signal comparison is faulty. |
| P061D64 | - | There is an internal control unit fault in the monitoring function for the air mass. There is an implausible signal. |
| P061E29 | - | There is an internal control unit fault in the monitoring function for the signal of switch 'Brake light'. There is an invalid signal. |
| P062700 | - | The output for the fuel pump has an electrical fault or open circuit. |
| P062713 | - | The output for the fuel pump has an electrical fault or open circuit. There is an open circuit. |
| P062800 | - | The output for the fuel pump has a short circuit to ground. |
| P062811 | - | The output for the fuel pump has a short circuit to ground. There is a short circuit to ground. |
| P062900 | - | The output for the fuel pump has a short circuit to positive. |
| P062A00 | - | The output of the fuel pump is implausible. |
| P063804 | - | The output for the throttle valve actuator (cylinder bank 1) has a malfunction. There is an internal fault. |
| P064104 | - | Output 1 for power supply to the sensors has an electrical fault or open circuit. There is an internal fault. |
| P064501 | - | The output for the magnetic clutch of the air conditioning has a malfunction. There is a general electrical fault. |
| P064504 | - | The output for the magnetic clutch of the air conditioning has a malfunction. There is an internal fault. |
| P064D04 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an internal fault. |
| P064D84 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is a signal below the permissible limit value. |
| P064D85 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is a signal above the permissible limit value. |
| P064D86 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an incorrect signal. |
| P064E04 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is an internal fault. |
| P064E84 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is a signal below the permissible limit value. |
| P064E85 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is a signal above the permissible limit value. |
| P064E86 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is an incorrect signal. |
| P065100 | - | Output 2 for the power supply of the sensors has an electrical fault or an open circuit. |
| P065104 | - | Output 2 for the power supply of the sensors has an electrical fault or an open circuit. There is an internal fault. |
| P065B00 | - | The alternator has a malfunction. |
| P066000 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has an electrical fault or open circuit. |
| P066100 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has a short circuit to ground. |
| P066200 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has a short circuit to positive. |
| P069100 | - | The output of electric fan 1 has a short circuit to ground. |
| P069200 | - | The output of electric fan 1 has a short circuit to positive. |
| P069704 | - | Output 3 for the reference voltage of the sensors has an electrical fault or an open circuit. There is an internal fault. |
| P06A009 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06A016 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06A017 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06A019 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06A064 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06A085 | - | Failure of electric refrigerant compressor due to excessive torque |
| P06DA00 | - | The actuation of the valve of the oil pump in the combustion engine has an electrical fault or open circuit. |
| P06DB00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to ground. |
| P06DC00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to positive. |
| P0A011C | - | The temperature sensor for the low-temperature circuit has a malfunction. The voltage value is outside the permissible range. |
| P0A0184 | - | The temperature sensor for the low-temperature circuit has a malfunction. There is a signal below the permissible limit value. |
| P0A0185 | - | The temperature sensor for the low-temperature circuit has a malfunction. There is a signal above the permissible limit value. |
| P0A0200 | - | The temperature sensor for the low-temperature circuit has a short circuit to ground. |
| P0A0300 | - | The temperature sensor for the low-temperature circuit has a short circuit to positive. |
| P0A0500 | - | The actuation of the circulation pump for the low-temperature circuit has an open circuit. |
| P0A0600 | - | The actuation of the circulation pump for the low-temperature circuit has a short circuit to ground. |
| P0A0700 | - | The actuation of the circulation pump for the low-temperature circuit has a short circuit to positive. |
| P0A0800 | - | This error code can be ignored and erased. |
| P0A0B00 | - | This error code can be ignored and erased. |
| P0A1200 | - | This error code can be ignored and erased. |
| P0A1300 | - | This error code can be ignored and erased. |
| P0A7D00 | - | The charge level of the high-voltage battery module is low. |
| P0A7D18 | - | The charge level of the high-voltage battery module is low. The limit value for current has not been attained. |
| P0A9400 | - | This error code can be ignored and erased. |
| P0A9408 | - | This error code can be ignored and erased. |
| P0A9429 | - | This error code can be ignored and erased. |
| P0AC000 | - | Battery current sensor 'A' in the high-voltage battery module has a malfunction. |
| P0ADA00 | - | The actuation of contact 'Positive terminal' of the contactor in the high-voltage battery has a malfunction. |
| P0C3200 | - | The hybrid system has a malfunction. |
