Engine Control DTCS
ENGINE CONTROL DTCS (CDI60LS ENGINE 642)
| MB DTC | Generic DTC | Description |
|---|---|---|
| 100200 | P010F | The difference in the air mass measurement is outside the defined limits. |
| 100700 | P0101 | The upper limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 100800 | P010B | The upper limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 100900 | P0101 | The lower limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 100A00 | P010B | The lower limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 100B00 | P0100 | The upper limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 100C00 | P010A | The upper limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 100D00 | P0100 | The lower limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 100E00 | P010A | The lower limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 100F00 | P0103 | The upper limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 101000 | P010D | The upper limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 101100 | P0102 | The lower limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 101200 | P010C | The lower limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 101300 | P0103 | The upper limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 101400 | P010D | The upper limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 101500 | P0102 | The lower limit value of component B2/7 (Right hot film mass air flow sensor) has been reached. |
| 101600 | P010C | The lower limit value of component B2/6 (Left hot film mass air flow sensor) has been reached. |
| 101700 | P0101 | Component B2/7 (Right hot film mass air flow sensor) has a plausibility error. |
| 101800 | P010B | Component B2/6 (Left hot film mass air flow sensor) has a plausibility error. |
| 101900 | P0101 | Component B2/7 (Right hot film mass air flow sensor) has a plausibility error. |
| 101A00 | P010B | Component B2/6 (Left hot film mass air flow sensor) has a plausibility error. |
| 101B00 | P0123 | The signal voltage of sensor 1 of component B37 (Accelerator pedal sensor) is too high. |
| 101C00 | P0122 | The signal voltage of sensor 1 of component B37 (Accelerator pedal sensor) is too low. |
| 101D00 | P0223 | The signal voltage of sensor 2 of component B37 (Accelerator pedal sensor) is too high. |
| 101E00 | P0222 | The signal voltage of sensor 2 of component B37 (Accelerator pedal sensor) is too low. |
| 101F00 | P2135 | Component B37 (Accelerator pedal sensor) has a plausibility error. |
| 102000 | P0121 | The reference voltage of component B37 (Accelerator pedal sensor) is implausible. |
| 102100 | P062F | Control module has an internal error. |
| 102900 | - | The water content of the fuel filter has reached the upper limit value. |
| 102B00 | - | This function is not yet supported by the control unit. |
| 102C00 | - | The signal from component B76/1 (Condensation sensor for fuel filter with heating element) is faulty. |
| 102D00 | P0605 | Control module has an internal error. |
| 102E00 | U0426 | The signal of circuit 15 is implausible. |
| 102F00 | U0426 | The signal of circuit 15 is implausible. |
| 103100 | P0401 | The positive control deviation of exhaust gas recirculation control is too high. |
| 103200 | P0402 | The negative control deviation of exhaust gas recirculation control is too high. |
| 103300 | P0401 | The positive control deviation of exhaust gas recirculation control during regeneration is too high. |
| 103400 | P0402 | The negative control deviation of exhaust gas recirculation control during regeneration is too high. |
| 103500 | P2413 | Timeout during transition from regeneration to normal operation |
| 103D00 | - | The dynamic test of component B11/4 (Coolant temperature sensor) was not successful. |
| 103E00 | - | The signal voltage of component B11/4 (Coolant temperature sensor) is too high. |
| 103F00 | - | The signal voltage of component B11/4 (Coolant temperature sensor) is too low. |
| 104300 | P0806 | Component S40/3 (Clutch pedal switch) has a plausibility error. |
| 104400 | U0402 | The signal from component S40/3 (Clutch pedal switch) is faulty. |
| 104C00 | P042A | The difference between the current measurement and the most recent measurement of the exhaust gas temperature from component B19 (Catalytic converter temperature sensor) is too great. |
| 104D00 | P042A | The difference between the current measurement and the most recent measurement of the exhaust gas temperature from component B19/9 (Temperature sensor upstream of diesel particulate filter) is too great. |
| 104F00 | P245A | Component Y85 (Exhaust gas recirculation cooler bypass switchover valve) has Open circuit. |
| 105000 | P245D | Component Y85 (Exhaust gas recirculation cooler bypass switchover valve) has Short circuit to positive. |
| 105100 | P245C | Component Y85 (Exhaust gas recirculation cooler bypass switchover valve) has Short circuit to ground. |
| 105500 | P0403 | Component Y27/9 (Left EGR positioner) has Open circuit. |
| 105600 | P0490 | Component Y27/9 (Left EGR positioner) has Short circuit to positive. |
| 105700 | P0489 | Component Y27/9 (Left EGR positioner) has Short circuit to ground. |
| 105800 | U0418 | The requirements of control unit N30/4 (Electronic Stability Program control unit) for increasing the idle speed are not fulfilled. |
| 106100 | P2BAD | The upper limit value for long-term adaptation of the SCR exhaust aftertreatment system was exceeded. |
| 106200 | P2BAA | The lower limit value for long-term adaptation of the SCR exhaust aftertreatment system was dropped below. |
| 106300 | P20EE | Efficiency of SCR catalytic converter : Effect is insufficient. |
| 106500 | P20EE | Efficiency of SCR catalytic converter : Effect is insufficient. |
| 106700 | P2BA7 | Engine start is not possible. |
| 106900 | P0507 | The engine speed is too high. |
| 106A00 | P0506 | The engine speed is too low. |
| 106B00 | P0607 | Component R48 (Coolant thermostat heating element) has excess temperature. |
| 106C00 | P0420 | The efficiency of the catalytic converter (cylinder bank 1) is not sufficient. |
| 106D00 | P1999 | This function is not available at present. |
| 107A00 | P0128 | This function is not available at present. |
| 107C00 | P0071 | Plausibility error between signal of temperature sensor in intake pipe and signal of outside temperature sensor |
| 107E00 | - | The upper limit value of component B28/8 (Differential pressure sensor (DPF)) has been reached. |
| 107F00 | P2080 | The upper limit value of component B19 (Catalytic converter temperature sensor) has been exceeded. |
| 108000 | P0426 | The upper limit value of component B19/9 (Temperature sensor upstream of diesel particulate filter) has been exceeded. |
| 108100 | - | The lower limit value of component B28/8 (Differential pressure sensor (DPF)) has been reached. |
| 108200 | P2080 | The lower limit value of component B19 (Catalytic converter temperature sensor) was dropped below/not reached. |
| 108300 | P0426 | The lower limit value of component B19/9 (Temperature sensor upstream of diesel particulate filter) was dropped below/not reached. |
| 108400 | P2229 | The signal voltage of component Atmospheric pressure sensor is too high. |
| 108500 | P2228 | The signal voltage of component Atmospheric pressure sensor is too low. |
| 108600 | P0073 | The signal voltage of component B14 (Outside temperature sensor) is too high. |
| 108700 | P0072 | The signal voltage of component B14 (Outside temperature sensor) is too low. |
| 108800 | P0341 | The signal from component B6/1 (Camshaft Hall sensor) is faulty. |
| 108900 | P0340 | No signal from component B6/1 (Camshaft Hall sensor) |
| 108A00 | P0336 | No signal from component B70 (Crankshaft Hall sensor) |
| 108B00 | P0335 | The signal from component B70 (Crankshaft Hall sensor) is faulty. |
| 108C00 | P042B | The difference between the measured temperature and the calculated temperature of component B19 (Catalytic converter temperature sensor) is too great. |
| 108D00 | P042B | The difference between the measured temperature and the calculated temperature of component B19/9 (Temperature sensor upstream of diesel particulate filter) is too great. |
| 108E00 | P200E | The difference between the measured exhaust gas temperature from component B19 (Catalytic converter temperature sensor) and from component B19/9 (Temperature sensor upstream of diesel particulate filter) is too great. |
| 108F00 | P0607 | Component Y94 (Quantity control valve) has excess temperature. |
| 109000 | P0607 | Component R48 (Coolant thermostat heating element) has excess temperature. |
| 109100 | - | Component Starter has excess temperature. |
| 109800 | - | The signal voltage of component B50 (Fuel temperature sensor) is too high. |
| 109900 | - | The signal voltage of component B50 (Fuel temperature sensor) is too low. |
| 109A00 | P065A | Component G2 (generator) has a malfunction. |
| 109C00 | P0088 | The maximum rail pressure was exceeded. |
| 109D00 | P0088 | The minimum rail pressure was dropped below/not reached. |
| 109E00 | P0088 | The minimum rail pressure was dropped below/not reached. |
| 109F00 | P0088 | The maximum rail pressure was exceeded. |
| 10A000 | - | The number of combustion misfires at cylinder 6 is too high. |
| 10A100 | - | The number of combustion misfires at cylinder 1 is too high. |
| 10A200 | - | The number of combustion misfires at cylinder 4 is too high. |
| 10A300 | - | The number of combustion misfires at cylinder 2 is too high. |
| 10A400 | - | The number of combustion misfires at cylinder 5 is too high. |
| 10A500 | - | The number of combustion misfires at cylinder 3 is too high. |
| 10A600 | - | The number of combustion misfires at cylinder 6 is too high. |
| 10A800 | - | The signal of component 'B28/14 (Crankcase ventilation system differential pressure sensor)' is implausible. |
| 10A900 | - | The signal of component 'B28/14 (Crankcase ventilation system differential pressure sensor)' is implausible. |
| 10AA00 | - | The signal of component 'B28/14 (Crankcase ventilation system differential pressure sensor)' is implausible. |
| 10AB00 | - | The signal of component 'B28/14 (Crankcase ventilation system differential pressure sensor)' is implausible. |
| 10AC00 | P242B | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 10AD00 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10AE00 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10AF00 | P242B | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 10B000 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10B100 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10B200 | P2080 | Component B19/11 (Temperature sensor upstream of turbocharger) has a plausibility error. |
| 10B300 | P0426 | Component B19 (TWC temperature sensor) has a plausibility error. |
| 10B400 | P042B | Component B19/9 (Temperature sensor upstream of diesel particulate filter) has a plausibility error. |
| 10B500 | P242B | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 10B600 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10B700 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10B800 | P20E3 | Component Exhaust temperature sensor has a plausibility error. |
| 10B900 | P242B | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 10BA00 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10BE00 | P242B | There is an internal fault in component B16/15 (Temperature sensor upstream of SCR catalytic converter). |
| 10BF00 | P0480 | The control line to component M4/7 (Engine and AC electric suction fan with integrated control) has Open circuit. |
| 10C000 | P0607 | Component M4/7 (Engine and AC electric suction fan with integrated control) has Excess temperature. |
| 10C100 | P0692 | The control line to component M4/7 (Engine and AC electric suction fan with integrated control) has Short circuit to positive. |
| 10C200 | P0691 | The control line to component M4/7 (Engine and AC electric suction fan with integrated control) has Short circuit to ground. |
| 10C700 | P2004 | Component M55 (Inlet port shutoff motor) sticks or component B96/2 (Right intake port shutoff end position sensor) is defective. |
| 10C800 | P2005 | Component M55 (Inlet port shutoff motor) sticks or component B96/1 (Left intake port shutoff end position sensor) is defective. |
| 10CA00 | P2006 | Component M55 (Inlet port shutoff motor) sticks or component B96/2 (Right intake port shutoff end position sensor) is defective. |
| 10CB00 | P2007 | Component M55 (Inlet port shutoff motor) sticks or component B96/1 (Left intake port shutoff end position sensor) is defective. |
| 10CC00 | P245B | The difference between the measured temperature and the calculated temperature of component Y85 (Exhaust gas recirculation cooler bypass switchover valve) is too great. |
| 10CD00 | P2457 | Check component Exhaust gas recirculation cooler. |
| 10CE00 | P0607 | Control module has an internal error. |
| 10D100 | P0194 | The control deviation during rail pressure regulation is too high. |
| 10D300 | P268C | Adjustment of injector injection quantities Cylinder 1 |
| 10D400 | P268F | Adjustment of injector injection quantities Cylinder 4 |
| 10D500 | P268D | Adjustment of injector injection quantities Cylinder 2 |
| 10D600 | P2690 | Adjustment of injector injection quantities Cylinder 5 |
| 10D700 | P268E | Adjustment of injector injection quantities Cylinder 3 |
| 10D800 | P2691 | Adjustment of injector injection quantities Cylinder 6 |
| 10D900 | - | The coolant temperature is below the coolant thermostat specified temperature. |
| 10DA00 | - | Component B11/4 (Coolant temperature sensor) has a plausibility error. |
| 10DB00 | - | The dynamic test of component B11/4 (Coolant temperature sensor) was not successful. |
| 10DC00 | P0201 | Component Y76/1 (Cylinder 1 fuel injector) has Open circuit. |
| 10DD00 | P0204 | Component Y76/4 (Fuel injector cylinder 4) has Open circuit. |
| 10DE00 | P0202 | Component Y76/2 (Cylinder 2 fuel injector) has Open circuit. |
| 10DF00 | P0205 | Component Y76/5 (Fuel injector cylinder 5) has Open circuit. |
| 10E000 | P0203 | Component Y76/3 (Cylinder 3 fuel injector) has Open circuit. |
| 10E100 | P0206 | Component Y76/6 (Fuel injector cylinder 6) has Open circuit. |
| 10E200 | P0301 | The number of combustion misfires at cylinder 1 is too high. |
| 10E300 | P0304 | The number of combustion misfires at cylinder 4 is too high. |
| 10E400 | P0302 | The number of combustion misfires at cylinder 2 is too high. |
| 10E500 | P0305 | The number of combustion misfires at cylinder 5 is too high. |
| 10E600 | P0303 | The number of combustion misfires at cylinder 3 is too high. |
| 10E700 | P0306 | The number of combustion misfires at cylinder 6 is too high. |
| 10E800 | P0300 | The number of combustion misfires is too high at several cylinders. |
| 10E900 | P0607 | Control module has an internal error. |
| 10EA00 | P0607 | Control module has an internal error. |
| 10EB00 | P0607 | Control module has an internal error. |
| 10EC00 | P0607 | Control module has an internal error. |
| 10ED00 | P0607 | Control module has an internal error. |
| 10EE00 | P0607 | Control module has an internal error. |
| 10EF00 | - | Component B16/14 (Exhaust gas recirculation temperature sensor) has a plausibility error. |
| 10F100 | P0088 | The maximum rail pressure was exceeded. |
| 10F200 | P0088 | Value is below negative deviation. |
| 10F300 | P0088 | Value is below negative deviation. |
| 10F400 | P0088 | The maximum rail pressure was exceeded. |
| 10F500 | P0088 | The maximum rail pressure was exceeded. |
| 10F600 | - | Quantity correction for idle speed control for cylinder not within permissible tolerance |
| 10F700 | - | The number of combustion misfires at cylinder 1 is too high. |
| 10F800 | - | The number of combustion misfires at cylinder 4 is too high. |
| 10F900 | - | The number of combustion misfires at cylinder 2 is too high. |
| 10FA00 | - | The number of combustion misfires at cylinder 5 is too high. |
| 10FB00 | - | The number of combustion misfires at cylinder 3 is too high. |
| 10FC00 | P244C | This function is not available at present. |
| 10FD00 | P244D | This function is not available at present. |
| 10FE00 | P2458 | This function is not available at present. |
| 10FF00 | P244C | A fault was detected during regeneration of the diesel particulate filter. |
| 110000 | P244D | A fault was detected during regeneration of the diesel particulate filter. |
| 110100 | P2458 | Control module has an internal error. |
| 110200 | P0611 | There is an internal control unit fault in the digital/digital converter. |
| 110300 | P0611 | There is an internal control unit fault in the digital/digital converter. |
| 110600 | P0606 | The number of injections is limited because the fill level is too high. |
| 110700 | P0606 | The number of injections is limited because the injection quantity is too low. |
| 110800 | - | The number of injections is limited because the software is incorrect. |
| 110F00 | P060A | Control module has an internal error. |
| 111000 | P229E | The supply voltage of component NOx sensor downstream of SCR catalytic converter is too low (undervoltage). |
| 111200 | P2200 | The supply voltage of component NOx sensor upstream of SCR catalytic converter is too low (undervoltage). |
| 111300 | P0607 | Control module has an internal error. |
| 111400 | P2002 | Efficiency Diesel particulate filter |
| 111500 | P2459 | The soot content of the diesel particulate filter is implausible. |
| 111600 | P2458 | Regeneration of the diesel particulate filter was aborted. |
| 111700 | P2BA9 | Excessive nitrogen oxide emission due to low quality AdBlue |
| 111800 | P22A1 | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 111900 | P22A0 | Component NOx sensor downstream of SCR catalytic converter has a plausibility error. |
| 111A00 | P2203 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 111B00 | P2202 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 113200 | P014E | Component G3/1 (Oxygen sensor downstream of catalytic converter) reacts too slowly. |
| 113600 | P2234 | The output for the heater of oxygen sensor 2 (cylinder bank 1) has an electrical fault or open circuit. |
| 113A00 | P0052 | Oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| 113E00 | P0051 | Oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| 114600 | P0050 | The signal of oxygen sensor 2 (cylinder bank 1) does not change. |
| 114A00 | - | G3/1 (Oxygen sensor downstream of catalytic converter) The calibration value is too high. |
| 114E00 | P2630 | G3/1 (Oxygen sensor downstream of catalytic converter) The calibration value is too low. |
| 115200 | P0152 | The signal from component G3/1 (Oxygen sensor downstream of catalytic converter) is implausible. |
| 115600 | P0151 | The signal from component G3/1 (Oxygen sensor downstream of catalytic converter) is implausible. |
| 116200 | P0059 | G3/1 (Oxygen sensor downstream of catalytic converter) The calibration value is too high. |
| 116600 | P0059 | G3/1 (Oxygen sensor downstream of catalytic converter) The calibration value is too low. |
| 116A00 | P1999 | An internal component of the oxygen sensor has insufficient supply voltage. |
| 116E00 | P0607 | Component 'G3/1 (Oxygen sensor downstream of catalytic converter)' has an internal fault. |
| 117200 | P0150 | The pump current connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| 117600 | P0155 | The oxygen sensor heater has overtemperature. |
| 117A00 | P0155 | The temperature at component G3/1 (Oxygen sensor downstream of catalytic converter) is too low. |
| 118000 | P068A | Relay N10/1kC (Circuit 87 relay, engine) of component N10/1 (Front SAM control unit with fuse and relay module) switches off too early. |
| 118100 | P068B | Relay N10/1kC (Circuit 87 relay, engine) of component N10/1 (Front SAM control unit with fuse and relay module) switches off too late. |
| 118200 | P0001 | Component Y94 (Quantity control valve) has Open circuit. |
| 118300 | P0004 | Component Y94 (Quantity control valve) has Short circuit to positive. |
| 118400 | P0003 | Component Y94 (Quantity control valve) has Short circuit to ground. |
| 118500 | P0004 | There is an internal fault in component Y94 (Quantity control valve). |
| 118600 | P0003 | There is an internal fault in component Y94 (Quantity control valve). |
| 118800 | - | The signal from component Atmospheric pressure sensor is implausible. |
| 118A00 | - | Plausibility error due to defective exhaust gas pressure lines between diesel particulate filter and differential pressure sensor |
| 118B00 | - | Component B28/5 (Pressure sensor downstream of air filter) has a plausibility error. |
| 118D00 | - | Component B28/8 (Differential pressure sensor (DPF)) has a plausibility error. |
| 119100 | - | Component B19/9 (Temperature sensor upstream of diesel particulate filter) has a plausibility error. |
| 119400 | - | The oil level of the combustion engine is implausible. |
| 119A00 | - | The upper limit value of component B1 (Oil temperature sensor) has been reached. |
| 119B00 | - | Component B1 (Oil temperature sensor) has a plausibility error. |
| 119F00 | P0299 | The positive control deviation during boost pressure control is too high. |
| 11A000 | P0234 | The negative control deviation during boost pressure control is too high. |
| 11A100 | P0090 | Component Y74 (Pressure control valve) has Open circuit. |
| 11A200 | P0092 | Component Y74 (Pressure control valve) has Short circuit to positive. |
| 11A300 | P0091 | Component Y74 (Pressure control valve) has Short circuit to ground. |
| 11A400 | P0092 | The lower limit value of component Y74 (Pressure control valve) was dropped below/not reached. |
| 11A500 | P0091 | The upper limit value of component Y74 (Pressure control valve) has been exceeded. |
| 11A700 | P2463 | The fill level of the diesel particulate filter is too high. |
| 11A800 | P244B | The pressure differential in the diesel particulate filter is too high. |
| 11AA00 | P242F | The ash content of the diesel particulate filter is implausible. |
| 11AB00 | P2458 | Regeneration of the diesel particulate filter is permanently active. |
| 11AC00 | P1999 | The air mass in the diesel particulate filter is too high. |
| 11AD00 | P1999 | The air mass in the diesel particulate filter is too low. |
| 11B100 | P0627 | Component M3 (Fuel pump) has Open circuit. |
| 11B200 | P0629 | Component M3 (Fuel pump) has Short circuit to positive. |
| 11B300 | P0628 | Component M3 (Fuel pump) has Short circuit to ground. |
| 11B400 | P0602 | The control unit reports a plausibility error during quantity correction. |
| 11B500 | P0088 | Component Y74 (Pressure control valve) has a plausibility error. |
| 11B600 | P0087 | The minimum rail pressure was dropped below/not reached. |
| 11B700 | P0088 | The maximum rail pressure was exceeded. |
| 11B800 | P0087 | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 11B900 | P0087 | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 11BA00 | P0088 | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 11BB00 | P0087 | The rail pressure is too low during regulation via the quantity control valve. |
| 11BC00 | P0088 | The rail pressure is too high during regulation via the quantity control valve. |
| 11BD00 | P0087 | The control deviation during rail pressure regulation via the pressure regulator valve is too high. |
| 11BE00 | P0087 | The control deviation during rail pressure regulation via the pressure regulator valve is too high. |
| 11BF00 | P0088 | The control deviation during rail pressure regulation via the pressure regulator valve (in closed state) is too high. |
| 11C000 | P0087 | The rail pressure is too low during regulation via the pressure regulator valve. |
| 11C100 | P0088 | The rail pressure is too high during regulation via the pressure regulator valve. |
| 11C300 | P0191 | The upper limit value of component B4/6 (Rail pressure sensor) has been exceeded. |
| 11C400 | P0191 | The lower limit value of component B4/6 (Rail pressure sensor) was dropped below/not reached. |
| 11C500 | P0193 | The signal voltage of component B4/6 (Rail pressure sensor) is too high. |
| 11C600 | P0192 | The signal voltage of component B4/6 (Rail pressure sensor) is too low. |
| 11D000 | - | The signal voltage of component B28/5 (Pressure sensor downstream of air filter) is too high. |
| 11D100 | - | The signal voltage of component B28/8 (Differential pressure sensor (DPF)) is too high. |
| 11D400 | - | The signal voltage of the internal temperature sensor of the control unit is too high. |
| 11D500 | P042D | The signal voltage of component B19 (TWC temperature sensor) is too high. |
| 11D700 | - | The upper limit value of component B19/9 (Temperature sensor upstream of diesel particulate filter) has been exceeded. |
| 11D900 | - | The lower limit value of component B28/5 (Pressure sensor downstream of air filter) was dropped below/not reached. |
| 11DA00 | - | The lower limit value of component B28/8 (Differential pressure sensor (DPF)) was dropped below/not reached. |
| 11DD00 | - | The signal voltage of the internal temperature sensor of the control unit is too low. |
| 11DE00 | P042C | The signal voltage of component B19 (TWC temperature sensor) is too low. |
| 11E000 | - | The lower limit value of component B19/9 (Temperature sensor upstream of diesel particulate filter) was dropped below/not reached. |
| 11E600 | P0607 | An internal control unit reset was performed. |
| 11E700 | P0607 | An internal control unit reset was performed. |
| 11E900 | P0512 | Start attempt without starter actuation |
| 11EA00 | P0615 | Starter control has open circuit. |
| 11EB00 | P0617 | Starter control has short circuit to positive. |
| 11EC00 | P0616 | Starter control has short circuit to ground. |
| 11EF00 | - | The upper limit value of component B2/7b1 (Right intake air temperature sensor) has been exceeded. |
| 11F000 | - | The upper limit value of component B2/6b1 (Left intake air temperature sensor) has been exceeded. |
| 11F100 | - | The lower limit value of component B2/7b1 (Right intake air temperature sensor) was dropped below/not reached. |
| 11F200 | - | The lower limit value of component B2/6b1 (Left intake air temperature sensor) was dropped below/not reached. |
| 11F300 | - | The signal voltage of component B2/7b1 (Right intake air temperature sensor) is too high. |
| 11F400 | - | The signal voltage of component B2/6b1 (Left intake air temperature sensor) is too high. |
| 11F500 | - | The signal voltage of component B2/7b1 (Right intake air temperature sensor) is too low. |
| 11F600 | - | The signal voltage of component B2/6b1 (Left intake air temperature sensor) is too low. |
| 11F700 | - | The upper limit value of component B2/6b1 (Left intake air temperature sensor) has been exceeded. |
| 11F800 | - | The upper limit value of component B2/7b1 (Right intake air temperature sensor) has been exceeded. |
| 11F900 | - | The upper limit value of component B2/6b1 (Left intake air temperature sensor) has been exceeded. |
| 11FA00 | - | The upper limit value of component B2/7b1 (Right intake air temperature sensor) has been exceeded. |
| 11FB00 | - | The signal voltage of component B17/8 (Charge air temperature sensor) is too high. |
| 11FC00 | - | The signal voltage of component B17/8 (Charge air temperature sensor) is too low. |
| 120300 | P0638 | The limit value of component M16/6 (Throttle valve actuator) is exceeded due to offset drift. |
| 120400 | P2100 | Component M16/6 (Throttle valve actuator) has Open circuit. |
| 120600 | P2103 | Component M16/6 (Throttle valve actuator) has Short circuit to positive. |
| 120700 | P2102 | Component M16/6 (Throttle valve actuator) has Short circuit to ground. |
| 120800 | P0228 | The signal voltage of component M16/6 (Throttle valve actuator) is too high. |
| 120900 | P0227 | The signal voltage of component M16/6 (Throttle valve actuator) is too low. |
| 120A00 | P0638 | The limit value of component M16/6 (Throttle valve actuator) is exceeded due to offset drift. |
| 120B00 | P0045 | Component Y77/1 (Charge pressure positioner) has Open circuit. |
| 120C00 | P0048 | Component Y77/1 (Charge pressure positioner) has Short circuit to positive. |
| 120D00 | P0047 | Component Y77/1 (Charge pressure positioner) has Short circuit to ground. |
| 120E00 | P2565 | The signal voltage of component Y77/1 (Boost pressure regulator) is too high. |
| 120F00 | P2564 | The signal voltage of component Y77/1 (Boost pressure regulator) is too low. |
| 121000 | P060A | The plausibility check for the torque request from control unit A89 (DISTRONIC electric controller unit) was not performed. |
| 121100 | P060A | The plausibility check for the torque request from control unit N30/4 (Electronic Stability Program control unit) was not performed. |
| 121200 | P060A | The plausibility check for the torque request from control unit Transmission control was not performed. |
| 121300 | P2008 | Component M55 (Intake port shutoff actuator motor) has Open circuit. |
| 121400 | P2010 | Component M55 (Intake port shutoff actuator motor) has Short circuit to positive. |
| 121500 | P2009 | Component M55 (Intake port shutoff actuator motor) has Short circuit to ground. |
| 122300 | P0087 | The minimum rail pressure was dropped below/not reached. |
| 122400 | P0611 | The upper limit value for injector voltage has been exceeded. |
| 122500 | P0611 | The lower limit value for injector voltage has been dropped below. |
| 122C00 | P1999 | Component Y76/1 (Cylinder 1 fuel injector) is faulty. |
| 122D00 | P1999 | Component Y76/4 (Fuel injector cylinder 4) is faulty. |
| 122E00 | P1999 | Component Y76/2 (Cylinder 2 fuel injector) is faulty. |
| 122F00 | P1999 | Component Y76/5 (Fuel injector cylinder 5) is faulty. |
| 123000 | P1999 | Component Y76/3 (Cylinder 3 fuel injector) is faulty. |
| 123100 | P1999 | Component Y76/6 (Fuel injector cylinder 6) is faulty. |
| 123900 | P0299 | Charge pressure is too low. |
| 123A00 | P0234 | The negative control deviation during boost pressure control is too high. |
| 123B00 | - | A fault was detected during regeneration of the diesel particulate filter. |
| 123C00 | U0426 | A fault occurred during signal transmission from control unit N3/9 (CDI control unit) to control unit N73 (Electronic ignition lock control unit). |
| 123D00 | U0426 | There is an internal fault in system 'Immobilizer'. |
| 123E00 | U0426 | The value for authentication in system 'Immobilizer' is invalid. |
| 123F00 | P0633 | A locked key was detected by system 'Immobilizer'. |
| 124600 | P0643 | The supply voltage to the sensors is outside the valid range. |
| 124700 | P0653 | The supply voltage to the sensors is outside the valid range. |
| 124800 | P0699 | The supply voltage to the sensors is outside the valid range. |
| 124F00 | P0404 | Component Y27/9 (Left EGR positioner) is faulty. |
| 125000 | P0404 | Component Y27/9 (Left EGR positioner) is faulty. |
| 125C00 | P0299 | The positive control deviation during boost pressure control is too high. |
| 125E00 | P0234 | The negative control deviation during boost pressure control is too high. |
| 126000 | - | The output of radiator shutter 1 has an electrical fault. |
| 126100 | - | The output of radiator shutter 1 has a short circuit to positive. |
| 126200 | - | The output of radiator shutter 1 has a short circuit to ground. |
| 126300 | - | The output of radiator shutter 1 has a malfunction. |
| 126400 | - | The output of radiator shutter 1 has a malfunction. |
| 126500 | P02E0 | The output of radiator shutter 1 has an electrical fault. |
| 126600 | P02E3 | The output of radiator shutter 1 has a short circuit to positive. |
| 126700 | P02E2 | The output of radiator shutter 1 has a short circuit to ground. |
| 126800 | P0046 | Component Y77/1 (Charge pressure positioner) is faulty. |
| 126900 | P0046 | Component Y77/1 (Charge pressure positioner) is faulty. |
| 126A00 | P200A | Component M55 (Intake port shutoff actuator motor) is faulty. |