| P110126 | - | The signal change rate is below the permissible limit value. |
| P110127 | - | Ratio of HFM signal to intake manifold pressure is too high. |
| P111717 | - | There is an internal control unit fault in the central processing unit. |
| P111804 | - | There is an internal control unit fault in the central processing unit. There is an internal fault. |
| P111947 | - | There is an internal control unit fault in the central processing unit. There is a runtime error. |
| P134527 | - | Hot film mass air flow sensor 1 has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P134626 | - | Hot film mass air flow sensor 1 has a sporadic malfunction. The signal change rate is below the permissible limit value. |
| P134700 | - | Mass air flow sensor 1 has a short circuit to ground. |
| P13EA00 | - | The ignition angle setting has a malfunction during cold starting (partial load operation). |
| P167000 | - | Torque control has a malfunction. |
| P167004 | - | Torque control has a malfunction. |
| P167085 | - | The load limit is active. |
| P199907 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a mechanical fault. |
| P1A8802 | - | General signal failure. Discharging of intermediate circuit failed |
| P206600 | - | The right fuel level sensor has an electrical fault. |
| P207204 | - | The throttle valve is blocked due to ice. There is an internal fault. |
| P207284 | - | The throttle valve is blocked due to ice. There is a signal below the permissible limit value. |
| P207285 | - | The throttle valve is blocked due to ice. There is a signal above the permissible limit value. |
| P207286 | - | The throttle valve is blocked due to ice. There is an incorrect signal. |
| P208800 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to ground. |
| P208900 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to positive. |
| P209000 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to ground. |
| P209100 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to positive. |
| P209200 | - | Actuator 'Intake camshaft' (cylinder bank 2) has a short circuit to ground. |
| P209300 | - | Actuator 'Intake camshaft' (cylinder bank 2) has a short circuit to positive. |
| P209400 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has a short circuit to ground. |
| P209500 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has a short circuit to positive. |
| P209600 | - | The mixture is too lean downstream of the catalytic converter (cylinder bank 1). |
| P209700 | - | The mixture is too rich downstream of the catalytic converter (cylinder bank 1). |
| P20B100 | - | Output for coolant shutoff valve has an electrical fault or open circuit. |
| P20B300 | - | Output for coolant shutoff valve has a short circuit to ground. |
| P20B400 | - | Output for coolant shutoff valve has a short circuit to positive. |
| P210000 | - | The throttle valve actuator has an electrical fault or open circuit. |
| P210013 | - | The throttle valve actuator has an electrical fault or open circuit. There is an open circuit. |
| P210100 | - | The throttle valve actuator has a malfunction. |
| P210128 | - | The throttle valve actuator has a malfunction. The signal offset is outside the permissible range. |
| P210129 | - | The throttle valve actuator has a malfunction. There is an invalid signal. |
| P210184 | - | The throttle valve actuator has a malfunction. There is a signal below the permissible limit value. |
| P210185 | - | The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. |
| P210200 | - | The throttle valve actuator has a short circuit to ground. |
| P210211 | - | The throttle valve actuator has a short circuit to ground. There is a short circuit to ground. |
| P210300 | - | The throttle valve actuator has a short circuit to positive. |
| P210312 | - | The throttle valve actuator has a short circuit to positive. There is a short circuit to positive. |
| P211100 | - | The throttle valve is jammed open. |
| P211200 | - | The throttle valve is jammed closed. |
| P212200 | - | Position sensor 1 for the accelerator pedal has a short circuit to ground. |
| P212300 | - | Position sensor 1 for the accelerator pedal has a short circuit to positive |
| P212711 | - | Position sensor 2 for the accelerator pedal has a short circuit to ground. There is a short circuit to ground. |
| P212800 | - | Position sensor 2 for the accelerator pedal has a short circuit to positive |
| P213500 | - | The values from the position sensors of the throttle valve are implausible in relation to each other. |
| P213529 | - | The values from the position sensors of the throttle valve are implausible in relation to each other. There is an invalid signal. |
| P213700 | - | The values from the position sensors of the throttle valve are implausible in relation to each other. |
| P213800 | - | The values from the position sensors of the accelerator pedal are implausible in relation to each other. |
| P213804 | - | The values from the position sensors of the accelerator pedal are implausible in relation to each other. There is an internal fault. |
| P217607 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a mechanical fault. |
| P217609 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a component fault. |
| P217616 | - | Adaptation of the idle position of the throttle valve actuator was not performed. The limit value for electrical voltage has not been attained. |
| P217617 | - | Adaptation of the idle position of the throttle valve actuator was not performed. The limit value for electrical voltage has been exceeded. |