| 126B00 | P200A | Component M55 (Intake port shutoff actuator motor) is faulty. |
| 126C00 | - | The number of injections is limited due to the engine running time. |
| 126D00 | P268C | The values for injector injection quantity adjustment (cylinder 1) are faulty. |
| 126E00 | P268F | The values for injector injection quantity adjustment (cylinder 4) are faulty. |
| 126F00 | P268D | The values for injector injection quantity adjustment (cylinder 2) are faulty. |
| 127000 | P2690 | The values for injector injection quantity adjustment (cylinder 5) are faulty. |
| 127100 | P268E | The values for injector injection quantity adjustment (cylinder 3) are faulty. |
| 127200 | P2691 | The values for injector injection quantity adjustment (cylinder 6) are faulty. |
| 127900 | P0611 | The switch for selecting the injector bank in the control unit has a short circuit (injector bank 1). |
| 127A00 | P0611 | The switch for selecting the injector bank in the control unit has a short circuit (injector bank 2). |
| 128D00 | P0219 | The engine speed is too high. |
| 129200 | P1999 | The soot content of the diesel particulate filter is implausible. |
| 129300 | P1999 | The soot content of the diesel particulate filter is implausible. |
| 129400 | P2463 | The soot content of the diesel particulate filter is implausible. |
| 129700 | P2002 | The diesel particulate filter is defective. |
| 129A00 | P0341 | The position of the camshaft is implausible compared with the position of the crankshaft. |
| 12BC00 | P2002 | Component B28/8 (Differential pressure sensor (DPF)) has a plausibility error. |
| 12BD00 | P0087 | The control deviation during rail pressure regulation via the quantity control valve is too high. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 12BE00 | P0087 | The control deviation during rail pressure regulation via the quantity control valve is too high. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 12C000 | P042B | The temperature of component 'B19/19 (Temperature sensor upstream of diesel particulate filter)' is outside the valid range. |
| 12C100 | P042B | The temperature of component 'B19/19 (Temperature sensor upstream of diesel particulate filter)' is outside the valid range. |
| 12C300 | P2080 | The difference between the measured temperature and the calculated temperature of component B19 (Catalytic converter temperature sensor) is too great. |
| 12C400 | P0426 | The difference between the measured temperature and the calculated temperature of component B19/9 (Temperature sensor upstream of diesel particulate filter) is too great. |
| 12C500 | P042B | The temperature of component 'B19/19 (Temperature sensor upstream of diesel particulate filter)' is outside the valid range. |
| 12CA00 | P1011 | The energy consumption of the fuel injector of cylinder 1 has exceeded the upper limit value. |
| 12CB00 | P1014 | The energy consumption of the fuel injector of cylinder 4 has exceeded the upper limit value. |
| 12CC00 | P1012 | The energy consumption of the fuel injector of cylinder 2 has exceeded the upper limit value. |
| 12CD00 | P1015 | The energy consumption of the fuel injector of cylinder 5 has exceeded the upper limit value. |
| 12CE00 | P1013 | The energy consumption of the fuel injector of cylinder 3 has exceeded the upper limit value. |
| 12CF00 | - | The energy consumption of the fuel injector of cylinder 6 has exceeded the upper limit value. |
| 12D000 | P1999 | The energy consumption of the fuel injector of cylinder 1 has dropped below the lower limit value. |
| 12D100 | P1999 | The energy consumption of the fuel injector of cylinder 4 has dropped below the lower limit value. |
| 12D200 | P1999 | The energy consumption of the fuel injector of cylinder 2 has dropped below the lower limit value. |
| 12D300 | P1999 | The energy consumption of the fuel injector of cylinder 5 has dropped below the lower limit value. |
| 12D400 | P1999 | The energy consumption of the fuel injector of cylinder 3 has dropped below the lower limit value. |
| 12D500 | P1999 | The energy consumption of the fuel injector of cylinder 6 has dropped below the lower limit value. |
| 12D600 | - | The energy consumption of the fuel injector of cylinder 1 is implausible. |
| 12D700 | P1999 | The energy consumption of the fuel injector of cylinder 4 is implausible. |
| 12D800 | P1999 | The energy consumption of the fuel injector of cylinder 2 is implausible. |
| 12D900 | P1999 | The energy consumption of the fuel injector of cylinder 5 is implausible. |
| 12DA00 | P1999 | The energy consumption of the fuel injector of cylinder 3 is implausible. |
| 12DB00 | P1999 | The energy consumption of the fuel injector of cylinder 6 is implausible. |
| 12E200 | P1146 | Control module has an internal error. |
| 12E300 | P1149 | Control module has an internal error. |
| 12E500 | P2148 | Injector bank 1 has a short circuit. |
| 12E600 | P2151 | Injector bank 2 has a short circuit. |
| 12ED00 | P0262 | The fuel injector of cylinder 1 has a short circuit. |
| 12EE00 | P0271 | The fuel injector of cylinder 4 has a short circuit. |
| 12EF00 | P0265 | The fuel injector of cylinder 2 has a short circuit. |
| 12F000 | P0274 | The fuel injector of cylinder 5 has a short circuit. |
| 12F100 | P0268 | The fuel injector of cylinder 3 has a short circuit. |
| 12F200 | P0277 | The fuel injector of cylinder 6 has a short circuit. |
| 12F300 | P0261 | The fuel injector of cylinder 1 has a short circuit between positive and ground. |
| 12F400 | P0270 | The fuel injector of cylinder 4 has a short circuit between positive and ground. |
| 12F500 | P0264 | The fuel injector of cylinder 2 has a short circuit between positive and ground. |
| 12F600 | P0273 | The fuel injector of cylinder 5 has a short circuit between positive and ground. |
| 12F700 | P0267 | The fuel injector of cylinder 3 has a short circuit between positive and ground. |
| 12F800 | P0276 | The fuel injector of cylinder 6 has a short circuit between positive and ground. |
| 12FB00 | P0152 | Oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| 12FF00 | P0151 | Oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| 130300 | P060B | Control module has an internal error. |
| 130400 | P060B | Control module has an internal error. |
| 130500 | P061C | Control module has an internal error. |
| 130600 | P060A | Control module has an internal error. |
| 130800 | P060A | Control module has an internal error. |
| 130900 | P060A | Control module has an internal error. |
| 130A00 | P060A | Control module has an internal error. |
| 130B00 | P061B | Control module has an internal error. |
| 130C00 | P0607 | Control module has an internal error. |
| 130D00 | P0607 | Control module has an internal error. |
| 130E00 | P0607 | Control module has an internal error. |
| 130F00 | P228F | The learned value of the pressure regulator valve has exceeded the upper limit value. |
| 131000 | P228E | The learned value of the pressure regulator valve has dropped below the lower limit value. |
| 131100 | P0088 | The control deviation during rail pressure regulation is too high. |
| 131200 | P0088 | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 131300 | P0087 | The control deviation during rail pressure regulation is too high. |
| 131400 | P0088 | The control deviation during rail pressure regulation via the pressure regulator valve is too high. |
| 131500 | P0088 | The maximum rail pressure was exceeded. |
| 131700 | P0610 | Fault when reading the EEPROM |
| 131E00 | P0148 | Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 131F00 | P0088 | Component Y74 (Pressure control valve) has a plausibility error. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132000 | P0087 | The minimum rail pressure was dropped below/not reached. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132300 | P0087 | The rail pressure is too low during regulation via the quantity control valve. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132400 | P0087 | The control deviation during rail pressure regulation is too high. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132500 | P0087 | The control deviation during rail pressure regulation via the pressure regulator valve is too high. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132600 | P0087 | The minimum rail pressure was dropped below/not reached. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 132700 | - | The signal voltage of component 17B03: Temperature sensor, exhaust gas downstream of SCR catalytic converter is too high. |
| 132800 | - | The signal voltage of component B16/15 (Temperature sensor upstream of SCR catalytic converter) is too high. |
| 132C00 | - | The lower limit value of component B16/15 (Temperature sensor upstream of SCR catalytic converter) was dropped below/not reached. |
| 132D00 | - | The signal voltage of component 17B03: Temperature sensor, exhaust gas downstream of SCR catalytic converter is too high. |
| 132E00 | - | The signal voltage of component B16/15 (Temperature sensor upstream of SCR catalytic converter) is too low. |
| 133000 | P2201 | The upper limit value of component NOx sensor upstream of SCR catalytic converter has been reached. |
| 133100 | P2201 | The lower limit value of component NOx sensor upstream of SCR catalytic converter was dropped below/not reached. |
| 133200 | P2201 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 134800 | U029E | No CAN message received from component NOx sensor downstream of SCR catalytic converter. |
| 134900 | U029D | No CAN message received from component NOx sensor upstream of SCR catalytic converter. |
| 134A00 | P2201 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 134B00 | P2203 | The upper limit value of component NOx sensor upstream of SCR catalytic converter has been exceeded. |
| 134C00 | P2202 | The lower limit value of component NOx sensor upstream of SCR catalytic converter was dropped below/not reached. |
| 134D00 | P2203 | The upper limit value of component NOx sensor upstream of SCR catalytic converter has been exceeded. |
| 134E00 | P2202 | The lower limit value of component NOx sensor upstream of SCR catalytic converter was dropped below/not reached. |
| 134F00 | P2201 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 135100 | P2203 | Signal of component NOx sensor upstream of SCR catalytic converter is not within the valid range. |
| 135200 | P2202 | Signal of component NOx sensor upstream of SCR catalytic converter is not within the valid range. |
| 135300 | P2200 | Component NOx sensor upstream of SCR catalytic converter has an open circuit in the wiring. |
| 135400 | P2200 | Short circuit in component NOx sensor upstream of SCR catalytic converter |
| 135600 | - | The upper limit value of component B16/15 (Temperature sensor upstream of SCR catalytic converter) has been exceeded. |
| 135900 | - | The signal voltage of component 17B03: Temperature sensor, exhaust gas downstream of SCR catalytic converter is too high. |
| 139700 | - | This function is not yet supported by the control unit. |
| 13A800 | P244C | The exhaust gas temperature is too low. |
| 13A900 | P244D | The exhaust-gas temperature is too high. |
| 13AA00 | P06B2 | The supply voltage of control unit N3/9 (CDI control unit) is too high (overvoltage). |
| 13AB00 | P06B1 | The supply voltage of control unit N3/9 (CDI control unit) is too low (undervoltage). |
| 13AC00 | P053C | The output stage of the heater for the crankcase ventilation system has a short circuit to positive. |
| 13AD00 | P053B | The output stage of the heater for the crankcase ventilation system has a short circuit to ground. |
| 13AE00 | P053A | The heater for the crankcase ventilation system has a fault at the output stage. |
| 13AF00 | P2463 | The soot content of the diesel particulate filter is too high. |
| 13B400 | P062F | There is an internal control unit fault in the ROM memory. |
| 13B500 | P062F | There is an internal control unit fault in the ROM memory. |
| 13B600 | P062F | There is an internal control unit fault in the ROM memory. |
| 13B700 | P1999 | Manual regeneration must be deactivated. |
| 13B800 | P2280 | Soiling limit of air cleaner is reached. |
| 13B900 | P0087 | The control deviation during rail pressure regulation via the quantity control valve is too high. Rail pressure deviation due to air forming in the system when the fuel tank is run empty |
| 13BA00 | P0263 | Maximum actuation duration for zero quantity calibration for injector of cylinder 1 exceeded |
| 13BB00 | P0272 | Maximum actuation duration for zero quantity calibration for injector of cylinder 4 exceeded |
| 13BC00 | P0266 | Maximum actuation duration for zero quantity calibration for injector of cylinder 2 exceeded |
| 13BD00 | P0275 | Maximum actuation duration for zero quantity calibration for injector of cylinder 5 exceeded |
| 13BE00 | P0269 | Maximum actuation duration for zero quantity calibration for injector of cylinder 3 exceeded |
| 13BF00 | P0278 | Maximum actuation duration for zero quantity calibration for injector of cylinder 6 exceeded |
| 13C000 | P0263 | Minimum actuation duration for zero quantity calibration for injector of cylinder 1 not reached |
| 13C100 | P0272 | Minimum actuation duration for zero quantity calibration for injector of cylinder 4 not reached |
| 13C200 | P0266 | Minimum actuation duration for zero quantity calibration for injector of cylinder 2 not reached |
| 13C300 | P0275 | Minimum actuation duration for zero quantity calibration for injector of cylinder 5 not reached |
| 13C400 | P0269 | Minimum actuation duration for zero quantity calibration for injector of cylinder 3 not reached |
| 13C500 | P0278 | Minimum actuation duration for zero quantity calibration for injector of cylinder 6 not reached |
| 13C600 | - | Component N14/3 (Glow output stage) has excess temperature. |
| 13C700 | - | Component N14/3 (Glow output stage) has a malfunction. |
| 13C800 | - | The supply voltage of component N14/3 (Glow output stage) is too low (undervoltage). |
| 13C900 | P064C | There is an internal fault in component N14/3 (Glow output stage). |
| 13CA00 | P0671 | Component R9/1 (Cylinder 1 glow plug) has Open circuit. |
| 13CB00 | P0672 | Component R9/2 (Cylinder 2 glow plug) has Open circuit. |
| 13CC00 | P0673 | Component R9/3 (Cylinder 3 glow plug) has Open circuit. |
| 13CD00 | P0674 | Component R9/4 (Cylinder 4 glow plug) has Open circuit. |
| 13CE00 | P0675 | Component R9/5 (Glow plug cylinder 5) has Open circuit. |
| 13CF00 | P0676 | Component R9/6 (Cylinder 6 glow plug) has Open circuit. |
| 13D000 | P0677 | The output for the glow plug (cylinder 7) has an electrical fault or an open circuit. |
| 13D100 | P0678 | The output for the glow plug (cylinder 8) has an electrical fault or an open circuit. |
| 13D200 | P06B9 | The resistance of the glow plug at cylinder R9/1 (Cylinder 1 glow plug) is outside the permissible range. |
| 13D300 | P06BA | The resistance of the glow plug at cylinder R9/2 (Cylinder 2 glow plug) is outside the permissible range. |
| 13D400 | P06BB | The resistance of the glow plug at cylinder R9/3 (Cylinder 3 glow plug) is outside the permissible range. |
| 13D500 | P06BC | The resistance of the glow plug at cylinder R9/4 (Cylinder 4 glow plug) is outside the permissible range. |
| 13D600 | P06BD | The resistance of the glow plug at cylinder R9/5 (Glow plug cylinder 5) is outside the permissible range. |
| 13D700 | P06BE | The resistance of the glow plug at cylinder R9/6 (Cylinder 6 glow plug) is outside the permissible range. |
| 13D800 | P06BF | The output for the glow plug (cylinder 7) has an electrical fault or an open circuit. |
| 13D900 | P06C0 | The output for the glow plug (cylinder 8) has an electrical fault or an open circuit. |
| 13DA00 | P066A | Component R9/1 (Cylinder 1 glow plug) has Short circuit to ground. |
| 13DB00 | P066C | Component R9/2 (Cylinder 2 glow plug) has Short circuit to ground. |
| 13DC00 | P066E | Component R9/3 (Cylinder 3 glow plug) has Short circuit to ground. |
| 13DD00 | P067A | Component R9/4 (Cylinder 4 glow plug) has Short circuit to ground. |
| 13DE00 | P067C | Component R9/5 (Glow plug cylinder 5) has Short circuit to ground. |
| 13DF00 | P067E | Component R9/6 (Cylinder 6 glow plug) has Short circuit to ground. |
| 13E000 | P068C | The output for the glow plug (cylinder 7) has an electrical fault or an open circuit. |
| 13E100 | P068E | The output for the glow plug (cylinder 8) has an electrical fault or an open circuit. |
| 13E200 | - | The lower limit value of component B28/8 (Differential pressure sensor (DPF)) was dropped below/not reached. |
| 13E300 | P1999 | The energy consumption of the fuel injector of cylinder 7 is implausible. |
| 13E400 | P1999 | The energy consumption of the fuel injector of cylinder 8 is implausible. |
| 13E700 | P0263 | The OBD limit value for the injector voltage of cylinder 1 has been exceeded. |
| 13E800 | P0272 | The OBD limit value for the injector voltage of cylinder 4 has been exceeded. |
| 13E900 | P0266 | The OBD limit value for the injector voltage of cylinder 2 has been exceeded. |
| 13EA00 | P0275 | The OBD limit value for the injector voltage of cylinder 5 has been exceeded. |
| 13EB00 | P0269 | The OBD limit value for the injector voltage of cylinder 3 has been exceeded. |
| 13EC00 | P0278 | The OBD limit value for the injector voltage of cylinder 6 has been exceeded. |
| 13ED00 | P1999 | The energy consumption of the fuel injector of cylinder 7 has exceeded the upper limit value. |
| 13EE00 | - | The energy consumption of the fuel injector of cylinder 8 is implausible. |
| 13EF00 | - | The energy consumption of the fuel injector of cylinder 7 has dropped below the lower limit value. |
| 13F000 | - | The energy consumption of the fuel injector of cylinder 8 has dropped below the lower limit value. |
| 13F100 | P0263 | Continuous control deviation during discharge time of fuel injector of cylinder 1 |
| 13F200 | P0272 | Continuous control deviation during discharge time of fuel injector of cylinder 4 |
| 13F300 | P0266 | Continuous control deviation during discharge time of fuel injector of cylinder 2 |
| 13F400 | P0275 | Continuous control deviation during discharge time of fuel injector of cylinder 5 |
| 13F500 | P0269 | Continuous control deviation during discharge time of fuel injector of cylinder 3 |
| 13F600 | P0278 | Continuous control deviation during discharge time of fuel injector of cylinder 6 |
| 13F700 | P0263 | The OBD limit value for the injector voltage of cylinder 1 has been exceeded. |
| 13F800 | P0272 | The OBD limit value for the injector voltage of cylinder 4 has been exceeded. |
| 13F900 | P0266 | The OBD limit value for the injector voltage of cylinder 2 has been exceeded. |
| 13FA00 | P0275 | The OBD limit value for the injector voltage of cylinder 5 has been exceeded. |
| 13FB00 | P0269 | The OBD limit value for the injector voltage of cylinder 3 has been exceeded. |
| 13FC00 | P0278 | The OBD limit value for the injector voltage of cylinder 6 has been exceeded. |
| 13FD00 | P0261 | The fuel injector of cylinder 1 has a short circuit. |
| 13FE00 | P0270 | The fuel injector of cylinder 4 has a short circuit. |
| 13FF00 | P0264 | The fuel injector of cylinder 2 has a short circuit. |
| 140000 | P0273 | The fuel injector of cylinder 5 has a short circuit. |
| 140100 | P0267 | The fuel injector of cylinder 3 has a short circuit. |
| 140200 | P0276 | The fuel injector of cylinder 6 has a short circuit. |
| 140500 | P2197 | Component is not installed. |
| 140900 | P2197 | Component is not installed. |
| 140D00 | P2198 | Component is not installed. |
| 141100 | P2198 | Component is not installed. |
| 141600 | P1999 | Exhaust gas recirculation was shut off due to the malfunction of one of the hot film mass air flow sensors. |
| 141800 | P0607 | Control module has an internal error. |
| 141900 | P0607 | Control module has an internal error. |
| 141A00 | P0607 | Control module has an internal error. |
| 141B00 | P0607 | Control module has an internal error. |
| 141C00 | P0607 | Control module has an internal error. |
| 141D00 | P0607 | Control module has an internal error. |
| 141E00 | P0607 | Control module has an internal error. |
| 141F00 | P060D | Control module has an internal error. |
| 142000 | P060A | Control module has an internal error. |
| 142100 | P060A | Control module has an internal error. |
| 142200 | P060A | Control module has an internal error. |
| 142400 | P2197 | Component is not installed. |
| 142800 | P2198 | Component is not installed. |
| 142B00 | P242F | The ash content of the diesel particulate filter is too high. |
| 142C00 | P242F | The ash content of the diesel particulate filter has exceeded the warning threshold. |
| 142E00 | P0610 | Internal error: data record faulty |
| 142F00 | P0610 | Internal error: data record faulty |
| 143200 | B1C32 | A frontal impact was detected. |
| 143300 | U0551 | The check signal from control unit Airbag is implausible. |
| 143400 | P0560 | A shortcut was detected at pin 1 of circuit 87. |
| 143500 | P0563 | The voltage supply of circuit 87 has overvoltage. |
| 143600 | P0562 | The voltage supply of circuit 87 has undervoltage. |
| 143700 | P0560 | A shortcut was detected at pin 2 of circuit 87. |
| 143800 | P0563 | The voltage supply of circuit 87 has overvoltage. |
| 143900 | P0562 | The voltage supply of circuit 87 has undervoltage. |
| 143A00 | P0381 | Component A1e16 (Preglow indicator lamp) is defective. |
| 143C00 | P042B | The supply voltage of the component B19 (TWC temperature sensor) is implausible. |
| 143D00 | P042B | The supply voltage of the component B19 (TWC temperature sensor) is implausible. |
| 143E00 | P043B | The supply voltage of the component B19 (TWC temperature sensor) is implausible. |
| 143F00 | - | Component B19/9 (Temperature sensor upstream of diesel particulate filter) has an open circuit. |
| 144700 | P2118 | Component M16/6 (Throttle valve actuator) has a plausibility error. |
| 144800 | P2118 | Control module has an internal error. |
| 144900 | P0607 | Control module has an internal error. |
| 144A00 | P2103 | Control module has an internal error. |
| 144B00 | P2103 | Control module has an internal error. |
| 144C00 | P2102 | Control module has an internal error. |
| 144D00 | P2102 | Control module has an internal error. |
| 144E00 | P2118 | Control module has an internal error. |
| 144F00 | P2118 | Control module has an internal error. |
| 145000 | P2118 | Control module has an internal error. |
| 145100 | P0607 | The control unit is overheated. |
| 145200 | P113D | Component is not installed. |
| 145300 | P0611 | There is an internal control unit fault in the digital/digital converter. |
| 145400 | P0611 | There is an internal control unit fault in the digital/digital converter. |
| 145700 | P046A | One of the exhaust gas temperature sensors has overtemperature. |
| 145B00 | U0400 | Signal 'PremAir sensor' on CAN bus is not present or is faulty. |
| 145D00 | P0638 | Component M16/6 (Throttle valve actuator) has a plausibility error. |
| 145E00 | P0638 | The positive control deviation during throttle valve control is too high. |
| 145F00 | P0638 | The negative control deviation during throttle valve control is too high. |
| 146100 | P0171 | Control deviation is too large. |
| 146200 | P0172 | Control deviation is too large. |
| 146300 | P2681 | Component R48 (Two-disk thermostat heating element) has an open circuit. |
| 146400 | P2683 | Component R48 (Two-disk thermostat heating element) has a short circuit to positive. |
| 146500 | P2682 | Component R48 (Two-disk thermostat heating element) has a short circuit to ground. |
| 146600 | P2755 | Component M13/7 (Transmission oil cooler circulation pump) has an open circuit. |
| 146700 | P0607 | Component M13/7 (Transmission oil cooler circulation pump) has excess temperature. |
| 146800 | P2754 | Component M13/7 (Transmission oil cooler circulation pump) has a short circuit to positive. |
| 146900 | P2753 | Component M13/7 (Transmission oil cooler circulation pump) has a short circuit to ground. |
| 146A00 | P2600 | Component is not installed. |
| 146B00 | P2603 | Component is not installed. |
| 146C00 | P2602 | Component is not installed. |
| 146D00 | P229F | Plausibility error between signals of components NOx sensor upstream of SCR catalytic converter and NOx sensor downstream of SCR catalytic converter |
| 147200 | P229F | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 147300 | P229F | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 147400 | P22A1 | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 147500 | P22A0 | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 147600 | P229E | Component NOx sensor downstream of SCR catalytic converter has an open circuit in the wiring. |
| 147700 | P229E | Component NOx sensor downstream of SCR catalytic converter has a short circuit. |
| 147800 | P242F | The ash content of the diesel particulate filter is too high. |
| 147900 | P244B | The pressure differential in the diesel particulate filter is too high. |
| 147B00 | - | Component B16/14 (Exhaust gas recirculation temperature sensor) has a short circuit to positive. |
| 147C00 | - | Component B16/14 (Exhaust gas recirculation temperature sensor) has a short circuit to ground. |
| 147E00 | P2601 | This function is not available at present. |
| 147F00 | P2601 | This function is not available at present. |
| 148000 | P229F | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been reached. |
| 148100 | P229F | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 148200 | P229F | Component NOx sensor downstream of SCR catalytic converter has a plausibility error. |
| 148300 | P0089 | The number of permissible start attempts has been exceeded. |
| 148A00 | P2459 | The number of times regeneration of the diesel particulate filter was performed is too high. |
| 148B00 | P0404 | The negative control deviation of exhaust gas recirculation control is too high. |
| 148C00 | P0487 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 148D00 | P0488 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 148E00 | P0607 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 148F00 | P2142 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149000 | P2142 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149100 | P2141 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149200 | P2141 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149300 | P0488 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149400 | P0488 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149500 | P0488 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149600 | P0607 | Control module has an internal error. |
| 149700 | P0409 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149800 | P0409 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149900 | P0406 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149A00 | P0405 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 149C00 | P2201 | Component NOx sensor upstream of SCR catalytic converter is not operational. |
| 149D00 | P229F | Component NOx sensor downstream of SCR catalytic converter is not operational. |
| 14A000 | P049D | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 14A100 | P049D | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 14A300 | - | Component B17/8 (Charge air temperature sensor) has a plausibility error. |
| 14A600 | P0401 | The positive control deviation of exhaust gas recirculation control is too high. |
| 14A700 | P0402 | The negative control deviation of exhaust gas recirculation control is too high. |
| 14A900 | P0234 | The upper limit value of component B60 (Exhaust back pressure sensor) has been exceeded. |
| 14AB00 | P2080 | Component B19/11 (Temperature sensor upstream of turbocharger) has a plausibility error. |
| 14AC00 | P2080 | There is an internal fault in component B19/11 (Temperature sensor upstream of turbocharger). |
| 14AD00 | P052E | This function is not available at present. |
| 14AF00 | - | Component B5/1 (Charge pressure sensor) has a plausibility error. |
| 14B000 | P006D | The relative boost pressure exceeds the upper limit value. |
| 14B100 | P0101 | Component Hot film mass air flow sensor has a plausibility error. |
| 14B200 | P0101 | Component Hot film mass air flow sensor has a plausibility error. |
| 14B300 | P0404 | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 14B400 | P0404 | The control deviation of component Y27/9 (Left EGR positioner) is too high. |
| 14B500 | P2201 | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| 14B700 | P042F | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 14B800 | P042E | The control deviation of component Y27/9 (Left EGR positioner) is too high. |
| 14CF00 | P0404 | The positive control deviation of exhaust gas recirculation control is too high. |
| 14D500 | - | Water in engine oil |
| 14D600 | P2231 | The signal line of oxygen sensor 1 (cylinder bank 1) and the electric heater circuit have a short circuit to each other. |
| 14D700 | P0563 | The battery voltage is too high. |
| 14D800 | P0562 | Battery voltage is too low. |
| 14D900 | P2243 | The reference voltage connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| 14DA00 | P2247 | Component is not installed. |
| 14DB00 | P2237 | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| 14DC00 | P2240 | Component is not installed. |
| 14DD00 | P0130 | The signal return line connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| 14DE00 | P0150 | Component is not installed. |
| 14DF00 | P0032 | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| 14E000 | P0031 | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| 14E100 | P0135 | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| 14E200 | P0155 | Component is not installed. |
| 14E300 | P0030 | The output for the heater of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| 14E400 | P0132 | Oxygen sensor 1 (cylinder bank 1) has a malfunction. |
| 14E500 | P0131 | Oxygen sensor 1 (cylinder bank 1) has a malfunction. |
| 14E600 | P1999 | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 14E700 | P0132 | Oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| 14E800 | P0131 | Oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| 14E900 | P0135 | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| 14EA00 | P0135 | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| 14EB00 | P014C | Rich/lean switchover of oxygen sensor 1 (cylinder bank 1) too slow. |
| 14EE00 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 14EF00 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 14F000 | P2195 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Lean'. |
| 14F100 | P2195 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Lean'. |
| 14F200 | P2195 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Lean'. |
| 14F300 | P2196 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Rich'. |
| 14F400 | P2196 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Rich'. |
| 14F500 | P2196 | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Rich'. |
| 14F600 | P2A00 | Oxygen sensor 1 (cylinder bank 1) has a malfunction. |
| 14F700 | P2A03 | Component is not installed. |
| 14F800 | P2A00 | This function is not yet supported by the control unit. |
| 14F900 | P2A03 | Component is not installed. |
| 14FA00 | P0053 | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 14FB00 | P0053 | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 150000 | P0130 | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| 150100 | P0101 | The upper limit value of component HFM-SFI has been exceeded. |
| 150200 | P0101 | The upper limit value of component HFM-SFI has been exceeded. |
| 150300 | P0101 | The upper limit value of component HFM-SFI has been exceeded. |
| 150400 | P0607 | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| 150500 | P2413 | This function is not available at present. |