| P217700 | - | The mixture (cylinder bank 1) is too lean in partial load operation. |
| P217800 | - | The mixture (cylinder bank 1) is too rich in partial load operation. |
| P217900 | - | The mixture (cylinder bank 2) is too lean in partial load operation. |
| P218000 | - | The mixture (cylinder bank 2) is too lean in partial load operation. |
| P218127 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P218226 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is below the permissible limit value. |
| P218700 | - | The mixture (cylinder bank 1) is too lean at idle speed. |
| P218800 | - | The mixture (cylinder bank 1) is too rich at idle speed. |
| P218900 | - | The mixture (cylinder bank 2) at idle is too lean. |
| P219000 | - | The mixture (cylinder bank 2) at idle is too rich. |
| P219585 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Lean'. There is a signal above the permissible limit value. |
| P219684 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Rich'. There is a signal below the permissible limit value. |
| P219785 | - | The signal from oxygen sensor 1 (cylinder bank 2) is shifted towards 'Lean'. There is a signal above the permissible limit value. |
| P219884 | - | The signal from oxygen sensor 1 (cylinder bank 2) is shifted towards 'Rich'. There is a signal below the permissible limit value. |
| P222700 | - | The ambient pressure sensor has a malfunction. |
| P222784 | - | The ambient pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P222785 | - | The ambient pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P222786 | - | The ambient pressure sensor has a malfunction. There is an incorrect signal. |
| P222800 | - | The ambient pressure sensor has a short circuit to ground. |
| P222900 | - | The ambient pressure sensor has a short circuit to positive. |
| P223200 | - | The signal line of oxygen sensor 2 (cylinder bank 1) and the electric heater circuit have a short circuit to each other. |
| P223500 | - | The signal line of oxygen sensor 2 (cylinder bank 2) and the electric heater circuit have a short circuit to each other. |
| P223784 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. There is a signal below the permissible limit value. |
| P223785 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. There is a signal above the permissible limit value. |
| P223786 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. There is an incorrect signal. |
| P224084 | - | The pump current connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. There is a signal below the permissible limit value. |
| P224085 | - | The pump current connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. There is a signal above the permissible limit value. |
| P224086 | - | The pump current connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. There is an incorrect signal. |
| P224300 | - | The reference voltage connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P224700 | - | The reference voltage connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P225700 | - | The actuation of secondary air system 1 (air pump) has a short circuit to ground. |
| P225800 | - | The actuation of secondary air system 1 (air pump) has a short circuit to positive. |
| P227000 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Lean'. |
| P227100 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Rich'. |
| P227200 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Lean'. |
| P227300 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Rich'. |
| P227900 | - | A leak was detected in the intake air system. |
| P230000 | - | The actuation of ignition coil 1 has a short circuit to ground. |
| P230013 | - | The actuation of ignition coil 1 has a short circuit to ground. There is an open circuit. |
| P230100 | - | The actuation of ignition coil 1 has a short circuit to positive. |
| P230300 | - | The actuation of ignition coil 2 has a short circuit to ground. |
| P230313 | - | The actuation of ignition coil 2 has a short circuit to ground. There is an open circuit. |
| P230400 | - | The actuation of ignition coil 2 has a short circuit to positive. |
| P230600 | - | The actuation of ignition coil 3 has a short circuit to ground. |
| P230613 | - | The actuation of ignition coil 3 has a short circuit to ground. There is an open circuit. |
| P230700 | - | The actuation of ignition coil 3 has a short circuit to positive. |
| P230900 | - | The actuation of ignition coil 4 has a short circuit to ground. |
| P230913 | - | The actuation of ignition coil 4 has a short circuit to ground. There is an open circuit. |
| P231000 | - | The actuation of ignition coil 4 has a short circuit to positive. |
| P231200 | - | The actuation of ignition coil 5 has a short circuit to ground. |
| P231213 | - | The actuation of ignition coil 5 has a short circuit to ground. There is an open circuit. |
| P231300 | - | The actuation of ignition coil 5 has a short circuit to positive. |
| P231500 | - | The actuation of ignition coil 6 has a short circuit to ground. |
| P231513 | - | The actuation of ignition coil 6 has a short circuit to ground. There is an open circuit. |
| P231600 | - | The actuation of ignition coil 6 has a short circuit to positive. |
| P240000 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240013 | - | The switchover valve to the reference duct in the diagnostic module of the evaporative emission control system has a malfunction. There is an open circuit. |
| P240100 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240111 | - | The switchover valve to the reference duct in the diagnostic module of the evaporative emission control system has a malfunction. There is a short circuit to ground. |