| 150800 | P22A1 | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 150900 | P22A0 | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 150A00 | P22A1 | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 150B00 | P22A0 | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 150C00 | - | There is an internal fault in component B19 (TWC temperature sensor). |
| 150D00 | - | Component B19 (TWC temperature sensor) has a short circuit to positive. |
| 150E00 | - | Component B19 (TWC temperature sensor) has a short circuit to ground. |
| 150F00 | - | This function is not available at present. |
| 151000 | U0515 | This function is not available at present. |
| 151100 | U0515 | This function is not available at present. |
| 151200 | U0515 | This function is not available at present. |
| 151300 | U0515 | This function is not available at present. |
| 151400 | U0515 | This function is not available at present. |
| 151500 | P0607 | Component Y85 (Exhaust gas recirculation cooler bypass switchover valve) has excess temperature. |
| 151600 | - | This function is not yet supported by the control unit. |
| 151700 | - | This function is not yet supported by the control unit. |
| 151800 | - | This function is not yet supported by the control unit. |
| 151C00 | P1999 | There is an internal fault in component B11/4 (Coolant temperature sensor). |
| 151D00 | - | This function is not yet supported by the control unit. |
| 151E00 | - | Component is not installed. |
| 151F00 | P0638 | The throttle valve is blocked due to ice. |
| 152000 | P0638 | The signal from component M16/6 (Throttle valve actuator) is implausible. |
| 152100 | P0638 | The signal from component M16/6 (Throttle valve actuator) is implausible. |
| 152200 | P049D | The signal from component Y27/9 (Exhaust gas recirculation positioner) is implausible. |
| 152300 | P0341 | Component 'B6/1 (Camshaft Hall sensor)' has an internal fault. |
| 152400 | U0426 | The start enable signal was withdrawn due to a timeout. |
| 152500 | P0607 | Control module has an internal error. |
| 152600 | P0607 | Control module has an internal error. |
| 152700 | P0607 | Control module has an internal error. |
| 152800 | P0607 | Control module has an internal error. |
| 152900 | P0607 | Control module has an internal error. |
| 152A00 | - | The signal from component M4/7 (Engine and AC electric suction fan with integrated control) is implausible. |
| 152B00 | - | The signal from component M4/7 (Engine and AC electric suction fan with integrated control) is implausible. |
| 152C00 | - | The signal from component M4/7 (Engine and AC electric suction fan with integrated control) is implausible. |
| 152D00 | - | The signal from component M4/7 (Engine and AC electric suction fan with integrated control) is implausible. |
| 153000 | P204F | The metered quantity of AdBlue is too low. |
| 153100 | P2BA8 | The NOx concentration downstream of the SCR catalytic converter is too high. |
| 153500 | P2201 | Component NOx sensor upstream of SCR catalytic converter reacts too slowly. |
| 153600 | P2201 | Component 'NOx sensor upstream of SCR catalytic converter' has an internal fault. |
| 153700 | P229F | The limit value of component NOx sensor downstream of SCR catalytic converter is exceeded due to offset drift. |
| 153800 | P229F | The signal from component NOx sensor downstream of SCR catalytic converter is faulty. |
| 153B00 | P229F | The signal from component NOx sensor downstream of SCR catalytic converter is faulty. |
| 153C00 | P229F | The signal from component NOx sensor downstream of SCR catalytic converter is faulty. |
| 154000 | P0607 | Control module has an internal error. |
| 154300 | - | This function is not yet supported by the control unit. |
| 154400 | - | This function is not yet supported by the control unit. |
| 154500 | - | This function is not yet supported by the control unit. |
| 154700 | U040A | The request for fan output is implausible. |
| 154800 | P0127 | Inspect intercooler. |
| 154900 | P2425 | Component 'Y85 (Exhaust gas recirculation cooler bypass switchover valve)' has an internal fault. |
| 154B00 | P1999 | This function is not yet supported by the control unit. |
| 154C00 | P1999 | This function is not yet supported by the control unit. |
| 154D00 | - | This function is not yet supported by the control unit. |
| 154E00 | - | This function is not yet supported by the control unit. |
| 154F00 | - | There is an internal fault in component G3/2 (O2 sensor upstream of KAT). |
| 155000 | - | This function is not yet supported by the control unit. |
| 155100 | - | This function is not yet supported by the control unit. |
| 155200 | - | This function is not yet supported by the control unit. |
| 155300 | - | This function is not yet supported by the control unit. |
| 155400 | P2000 | This function is not yet supported by the control unit. |
| 155500 | P061B | Control module has an internal error. |
| 155600 | - | This function is not yet supported by the control unit. |
| 155700 | P0A1E | Engine start is not possible because the combustion engine is blocked. |
| 155A00 | P2201 | Offset of component NOx sensor upstream of SCR catalytic converter: The calibration value is too high. |
| 155B00 | P2201 | Offset of component NOx sensor upstream of SCR catalytic converter: The calibration value is too low. |
| 155C00 | P2610 | The engine off time is implausible. |
| 155D00 | P0404 | Exhaust gas recirculation positioner --- Temporary fault |
| 155E00 | - | The difference between the measured temperature and the calculated temperature of component B19/9 (Temperature sensor upstream of diesel particulate filter) is too great. |
| 155F00 | P0401 | The positive control deviation of exhaust gas recirculation control is too high. |
| 156000 | P0402 | The negative control deviation of exhaust gas recirculation control is too high. |
| 156100 | P0263 | This function is not yet supported by the control unit. |
| 156200 | P0272 | This function is not yet supported by the control unit. |
| 156300 | P0266 | This function is not yet supported by the control unit. |
| 156400 | P0275 | This function is not yet supported by the control unit. |
| 156500 | P0269 | This function is not yet supported by the control unit. |
| 156600 | P0278 | This function is not yet supported by the control unit. |
| 156700 | - | This function is not yet supported by the control unit. |
| 156800 | - | The signal from component B28/8 (Pressure differential sensor (DPF)) is implausible. |
| 156900 | - | The signal voltage of component B28/16 (DPF differential pressure sensor for OBD) is too high. |
| 156A00 | - | The signal voltage of component B28/16 (DPF differential pressure sensor for OBD) is too low. |
| 156B00 | - | The lower limit value of component B28/16 (DPF differential pressure sensor for OBD) was dropped below/not reached. |
| 156C00 | - | This function is not yet supported by the control unit. |
| 156D00 | - | Component 'B19 (TWC temperature sensor)' has an internal fault. |
| 156E00 | - | Component 'B19 (TWC temperature sensor)' has an internal fault. |
| 156F00 | P0607 | Component 'Y77/1 (Charge pressure positioner)' has an internal fault. |
| 157000 | - | Component 'High-pressure pump' has an internal fault. |
| 157100 | - | Component 'High-pressure pump' has an internal fault. |
| 157200 | - | Component 'High-pressure pump' has an internal fault. |
| 157300 | - | Component 'High-pressure pump' has an internal fault. |
| 157400 | - | Component B28/16 (DPF differential pressure sensor for OBD) has a plausibility error. |
| 157500 | - | Component B28/16 (DPF differential pressure sensor for OBD) has a plausibility error. |
| 157600 | P2413 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 157700 | P2413 | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 157800 | P0483 | Electric fan has a malfunction. |
| 157900 | P0399 | The combustion chamber pressure sensor (cylinder 1) has a malfunction. |
| 157A00 | P0396 | The combustion chamber pressure sensor (cylinder 1) has a malfunction. |
| 157B00 | P0398 | The combustion chamber pressure sensor (cylinder 1) has a short circuit to positive. |
| 157C00 | P0397 | The combustion chamber pressure sensor (cylinder 1) has a short circuit to ground. |
| 157D00 | P03A3 | The combustion chamber pressure sensor (cylinder 2) has a malfunction. |
| 157E00 | P03A0 | The combustion chamber pressure sensor (cylinder 2) has a malfunction. |
| 157F00 | P03A2 | The combustion chamber pressure sensor (cylinder 2) has a short circuit to positive. |
| 158000 | P03A1 | The combustion chamber pressure sensor (cylinder 2) has a short circuit to ground. |
| 158100 | P03AD | The combustion chamber pressure sensor (cylinder 3) has a malfunction. |
| 158200 | P03AA | The combustion chamber pressure sensor (cylinder 3) has a malfunction. |
| 158300 | P03AC | The combustion chamber pressure sensor (cylinder 3) has a short circuit to positive. |
| 158400 | P03AB | The combustion chamber pressure sensor (cylinder 3) has a short circuit to ground. |
| 158500 | P03B7 | The combustion chamber pressure sensor (cylinder 4) has a malfunction. |
| 158600 | P03B4 | The combustion chamber pressure sensor (cylinder 4) has a malfunction. |
| 158700 | P03B6 | The combustion chamber pressure sensor (cylinder 4) has a short circuit to positive. |
| 158800 | P03B5 | The combustion chamber pressure sensor (cylinder 4) has a short circuit to ground. |
| 158900 | P03C1 | The combustion chamber pressure sensor (cylinder 5) has a malfunction. |
| 158A00 | P03BE | The combustion chamber pressure sensor (cylinder 5) has a malfunction. |
| 158B00 | P03C0 | The combustion chamber pressure sensor (cylinder 5) has a short circuit to positive. |
| 158C00 | P03BF | The combustion chamber pressure sensor (cylinder 5) has a short circuit to ground. |
| 158D00 | P03CB | The combustion chamber pressure sensor (cylinder 6) has a malfunction. |
| 158E00 | P03C8 | The combustion chamber pressure sensor (cylinder 6) has a malfunction. |
| 158F00 | P03CA | The combustion chamber pressure sensor (cylinder 6) has a short circuit to positive. |
| 159000 | P03C9 | The combustion chamber pressure sensor (cylinder 6) has a short circuit to ground. |
| 159100 | P244A | The pressure differential in the diesel particulate filter is too low. |
| 159200 | P244A | The pressure differential in the diesel particulate filter is too low. |
| 159300 | P0471 | Component 'B60 (Exhaust back pressure sensor)' has an internal fault. |
| 159400 | P0471 | Component 'B60 (Exhaust back pressure sensor)' has an internal fault. |
| 159500 | P0473 | Component B60 (Exhaust back pressure sensor) has a short circuit to positive. |
| 159600 | P0472 | Component B60 (Exhaust back pressure sensor) has a short circuit to ground. |
| 159700 | P2081 | The signal from component B19/11 (Temperature sensor upstream of turbocharger) is implausible. |
| 159800 | P2080 | The signal from component B19/11 (Temperature sensor upstream of turbocharger) is implausible. (Sensor drift) |
| 159900 | P2080 | The signal from component B19/11 (Temperature sensor upstream of turbocharger) is implausible. The signal change rate is below the permissible limit value. |
| 159A00 | P0546 | Component B19/11 (Temperature sensor upstream of turbocharger) has a short circuit to positive. |
| 159B00 | P0545 | Component B19/11 (Temperature sensor upstream of turbocharger) has a short circuit to ground. |
| 159C00 | P0236 | Component 'B5/1 (Charge pressure sensor)' has an internal fault. |
| 159D00 | P0238 | Component B5/1 (Charge pressure sensor) has a short circuit to positive. |
| 159E00 | P0237 | Component B5/1 (Charge pressure sensor) has a short circuit to ground. |
| 159F00 | P060A | Fault in CAN communication with control unit N3/9 (CDI control unit). |
| 15A000 | P060A | Control module has an internal error. |
| 15A100 | P060A | Control module has an internal error. |
| 15A200 | P060A | Control module has an internal error. |
| 15A300 | P060A | Control module has an internal error. |
| 15A400 | P060A | Control module has an internal error. |
| 15A700 | - | Component 'Y77/1 (Charge pressure positioner)' has an internal fault. |
| 15A800 | - | Component 'Y77/1 (Charge pressure positioner)' has an internal fault. |
| 15AB00 | P2176 | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15AC00 | P2119 | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15AD00 | P2111 | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15AE00 | P1999 | This function is not yet supported by the control unit. |
| 15AF00 | - | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15B000 | - | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15B100 | - | The signal from component M16/6 (Throttle valve actuator) is implausible. |
| 15B200 | P0123 | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15B300 | P0122 | Component 'M16/6 (Throttle valve actuator)' has an internal fault. |
| 15BA00 | P06B5 | This function is not yet supported by the control unit. |
| 15BB00 | P06B4 | This function is not yet supported by the control unit. |
| 15BC00 | - | This function is not yet supported by the control unit. |
| 15BD00 | - | This function is not yet supported by the control unit. |
| 15CF00 | P2101 | Component M16/6 (Throttle valve actuator) has a plausibility error. |
| 15D000 | P2101 | Component M16/6 (Throttle valve actuator) has a plausibility error. |
| 15D100 | - | This function is not yet supported by the control unit. |
| 15D200 | P1999 | This function is not yet supported by the control unit. |
| 15D300 | - | This function is not yet supported by the control unit. |
| 15D400 | - | This function is not yet supported by the control unit. |
| 15D500 | - | This function is not yet supported by the control unit. |
| 15D600 | - | This function is not yet supported by the control unit. |
| 15D700 | - | This function is not yet supported by the control unit. |
| 15D800 | - | This function is not yet supported by the control unit. |
| 15D900 | - | This function is not yet supported by the control unit. |
| 15DA00 | - | This function is not yet supported by the control unit. |
| 15DB00 | - | This function is not yet supported by the control unit. |
| 15DC00 | - | This function is not yet supported by the control unit. |
| 15DD00 | - | This function is not yet supported by the control unit. |
| 15DE00 | - | This function is not yet supported by the control unit. |
| 15DF00 | - | This function is not yet supported by the control unit. |
| 15E000 | - | This function is not yet supported by the control unit. |
| 15E300 | P2457 | Component B16/14 (Exhaust gas recirculation temperature sensor) has a plausibility error. |
| 15E600 | P257D | The status of component 'Engine hood' is implausible. |
| 15E700 | P0A0F | Control module has an internal error. |
| 15E800 | P060B | This function is not yet supported by the control unit. |
| 15E900 | - | This function is not yet supported by the control unit. |
| 15EA00 | P0A0F | The fill level of the AdBlue tank is too low or there is a fault in the AdBlue system. |
| 15EB00 | P2BA7 | The fill level of the AdBlue tank is too low or there is a fault in the AdBlue system. |
| 15EC00 | P2BA7 | The fill level of the AdBlue tank is too low or there is a fault in the AdBlue system. |
| 15ED00 | P2BA7 | The AdBlue® fill level is too low. |
| 15EE00 | P2BA7 | The AdBlue® fill level is too low. |
| 15EF00 | P2BA7 | The AdBlue® fill level is too low. |
| 15F000 | - | Component M55 (Inlet port shutoff motor) has excess temperature. |
| 15F100 | - | Component 'M55 (Inlet port shutoff motor)' has an internal fault. |
| 15F200 | - | Component is not installed. |
| 15F300 | P007E | The value of component B17/8 (Charge air temperature sensor) is implausible. Temperature change too fast |
| 15F400 | P007B | The learned values for component B17/8 (Charge air temperature sensor) are outside the permissible range. |
| 15F500 | P007D | The signal voltage of component B17/8 (Charge air temperature sensor) is too high. |
| 15F600 | P007C | The signal voltage of component B17/8 (Charge air temperature sensor) is too low. |
| 15F700 | P0426 | The value of component B19/11 (Temperature sensor upstream of turbocharger) is implausible. Temperature change too fast |
| 15F800 | P0426 | The learned values for component B19/11 (Temperature sensor upstream of turbocharger) are outside the permissible range. |
| 15F900 | P0426 | This function is not yet supported by the control unit. |
| 15FA00 | P0428 | Component B19/11 (Temperature sensor upstream of turbocharger) has a short circuit to positive. |
| 15FB00 | P0427 | Component B19/11 (Temperature sensor upstream of turbocharger) has a short circuit to ground. |
| 15FC00 | P2453 | The learned values for component B28/8 (Differential pressure sensor (DPF)) are outside the permissible range. |
| 15FD00 | P244A | The lower limit value of component B28/8 (Differential pressure sensor (DPF)) was dropped below/not reached. |
| 15FE00 | P2455 | The signal voltage of component B28/8 (Differential pressure sensor (DPF)) is too high. |
| 15FF00 | P2454 | The lower limit value of component B28/8 (Differential pressure sensor (DPF)) was dropped below/not reached. |
| 160000 | P0119 | This function is not yet supported by the control unit. |
| 160100 | - | This function is not yet supported by the control unit. |
| 160200 | P0118 | Coolant temperature sensor 1 has an electrical fault. There is a short circuit to positive. |
| 160300 | P0117 | This function is not yet supported by the control unit. |
| 160400 | P040E | The signal from component B16/14 (Exhaust gas recirculation temperature sensor) is implausible. The signal change rate is above the permissible limit value. |
| 160500 | P040B | The signal from component B16/14 (Exhaust gas recirculation temperature sensor) is implausible. The signal change rate is above the permissible limit value. |
| 160600 | P040B | The signal from component B16/14 (Exhaust gas recirculation temperature sensor) is implausible. The signal change rate is below the permissible limit value. |
| 160700 | P040D | Component B16/14 (Exhaust gas recirculation temperature sensor) has a short circuit to positive. |
| 160800 | P040C | Component B16/14 (Exhaust gas recirculation temperature sensor) has a short circuit to ground. |
| 160900 | P0199 | Component B1 (Oil temperature sensor) has a malfunction. |
| 160A00 | P0196 | Component B1 (Oil temperature sensor) has a plausibility error. |
| 160B00 | P0198 | The upper limit value of component B1 (Oil temperature sensor) has been reached. |
| 160C00 | P0197 | The lower limit value of component B1 (Oil temperature sensor) has been reached. |
| 160D00 | P0184 | The signal from component B50 (Fuel temperature sensor) is implausible. Temperature change too fast |
| 160E00 | P008F | The learned values for component B50 (Fuel temperature sensor) are outside the permissible range. |
| 160F00 | P0183 | The signal voltage of component B50 (Fuel temperature sensor) is too high. |
| 161000 | P0182 | The signal voltage of component B50 (Fuel temperature sensor) is too low. |
| 161100 | P006D | Component B28/5 (Pressure sensor downstream of air filter) has a plausibility error. |
| 161200 | P0108 | The signal voltage of component B28/5 (Pressure sensor downstream of air filter) is too high. |
| 161300 | P0107 | The lower limit value of component B28/5 (Pressure sensor downstream of air filter) was dropped below/not reached. |
| 161400 | P00AD | Component B2/6b1 (Left intake air temperature sensor) not within permissible range of values On/off ratio of reference signal is outside of permissible range. |
| 161500 | P00AD | Component B2/6b1 (Left intake air temperature sensor) not within permissible range of values There is a frequency or pulse width modulation fault. |
| 161600 | P00AB | The learned values for component B2/6b1 (Left intake air temperature sensor) are outside the permissible range. |
| 161700 | P0113 | Component B2/7b1 (Right intake air temperature sensor) not within permissible range of values On/off ratio of reference signal is outside of permissible range. |
| 161800 | - | Component B2/7b1 (Right intake air temperature sensor) not within permissible range of values There is a frequency or pulse width modulation fault. |
| 161900 | - | The learned values for component B2/7b1 (Right intake air temperature sensor) are outside the permissible range. |
| 161A00 | P042B | The difference between the current measurement and the most recent measurement of the exhaust gas temperature from component B19 (Catalytic converter temperature sensor) is too great. |
| 161B00 | P042B | The learned values for component B19 (TWC temperature sensor) are outside the permissible range. |
| 161C00 | P042B | Component B19 (TWC temperature sensor) has a plausibility error. |
| 161D00 | P042D | The signal voltage of component B19 (TWC temperature sensor) is too high. |
| 161E00 | P042C | The signal voltage of component B19 (TWC temperature sensor) is too low. |
| 161F00 | P242E | The temperature rise at component 'B16/15 (Temperature sensor upstream of SCR catalytic converter)' is too great. |
| 162000 | P242B | The signal from component B16/15 (Temperature sensor upstream of SCR catalytic converter) is implausible. |
| 162100 | P242B | The temperature increase at component 'B16/15 (Temperature sensor upstream of SCR catalytic converter)' is too low. |
| 162200 | P242D | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a short circuit to positive. |
| 162300 | P242C | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a short circuit to ground. |
| 162400 | P2264 | Component 'B76/1 (Condensation sensor for fuel filter with heating element)' has an internal fault. |
| 162500 | P2269 | The water content of the fuel filter has reached the upper limit value. |
| 162600 | P050E | Component Y27/9 (Exhaust gas recirculation positioner) has a plausibility error. |
| 162700 | P0404 | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 162800 | - | This function is not yet supported by the control unit. |
| 162900 | P0611 | This function is not yet supported by the control unit. |
| 162A00 | P049D | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 162B00 | P049D | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 162C00 | P049D | Component Y27/9 (Exhaust gas recirculation positioner) has a short circuit to ground. |
| 162D00 | P049D | Component Y27/9 (Exhaust gas recirculation positioner) has a short circuit to positive. |
| 163300 | P0404 | Component Y27/9 (Exhaust gas recirculation positioner) is stiff or blocked. |
| 163500 | P0420 | There is an internal fault in component G3/2 (O2 sensor upstream of KAT). |
| 163600 | P0420 | There is an internal fault in component G3/2 (O2 sensor upstream of KAT). |
| 163700 | - | Component 'G2 (generator)' has an internal fault. |
| 163800 | - | Component G2 (generator) has excess temperature. |
| 163900 | - | Component G2 (generator) has a short circuit to positive. |
| 163A00 | - | Component G2 (generator) has a short circuit to ground. |
| 163B00 | P2263 | Component 'Y77/1 (Charge pressure positioner)' has an internal fault. |
| 163C00 | P0000 | Abortion of engine start |
| 164000 | P2635 | Component 'M3 (Fuel pump)' has an internal fault. (Emergency running mode) |
| 164100 | P062A | Component 'M3 (Fuel pump)' has an internal fault. |
| 164200 | P0627 | Component M3 (Fuel pump) has an open circuit in the wiring. |
| 164300 | P0627 | Component M3 (Fuel pump) has a short circuit. |
| 164400 | P2635 | Component 'M3 (Fuel pump)' has an internal fault. |
| 164500 | P018B | The signal from component B4/6 (Rail pressure sensor) is implausible. |
| 164600 | P018A | The voltage supply for component B4/6 (Rail pressure sensor) is not OK. |
| 164700 | P018D | Component B4/6 (Rail pressure sensor) has a short circuit to positive. |
| 164800 | P018C | Component B4/6 (Rail pressure sensor) has a short circuit to ground. |
| 164900 | - | The signal from component B50 (Fuel temperature sensor) is implausible. |
| 165F00 | - | This function is not yet supported by the control unit. |
| 166000 | P2186 | This function is not yet supported by the control unit. |
| 166100 | - | This function is not yet supported by the control unit. |
| 166200 | - | This function is not yet supported by the control unit. |
| 166300 | P2185 | This function is not yet supported by the control unit. |
| 166400 | P2184 | This function is not yet supported by the control unit. |
| 166500 | P0396 | This function is not yet supported by the control unit. |
| 166600 | P03A0 | This function is not yet supported by the control unit. |
| 166700 | P03AA | This function is not yet supported by the control unit. |
| 166800 | P03B4 | This function is not yet supported by the control unit. |
| 166900 | P03BE | This function is not yet supported by the control unit. |
| 166A00 | P03C8 | This function is not yet supported by the control unit. |
| 166B00 | P245F | This function is not yet supported by the control unit. |
| 166C00 | P2464 | This function is not yet supported by the control unit. |
| 166D00 | P245F | This function is not yet supported by the control unit. |
| 166E00 | P2461 | This function is not yet supported by the control unit. |
| 166F00 | P2460 | This function is not yet supported by the control unit. |
| 167000 | P2453 | The input for differential pressure sensor 1 in the diesel particulate filter has a malfunction. There is an implausible signal. |
| 167100 | P0116 | Component B11/4 (Coolant temperature sensor) has a malfunction. |
| 167200 | P0116 | This function is not yet supported by the control unit. |
| 167300 | - | This function is not yet supported by the control unit. |
| 167400 | P0196 | This function is not yet supported by the control unit. |
| 167500 | P00AB | The value of component B2/6b1 (Left intake air temperature sensor) is implausible. |
| 167600 | P0111 | The value of component B2/7b1 (Right intake air temperature sensor) is implausible. |
| 167700 | - | This function is not yet supported by the control unit. |
| 167800 | - | This function is not yet supported by the control unit. |
| 167900 | - | This function is not yet supported by the control unit. |
| 167A00 | - | This function is not yet supported by the control unit. |
| 167B00 | - | This function is not yet supported by the control unit. |
| 167C00 | - | This function is not yet supported by the control unit. |
| 167D00 | - | This function is not yet supported by the control unit. |
| 167E00 | - | This function is not yet supported by the control unit. |
| 167F00 | - | This function is not yet supported by the control unit. |
| 168000 | - | This function is not yet supported by the control unit. |
| 168100 | - | This function is not yet supported by the control unit. |
| 168200 | - | This function is not yet supported by the control unit. |
| 168300 | - | This function is not yet supported by the control unit. |
| 168400 | - | This function is not yet supported by the control unit. |
| 168500 | - | This function is not yet supported by the control unit. |
| 168600 | - | This function is not yet supported by the control unit. |
| 168700 | - | This function is not yet supported by the control unit. |
| 168800 | U0120 | This function is not yet supported by the control unit. |
| 168900 | U0120 | This function is not yet supported by the control unit. |
| 168B00 | P0A14 | Component Switchable engine mount has a short circuit to ground or an open circuit. |
| 168C00 | P0607 | This function is not yet supported by the control unit. |
| 168D00 | P0A16 | Components 'Y123 (Left switchable engine mount)' and 'Y123/1 (Right switchable engine mount)' have a short circuit to positive. |
| 168E00 | P0A15 | Components 'Y123 (Left switchable engine mount)' and 'Y123/1 (Right switchable engine mount)' have a short circuit to ground. |
| 168F00 | P0669 | Component N118/5 (AdBlue® control unit) has excess temperature. |
| 169000 | P0668 | Component N118/5 (AdBlue® control unit) has excess temperature. |
| 169100 | - | Component 'B16/14 (Exhaust gas recirculation temperature sensor)' has an internal fault. |
| 169200 | P0667 | The control unit 'combustion engine' has overtemperature. |
| 169500 | P0607 | This function is not yet supported by the control unit. |
| 169600 | P0617 | Starter control has short circuit to positive. |
| 169700 | P0617 | Starter control has short circuit to positive. |
| 169800 | P0616 | Starter control has short circuit to ground. |
| 169900 | P0616 | Starter control has short circuit to ground. |
| 169A00 | P06D8 | The supply voltage to the sensors is outside the valid range. |
| 169B00 | P0512 | This function is not yet supported by the control unit. |
| 169C00 | P06DA | This function is not yet supported by the control unit. |
| 169D00 | P0607 | This function is not yet supported by the control unit. |
| 169E00 | P06DC | This function is not yet supported by the control unit. |
| 169F00 | P06DB | This function is not yet supported by the control unit. |
| 16A000 | P06DA | This function is not yet supported by the control unit. |
| 16A100 | P0607 | This function is not yet supported by the control unit. |
| 16A200 | P06DC | This function is not yet supported by the control unit. |
| 16A300 | P06DB | This function is not yet supported by the control unit. |
| 16A400 | P0480 | The output of electric fan 1 has an electrical fault or an open circuit. There is an internal fault. |
| 16A500 | P0480 | The output of electric fan 1 has an electrical fault or an open circuit. There is a component fault. |
| 16A600 | - | There is an internal fault in component N118/5 (AdBlue® control unit). |
| 16A700 | P007B | This function is not yet supported by the control unit. |
| 16A800 | P250B | This function is not yet supported by the control unit. |
| 16A900 | P252B | This function is not yet supported by the control unit. |
| 16AA00 | P252B | This function is not yet supported by the control unit. |
| 16AB00 | P0196 | This function is not yet supported by the control unit. |
| 16AC00 | P0196 | This function is not yet supported by the control unit. |
| 16AD00 | P252B | This function is not yet supported by the control unit. |
| 16AE00 | P252B | This function is not yet supported by the control unit. |
| 16AF00 | P250B | This function is not yet supported by the control unit. |
| 16B000 | P0196 | This function is not yet supported by the control unit. |
| 16B100 | - | This function is not yet supported by the control unit. |
| 16B200 | P0380 | Component B76/1 (Condensation sensor for fuel filter with heating element) has an open circuit. |
| 16B300 | P0380 | The signal from component B76/1 (Condensation sensor for fuel filter with heating element) is implausible. |
| 16B400 | P0380 | Component B76/1 (Condensation sensor for fuel filter with heating element) has a short circuit. |
| 16B500 | P0670 | Component B76/1 (Condensation sensor for fuel filter with heating element) has an open circuit. |
| 16B600 | P0670 | Component B76/1 (Condensation sensor for fuel filter with heating element) has a short circuit. |
| 16B700 | P0236 | This function is not yet supported by the control unit. |
| 16B800 | P0611 | This function is not yet supported by the control unit. |
| 16B900 | P0611 | This function is not yet supported by the control unit. |
| 16BA00 | - | This function is not yet supported by the control unit. |
| 16BB00 | P0611 | This function is not yet supported by the control unit. |
| 16BC00 | P0611 | This function is not yet supported by the control unit. |
| 16BD00 | P0611 | This function is not yet supported by the control unit. |
| 16BE00 | P0611 | This function is not yet supported by the control unit. |
| 16BF00 | P0611 | This function is not yet supported by the control unit. |
| 16C000 | P0611 | This function is not yet supported by the control unit. |
| 16C100 | P0300 | Combustion misfirings |
| 16C200 | P0301 | This function is not yet supported by the control unit. |
| 16C300 | P0304 | This function is not yet supported by the control unit. |
| 16C400 | P0302 | This function is not yet supported by the control unit. |