| P240200 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P240212 | - | The switchover valve to the reference duct in the diagnostic module of the evaporative emission control system has a malfunction. There is a short circuit to positive. |
| P240400 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. |
| P240418 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has not been attained. |
| P240419 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has been exceeded. |
| P24041C | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The voltage value is outside the permissible range. |
| P240700 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. |
| P240A00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240B00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240C00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P241400 | - | The signal from oxygen sensor 1 (cylinder bank 1) is implausible. |
| P241500 | - | The signal from oxygen sensor 1 (cylinder bank 2) is implausible. |
| P241900 | - | This error code can be ignored and erased. |
| P242000 | - | This error code can be ignored and erased. |
| P244000 | - | The secondary air valve (cylinder bank 1) is jammed open. |
| P244200 | - | The secondary air valve (cylinder bank 2) is jammed open. |
| P245000 | - | This error code can be ignored and erased. |
| P245100 | - | This error code can be ignored and erased. |
| P250900 | - | The power supply at the input of the control unit 'combustion engine' has a sporadic malfunction. |
| P251900 | - | Implausible data were received from the air conditioning. |
| P253900 | - | The pressure sensor of the low-pressure fuel circuit has a malfunction. |
| P254000 | - | The signal for the pressure sensor of the low-pressure fuel circuit is implausible. |
| P254100 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to ground. |
| P254200 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to positive. |
| P256171 | - | Implausible data were received from the air conditioning. |
| P256804 | - | The PremAir sensor has a malfunction. There is an internal fault. |
| P256809 | - | The PremAir sensor has a malfunction. There is a component fault. |
| P256885 | - | The PremAir sensor has a malfunction. There is a signal above the permissible limit value. |
| P256900 | - | The PremAir sensor has a short circuit to ground. |
| P257000 | - | The PremAir sensor has a short circuit to positive. |
| P257100 | - | The PremAir sensor has a sporadic malfunction. |
| P257D00 | - | Contact switch 1 'Engine hood' has a malfunction. |
| P262600 | - | The trimming resistor connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P262900 | - | The trimming resistor connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P2A0000 | - | Oxygen sensor 1 (cylinder bank 1) has a malfunction. |
| P2A0085 | - | Oxygen sensor 1 (cylinder bank 1) has a malfunction. There is a signal above the permissible limit value. |
| P2A0300 | - | Oxygen sensor 1 (cylinder bank 2) has a malfunction. |
| P2A0385 | - | Oxygen sensor 1 (cylinder bank 2) has a malfunction. There is a signal above the permissible limit value. |
| U002887 | - | CAN bus OFF : Short circuit Engine CAN bus |
| U003787 | - | LIN bus OFF |
| U004600 | - | Drive train CAN bus OFF fault |
| U007400 | - | Hybrid CAN bus OFF fault |
| U010F00 | - | Communication with the 'electric A/C compressor' control unit has a malfunction. |
| U010F87 | - | Communication with the 'electric A/C compressor' control unit has a malfunction. The message is missing. |
| U011000 | - | Communication with control unit 'Electric machine A' has a malfunction. |
| U011081 | - | Communication with control unit 'Electric machine A' has a malfunction. Incorrect data were received. |
| U011087 | - | Communication with control unit 'Electric machine A' has a malfunction. The message is missing. |
| U011100 | - | Communication with control unit 'Battery' has a malfunction. |
| U015100 | - | Communication with the supplemental restraint system has a malfunction. |
| U029800 | - | Hybrid CAN bus OFF fault |
| U029881 | - | Hybrid CAN bus OFF fault |
| U029A81 | - | Hybrid CAN bus OFF fault |
| U029A87 | - | Hybrid CAN bus OFF fault |
| U029A88 | - | Hybrid CAN bus OFF fault |
| U029B00 | - | This error code can be ignored and erased. |
| U041100 | - | Invalid data received from engine control module A |
| U042400 | - | Implausible data were received from the air conditioning. |
| U042481 | - | Implausible data were received from the air conditioning. Incorrect data were received. |
| U042486 | - | Implausible data were received from the air conditioning. There is an incorrect signal. |
| U059400 | - | Implausible data were received from control unit ""Hybrid system"". |
| U150E64 | - | The hybrid system has a malfunction. |
| U151200 | - | Communication between control units 'Air conditioning' and 'Battery' has a malfunction. |
| U151300 | - | Communication between control units 'Air conditioning' and 'Instrument cluster' has a malfunction. |
| U151387 | - | Communication between control units 'Air conditioning' and 'Instrument cluster' has a malfunction. The message is missing. |
| U151400 | - | Communication with the air conditioning has a malfunction. |
| U300E00 | - | The CAN signal from circuit 15 does not match the signal via the hardware line. (Signal via hardware line = 0) |
| U301100 | - | The CAN signal from circuit 15 does not match the signal via the hardware line. (Signal via CAN = 0) |