| 16C500 | P0305 | This function is not yet supported by the control unit. |
| 16C600 | P0303 | This function is not yet supported by the control unit. |
| 16C700 | P0306 | This function is not yet supported by the control unit. |
| 16C800 | P0638 | This function is not yet supported by the control unit. |
| 16C900 | P1999 | The voltage supply for component N74 (Soot particulate sensor control unit) is not OK. |
| 16CA00 | - | The power consumption of component 'N74 (Soot particulate sensor control unit)' is too high. |
| 16CB00 | P1999 | The temperature sensor in the soot particulate sensor has an electrical fault. |
| 16CC00 | P2BA7 | The AdBlue® fill level is too low. |
| 16CD00 | P2BA7 | The AdBlue® fill level is too low. Frequency counter 'Possible engine starts' is active. |
| 16CE00 | P2BA8 | The test of the AdBlue system has not yet been carried out. Frequency counter 'Possible engine starts' is active. |
| 16CF00 | P2BA8 | The test of the AdBlue system has not yet been carried out. Frequency counter 'Possible engine starts' is active. |
| 16D000 | P2BA7 | The AdBlue® fill level is too low. |
| 16D100 | P2BA7 | The AdBlue® fill level is too low. The remaining driving distance is limited. |
| 16D200 | P2BA7 | Starting the engine is not possible due to a low AdBlue fill level. |
| 16D300 | P2BA8 | The test of the AdBlue system has not yet been carried out. The remaining driving distance is limited. |
| 16D400 | P2BA8 | The test of the AdBlue system has not yet been carried out. The remaining driving distance is limited. |
| 16D500 | P2BA8 | The test of the AdBlue system has not yet been carried out. Engine start is not possible. |
| 16D600 | P0148 | The deviation between the measured and calculated fuel pressure in the low-pressure circuit is too high. |
| 16D700 | P008A | The pressure in the fuel low pressure circuit is too low. |
| 16D800 | P0607 | This function is not yet supported by the control unit. |
| 16D900 | P0234 | This function is not yet supported by the control unit. |
| 16DA00 | P0299 | This function is not yet supported by the control unit. |
| 16DB00 | P0299 | The negative control deviation during boost pressure control is too high. |
| 16DC00 | P0234 | This function is not yet supported by the control unit. |
| 16DD00 | P02E1 | This function is not yet supported by the control unit. |
| 16DE00 | P02E1 | This function is not yet supported by the control unit. |
| 16DF00 | P02E1 | This function is not yet supported by the control unit. |
| 16E000 | P02E1 | This function is not yet supported by the control unit. |
| 16E100 | P0299 | The boost pressure of turbocharger 1 is too low. |
| 16E200 | P0234 | This function is not yet supported by the control unit. |
| 16E300 | P0610 | This function is not yet supported by the control unit. |
| 16E400 | P2453 | This function is not yet supported by the control unit. |
| 16E500 | P0196 | This function is not yet supported by the control unit. |
| 16E600 | P0181 | The signal of component 'B50 (Fuel temperature sensor)' is implausible. |
| 16E700 | - | Fault in CAN communication with component N74 (Soot particulate sensor control unit). |
| 16E800 | P06A0 | The output for component 'AC compressor' has an electrical fault or open circuit. |
| 16E900 | P06A0 | This function is not yet supported by the control unit. |
| 16EA00 | P06A2 | This function is not yet supported by the control unit. |
| 16EB00 | P06A1 | This function is not yet supported by the control unit. |
| 16F000 | P1999 | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| 16F100 | P0A0F | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| 16F200 | P0A0F | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| 16F300 | P0A0F | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| 16F400 | P0A0F | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| 16F500 | P0426 | This function is not yet supported by the control unit. |
| 16FA00 | P242F | This function is not yet supported by the control unit. |
| 16FB00 | P2080 | The signal from component B19/11 (Temperature sensor upstream of turbocharger) is implausible. The signal comparison is faulty. |
| 16FC00 | P0111 | This function is not yet supported by the control unit. |
| 16FD00 | P0111 | The signal of component 'B2/7b1 (Right intake air temperature sensor)' is implausible. |
| 16FE00 | P042B | Temperature sensor 2 'Catalytic converter' (cylinder bank 1) has a malfunction. The signal comparison is faulty. |
| 16FF00 | P242B | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 170400 | P246B | Plausibility error due to defective exhaust gas pressure lines between diesel particulate filter and differential pressure sensor |
| 170500 | - | The efficiency of the diesel particulate filter (cylinder bank 1) is not sufficient. |
| 170600 | - | Component 'Battery isolating switch' has an internal fault. |
| 170700 | - | Component Battery isolating switch has excess temperature. |
| 170800 | - | Component Battery isolating switch has a short circuit to positive. |
| 170900 | - | Component Battery isolating switch has a short circuit to ground. |
| 170A00 | - | Component Atmospheric pressure sensor has a plausibility error. |
| 170B00 | - | Component Atmospheric pressure sensor has a short circuit to positive. |
| 170C00 | - | Component Atmospheric pressure sensor has a short circuit to ground. |
| 170E00 | - | Component S43 (Oil level indicator switch) has a plausibility error. |
| 170F00 | - | Component is not installed. |
| 171000 | - | The injection was shutoff by the 'Automatic engine start/stop' function. |
| 171100 | - | Component B79/2 (Transmission neutral position sensor) has a short circuit to positive. |
| 171200 | - | Component B79/2 (Transmission neutral position sensor) has a short circuit to ground. |
| 171300 | - | Component B79/2 (Transmission neutral position sensor) has a plausibility error. |
| 171400 | - | Component B79/2 (Transmission neutral position sensor) has a plausibility error. |
| 171500 | - | The fuel filter is heavily soiled. |
| 171600 | - | The fuel filter is contaminated. |
| 171800 | - | Internal control unit fault for active drivetrain |
| 171900 | - | Incorrect variant coding in component N3/9 (CDI control unit) |
| 171B00 | - | Component B16/15 (Temperature sensor upstream of SCR catalytic converter) has a plausibility error. |
| 171D00 | - | Component is not installed. |
| 171E00 | - | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 171F00 | - | The lower limit value of component NOx sensor downstream of SCR catalytic converter was dropped below/not reached. |
| 172100 | - | The internal combustion engine was stalled by a malfunction in the automatic engine start/stop system. |
| 172200 | - | Component B14 (Ambient temperature display temperature sensor) has a short circuit to positive. |
| 172300 | - | Component B14 (Ambient temperature display temperature sensor) has a short circuit to ground. |
| 172400 | - | Component B14 (Ambient temperature display temperature sensor) has a plausibility error. |
| 172500 | - | Component B14 (Ambient temperature display temperature sensor) has an open circuit in the wiring. |
| 172800 | - | Component B28/8 (Pressure differential sensor (DPF)) has a malfunction. |
| 172C00 | - | Control module has an internal error. |
| 172D00 | - | Component is not installed. |
| 172E00 | - | Component is not installed. |
| 172F00 | - | Component is not installed. |
| 173000 | - | Component is not installed. |
| 173100 | - | Component is not installed. |
| 173200 | - | Component is not installed. |
| 173300 | - | Component is not installed. |
| 173400 | - | Component is not installed. |
| 173500 | - | Component is not installed. |
| 173600 | - | Component is not installed. |
| 173700 | - | Component is not installed. |
| 173800 | - | Component is not installed. |
| 173900 | - | Component is not installed. |
| 173A00 | - | Component is not installed. |
| 173B00 | - | Component is not installed. |
| 173C00 | - | Component is not installed. |
| 173D00 | - | Component is not installed. |
| 173E00 | - | Component is not installed. |
| 174E00 | - | Component is not installed. |
| 174F00 | - | Component is not installed. |
| 175000 | - | Component is not installed. |
| 175100 | - | Component is not installed. |
| 175200 | - | Component is not installed. |
| 175300 | - | Charge pressure deviation is too large. |
| 175400 | - | Component B5/1 (Charge pressure sensor) has an open circuit in the wiring. |
| 175500 | - | Component B5/1 (Charge pressure sensor) has a short circuit to positive. |
| 175600 | - | Component B5/1 (Charge pressure sensor) has a short circuit to ground. |
| 175700 | - | Component is not installed. |
| 175800 | - | Component is not installed. |
| 175900 | - | Component is not installed. |
| 175A00 | - | Component is not installed. |
| 175B00 | - | Component is not installed. |
| 176100 | - | Component B19/9 (Temperature sensor upstream of diesel particulate filter) has a short circuit to ground. |
| 176600 | - | Component is not installed. |
| 176700 | - | Component is not installed. |
| 176800 | - | Component is not installed. |
| 176900 | - | Component is not installed. |
| 176A00 | - | Component is not installed. |
| 176B00 | - | Component is not installed. |
| 176C00 | - | Component is not installed. |
| 176D00 | - | The value of component B2/7b1 (Right intake air temperature sensor) is implausible. |
| 176E00 | - | Component B2/7b1 (Right intake air temperature sensor) has a short circuit to positive. |
| 176F00 | - | Component B2/7b1 (Right intake air temperature sensor) has a short circuit to ground. |
| 177200 | - | Component is not installed. |
| 177400 | - | Component is not installed. |
| 177500 | - | Component is not installed. |
| 177600 | - | Component is not installed. |
| 177700 | - | Communication with NOx sensor 2 has a malfunction. |
| 177800 | - | Communication with NOx sensor 1 has a malfunction. |
| 177900 | - | Component is not installed. |
| 177A00 | - | Component is not installed. |
| 177B00 | - | Component is not installed. |
| 177C00 | - | Component is not installed. |
| 177D00 | - | This function is not yet supported by the control unit. |
| 177E00 | - | Plausibility error concerning gear information or direction sensing, or no reverse gear detection |
| 177F00 | - | Plausibility error concerning gear information or direction sensing, or no reverse gear detection |
| 178000 | - | Plausibility error concerning gear information or direction sensing, or no reverse gear detection |
| 178200 | - | Efficiency of SCR catalytic converter |
| 178300 | - | Efficiency of SCR catalytic converter |
| 178400 | - | Efficiency of SCR catalytic converter |
| 178500 | - | Efficiency of SCR catalytic converter |
| 178600 | - | Efficiency of SCR catalytic converter |
| 178700 | - | The upper limit value of component NOx sensor upstream of SCR catalytic converter has been exceeded. |
| 178800 | - | The lower limit value of component NOx sensor upstream of SCR catalytic converter has been reached. |
| 178900 | - | The value of component NOx sensor upstream of SCR catalytic converter does not change. |
| 178A00 | - | The upper limit value of component NOx sensor downstream of SCR catalytic converter has been exceeded. |
| 178B00 | - | Excessive nitrogen oxide emission due to low quality AdBlue |
| 178C00 | - | Excessive nitrogen oxide emission due to low quality AdBlue |
| 178D00 | - | Excessive nitrogen oxide emission due to low quality AdBlue |
| 178E00 | - | Excessive nitrogen oxide emission due to low quality AdBlue |
| 178F00 | - | Correction of the metered AdBlue quantity has not been performed. |
| 179000 | - | This function is not yet supported by the control unit. |
| 17A500 | - | Deviation between measured and calculated NOx concentration (upper plausibility limit) |
| 17B900 | - | Deviation between measured and calculated NOx concentration (lower plausibility limit) |
| 17CB00 | - | This function is not yet supported by the control unit. |
| 17CC00 | - | This function is not yet supported by the control unit. |
| 17CD00 | - | This function is not yet supported by the control unit. |
| 17CE00 | - | This function is not yet supported by the control unit. |
| 17CF00 | - | This function is not yet supported by the control unit. |
| 17D000 | - | This function is not yet supported by the control unit. |
| 17D100 | - | This function is not yet supported by the control unit. |
| 17D200 | - | This function is not yet supported by the control unit. |
| 17D300 | - | This function is not yet supported by the control unit. |
| 17D400 | - | This function is not yet supported by the control unit. |
| 17D500 | - | This function is not yet supported by the control unit. |
| 17D600 | - | This function is not yet supported by the control unit. |
| 17D700 | - | This function is not yet supported by the control unit. |
| 17D800 | - | This function is not yet supported by the control unit. |
| 17D900 | - | This function is not yet supported by the control unit. |
| 17DA00 | - | This function is not yet supported by the control unit. |
| 17E600 | - | The fill level of the AdBlue tank is too high. |
| 17E700 | - | The negative control deviation of exhaust gas recirculation control is too high. |
| 17E800 | - | The upper limit value of component B19/9 (Temperature sensor upstream of diesel particulate filter) has been exceeded. |
| 17E900 | - | The positive control deviation of exhaust gas recirculation control is too high. |
| 17EA00 | - | The positive control deviation during boost pressure control is too high. |
| 17EB00 | - | The negative control deviation during boost pressure control is too high. |
| 17EC00 | - | The remaining time for enabling of the AdBlue metering amount has elapsed. |
| 17ED00 | - | The upper limit value was exceeded during injection quantity monitoring. |
| 17EE00 | - | The lower limit value was dropped below during injection quantity monitoring. |
| 17EF00 | - | Pressure deviation to atmospheric pressure sensor in control unit too large |
| 17F000 | - | The crash signal has been detected. |
| 17F100 | - | This function is not yet supported by the control unit. |
| 17F200 | - | This function is not yet supported by the control unit. |
| 17F300 | - | This function is not yet supported by the control unit. |
| 17F400 | - | This function is not yet supported by the control unit. |
| 17F500 | - | This function is not yet supported by the control unit. |
| 17F600 | - | This function is not yet supported by the control unit. |
| 17F700 | - | This function is not yet supported by the control unit. |
| 17F800 | - | This function is not yet supported by the control unit. |
| 17F900 | - | This function is not yet supported by the control unit. |
| 17FA00 | - | This function is not yet supported by the control unit. |
| 17FB00 | - | This function is not yet supported by the control unit. |
| 17FC00 | - | This function is not yet supported by the control unit. |
| 17FD00 | - | This function is not yet supported by the control unit. |
| 17FE00 | - | This function is not yet supported by the control unit. |
| 17FF00 | - | This function is not yet supported by the control unit. |
| 180000 | - | This function is not yet supported by the control unit. |
| 180100 | - | This function is not yet supported by the control unit. |
| 180200 | - | This function is not yet supported by the control unit. |
| 180300 | - | This function is not yet supported by the control unit. |
| 180400 | - | This function is not yet supported by the control unit. |
| 180500 | - | This function is not yet supported by the control unit. |
| 180600 | - | This function is not yet supported by the control unit. |
| 180700 | - | This function is not yet supported by the control unit. |
| 180800 | - | This function is not yet supported by the control unit. |
| 180900 | - | Component R48 (Two-disk thermostat heating element) has an electrical fault. |
| 180A00 | - | Component is not installed. |
| 180B00 | - | Component is not installed. |
| 180C00 | - | Component is not installed. |
| 180D00 | - | Component is not installed. |
| 180E00 | - | Component is not installed. |
| 180F00 | - | Component is not installed. |
| 181000 | - | This function is not yet supported by the control unit. |
| 181100 | - | Component is not installed. |
| 181700 | - | Component is not installed. |
| 181800 | - | Component is not installed. |
| 181900 | - | Implausible data were received from the soot particulate sensor. |
| 181A00 | - | The soot particulate sensor has a malfunction. |
| 181B00 | - | The soot particulate sensor has a malfunction. |
| 181C00 | - | The soot particulate sensor has an electrical fault. |
| 181D00 | - | Component is not installed. |
| 181E00 | - | Component is not installed. |
| 181F00 | - | The soot particulate sensor has a malfunction. |
| 182000 | - | Component is not installed. |
| 182100 | - | The signal of component B96/1 (Left intake port shutoff end position sensor) is implausible in comparison to the signal of component B96/2 (Right intake port shutoff end position sensor). |
| 182200 | - | Component B96/2 (Right intake port shutoff end position sensor) has an electrical fault. |
| 182300 | - | Component B96/2 (Right intake port shutoff end position sensor) has an electrical fault. |
| 182400 | - | Component B96/1 (Left intake port shutoff end position sensor) has an electrical fault. |
| 182500 | - | Component B96/1 (Left intake port shutoff end position sensor) has an electrical fault. |
| 182600 | - | Component M55 (Inlet port shutoff motor) has undertemperature. |
| 182700 | - | The output signal of component M55 (Inlet port shutoff motor) is implausible. |
| 182800 | - | The output signal of component M55 (Inlet port shutoff motor) is implausible. |
| 182900 | - | Component 'M55 (Inlet port shutoff motor)' has an internal fault. |
| 182A00 | - | Component 'M55 (Inlet port shutoff motor)' has an internal fault. |
| 182B00 | - | Component M55 (Inlet port shutoff motor) or line to component has short circuit or open circuit. |
| 183500 | - | The rail pressure cannot be built up. |
| 183600 | - | Component M55 (Inlet port shutoff motor) has a short circuit to ground. |
| 183700 | - | Post injection 1 was deactivated for cold starts. |
| 183800 | - | Post injection 2 was deactivated for cold starts. |
| 183900 | - | The regeneration duration of the diesel particulate filter is not OK. |
| 183A00 | - | Component M55 (Inlet port shutoff motor) is mechanically damaged or it sticks. |
| 183B00 | - | Component M55 (Inlet port shutoff motor) is mechanically damaged or it sticks. |
| 183C00 | - | The monitoring function for quantity correction is not active. |
| 183D00 | - | Component Y27/9 (Left EGR positioner) is mechanically damaged or it sticks. |
| 183E00 | - | Component Y27/9 (Left EGR positioner) is mechanically damaged or it sticks. |
| 183F00 | - | Quantity correction is not active. |
| 184000 | - | Zero quantity calibration is not active. |
| 184700 | - | The positive control deviation during rail pressure regulation during cold starting is too high. |
| 184800 | - | The negative control deviation during rail pressure regulation during cold starting is too high. |
| 184900 | - | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 184A00 | - | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 184B00 | - | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 184C00 | - | The control deviation during rail pressure regulation via the quantity control valve is too high. |
| 184D00 | - | The control deviation during rail pressure regulation is too high. |
| 184E00 | - | The negative control deviation during rail pressure regulation during cold starting is too high. |
| 184F00 | - | The control deviation during rail pressure regulation via the pressure regulator valve is too high. |
| 185000 | - | The control deviation during rail pressure regulation via the pressure regulator valve is too high. |
| 185100 | - | The control deviation during rail pressure regulation is too low. |
| 185200 | - | The positive control deviation during rail pressure regulation during cold starting is too high. |
| 185300 | - | Component is not installed. |
| 185400 | - | Component is not installed. |
| 185500 | - | Component is not installed. |
| 185600 | - | The charge pressure control is faulty. |
| 185700 | - | Post injection 2 has a malfunction during a cold start. |
| 185800 | - | The SCR exhaust aftertreatment system has a malfunction. |
| 185A00 | - | Output 1 for power supply to the sensors has a short circuit to positive. |
| 185B00 | - | Output 1 for power supply to the sensors has a short circuit to ground. |
| 185C00 | - | Output 1 for power supply to the sensors has an electrical fault or open circuit. |
| 185D00 | - | Output 2 for power supply to the sensors has a short circuit to positive. |
| 185E00 | - | Output 2 for power supply to the sensors has a short circuit to ground. |
| 185F00 | - | Output 2 for the power supply of the sensors has an electrical fault or an open circuit. |
| 186000 | - | Output 3 for power supply to the sensors has a short circuit to positive. |
| 186100 | - | Output 3 for power supply to the sensors has a short circuit to ground. |
| 186200 | - | Output 3 for power supply to the sensors has an electrical fault or open circuit. |
| 186300 | - | The correction value of the fuel consumption is too high. |
| 186400 | - | The correction value of the fuel consumption is too low. |
| 186500 | - | Communication with the soot particulate sensor has a malfunction. |
| 186600 | - | The output heating of the soot particulate sensor has a malfunction. |
| 186700 | - | The output heating of the soot particulate sensor has a malfunction. |
| 186800 | - | The soot particulate sensor has a malfunction. |
| 186900 | - | The soot particulate sensor has an electrical fault. |
| 186A00 | - | The AdBlue quality is insufficient. |
| 186B00 | - | The AdBlue fill level is low. |
| 186C00 | - | The AdBlue fill level is low. |
| 186D00 | - | The AdBlue fill level is low. |
| 186E00 | - | The AdBlue fill level is low. |
| 186F00 | - | Component Y133 (Coolant pump switchover valve) has a malfunction. |
| 187000 | - | Component Y133 (Coolant pump switchover valve) has a malfunction. |
| 187100 | - | The signal of component 'Y27/9 (Left EGR positioner)' is implausible. |
| 187200 | - | The permissible limit value for the air mass was exceeded. |
| 187300 | - | The permissible limit value for the air mass was dropped below. |
| 187400 | - | The boost pressure is too high during a cold start. |
| 187500 | - | The boost pressure is too low during a cold start. |
| 187600 | - | Component is not installed. |
| 187700 | - | Component is not installed. |
| 187800 | - | Component is not installed. |
| 187900 | - | Component is not installed. |
| 187A00 | - | The boost pressure is too high during a cold start. |
| 187B00 | - | The boost pressure is too high during a cold start in partial load operation. |
| 187C00 | - | The boost pressure is too low during a cold start. |
| 187D00 | - | The boost pressure is too low during a cold start in partial load operation. |
| 187E00 | - | The NOx concentration upstream of the SCR catalytic converter is too high. |
| 187F00 | - | The NOx concentration downstream of the SCR catalytic converter is too high. |
| 188000 | - | Component Y27/9 (Left EGR positioner) has a malfunction. |
| 188100 | - | Component Y27/9 (Left EGR positioner) has a malfunction. |
| 188200 | - | Component Y27/9 (Left EGR positioner) has a malfunction. |
| 188300 | - | The AdBlue metering system has a malfunction. |
| 188400 | - | The AdBlue metering system has a malfunction. |
| 188500 | - | The AdBlue metering system has a malfunction. |
| 188600 | - | The fill level of the AdBlue tank is too low. |
| 188700 | - | Current AdBlue consumption is too high. |
| 188800 | - | Current AdBlue consumption is too high. |
| 188900 | - | Current AdBlue consumption is too high. |
| 188A00 | - | Poor AdBlue quality or insufficient AdBlue dosage |
| 188B00 | - | Poor AdBlue quality or insufficient AdBlue dosage |
| 188C00 | - | Poor AdBlue quality or insufficient AdBlue dosage |
| 188D00 | - | The AdBlue quality is insufficient. |
| 188E00 | - | The AdBlue quality is insufficient. |
| 188F00 | - | The AdBlue quality is insufficient. |
| 189000 | - | Component is not installed. |
| 189300 | - | Component is not installed. |
| 189400 | - | Component is not installed. |
| 189500 | - | Component is not installed. |
| 189600 | - | Component is not installed. |
| 189700 | - | Component is not installed. |
| 189800 | - | Component is not installed. |
| 189900 | - | Component is not installed. |
| 189A00 | - | Component is not installed. |
| 189B00 | - | Component is not installed. |
| 189C00 | - | Component is not installed. |
| 189D00 | - | Component is not installed. |
| 189E00 | - | Component is not installed. |
| 189F00 | - | The signal of component 'B17/8 (Charge air temperature sensor)' is implausible. |
| 18A000 | - | The signal of component 'Intake air temperature sensor' is implausible. |
| 18A100 | - | Component 'M55 (Inlet port shutoff motor)' sticks. |
| 18A400 | - | Component is not installed. |
| 18A500 | - | The output heating of the soot particulate sensor has a malfunction. |
| 18A600 | - | The soot particulate sensor has a malfunction. |
| 18A700 | - | The soot particulate sensor has a malfunction. |
| 18A800 | - | The signal of component 'N74 (Soot particulate sensor control unit)' is implausible. |
| 18A900 | - | The software configuration of control unit N74 (Soot particulate sensor control unit) is incorrect. |
| 18AA00 | - | Position sensor 1 for the throttle valve has a short circuit to positive. |
| 18AB00 | - | Position sensor 1 for the throttle valve has a malfunction. |
| 18AC00 | - | Component M16/6 (Throttle valve actuator) has excess temperature. |
| 18AD00 | - | The control deviation of component M16/6 (Throttle valve actuator) is too high. |
| 18AE00 | - | Learning of the throttle valve stop was unsuccessful. |
| 18AF00 | - | Component M16/6 (Throttle valve actuator) jams in opened position. |
| 18B000 | - | Component 'M16/6 (Throttle valve actuator)' sticks. |
| 18B100 | - | The internal temperature sensor of the control unit has a short circuit to positive. |
| 18B200 | - | The internal temperature sensor of the control unit has a short circuit to ground. |
| 18B300 | - | The internal temperature sensor of the control unit has a malfunction. |
| 18B500 | - | The power supply of the soot particulate sensor has a short circuit to ground. |
| 18B600 | - | The boost pressure is too high during a cold start. |
| 18B700 | - | The signal of component 'M55 (Inlet port shutoff motor)' is implausible. |
| 18B800 | - | The variation between the measured signal and the calculated signal of the NOx sensor downstream of the SCR catalytic converter is too high. |
| 18B900 | - | The variation between the measured signal and the calculated signal of the NOx sensor upstream of the SCR catalytic converter is too high. |
| 18BA00 | - | The signal of component 'NOx sensor downstream of SCR catalytic converter' is implausible. |
| 18BB00 | - | The signal of component 'NOx sensor downstream of SCR catalytic converter' is implausible. |
| 18BC00 | - | The upper limit value for long-term adaptation of the SCR exhaust aftertreatment system was exceeded. |
| 18BD00 | - | Poor AdBlue quality or insufficient AdBlue dosage |
| 18BF00 | - | The signal of component 'NOx sensor upstream of SCR catalytic converter' is implausible. |
| 18C400 | - | The variation between the measured signal and the calculated signal of the NOx sensor upstream of the SCR catalytic converter is too high. |
| 18C500 | - | The variation between the measured signal and the calculated signal of the NOx sensor downstream of the SCR catalytic converter is too high. |
| 18C600 | - | Quantity correction for smooth idling control for cylinder 1 is not within permissible tolerance. |
| 18C700 | - | Quantity correction for smooth idling control for cylinder 4 is not within permissible tolerance. |
| 18C800 | - | Quantity correction for smooth idling control for cylinder 2 is not within permissible tolerance. |
| 18C900 | - | Quantity correction for smooth idling control for cylinder 5 is not within permissible tolerance. |
| 18CA00 | - | Quantity correction for smooth idling control for cylinder 3 is not within permissible tolerance. |
| 18CB00 | - | Quantity correction for smooth idling control for cylinder 6 is not within permissible tolerance. |
| 18CC00 | - | The signal of component 'Y85 (EGR [AGR] cooler bypass flap switchover valve)' is implausible. |
| 18CE00 | - | The power consumption of component 'N74 (Soot particulate sensor control unit)' is too high. |
| 18CF00 | - | Component 'N74 (Soot particulate sensor control unit)' has an internal fault. |
| 18D100 | - | The SCR exhaust aftertreatment system has a malfunction. |
| 18D200 | - | The SCR exhaust aftertreatment system has a malfunction. |
| 18D300 | - | The SCR exhaust aftertreatment system has a malfunction. |
| 18D400 | - | Exhaust gas relevant data Zero quantity calibration |
| 18D500 | - | The rail pressure is too low during engine startup. |
| 18D700 | - | Component is not installed. |
| 18D800 | - | Component is not installed. |
| 18D900 | - | Component is not installed. |
| 18DA00 | - | Component is not installed. |
| 18DB00 | - | Oxygen sensor 1 (cylinder bank 1) has a delayed reaction. |
| 18DC00 | - | Component is not installed. |
| 18DD00 | - | Oxygen sensor 1 (cylinder bank 1) has a delayed reaction. |
| 18DE00 | - | Component is not installed. |
| 18DF00 | - | Component is not installed. |
| 18E000 | - | Component is not installed. |
| 18E100 | - | Component is not installed. |
| 18E200 | - | Component is not installed. |
| 18E300 | - | Component is not installed. |
| 18E400 | - | Component is not installed. |
| 18E500 | - | Component is not installed. |
| 18E600 | - | Component is not installed. |
| 18E700 | - | Component is not installed. |
| 18E800 | - | Component is not installed. |
| 18E900 | - | Component is not installed. |
| 18EA00 | - | Component is not installed. |
| 18EB00 | - | Component is not installed. |
| 18EC00 | - | Component is not installed. |
| 18ED00 | - | Component is not installed. |
| 18EE00 | - | Component is not installed. |
| 18EF00 | - | Component is not installed. |
| 18F000 | - | Component is not installed. |
| 18F100 | - | The signal of component 'Diesel particulate filter' is implausible. |
| 18F200 | - | Engine stop prevention is active. |
| 18F300 | - | The heater of component 'G3/2 (O2 sensor upstream of CAT)' has a malfunction. |
| 18F400 | - | Component M4/7 (Engine and AC electric suction fan with integrated control) has a malfunction. |
| 18F500 | - | Component is not installed. |
| 18F600 | - | The selector lever position is implausible. |
| 18F700 | - | The selector lever position is implausible. |
| 190000 | - | Component 'Y27/9 (Left EGR positioner)' has an internal fault. |
| 190100 | - | Component 'Y74 (Pressure regulator valve)' has an internal fault. |
| E100000 | - | One or more signals sent from control unit N22/7 (Comfort AAC push-button control module) via the CAN bus is implausible. |
| E100100 | - | CAN signal 'Torque request' from control unit N22/7 (Comfort AAC push-button control module) is implausible. |
| E102200 | - | No CAN message was received from control unit N118/5 (AdBlue® control unit). |
| E102300 | - | CAN signal 'Torque request' from control unit A89 (DTR controller unit) is implausible. |
| E102400 | - | One or more signals sent from control unit A89 (DTR controller unit) via the CAN bus is implausible. |
| E102A00 | - | One or more signals sent from control unit N2/7 (Restraint systems control unit) via the CAN bus is implausible. |
| E103000 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E103600 | - | One or more messages sent from control unit N47-5 (ESP control unit) via the CAN bus is implausible. |
| E103700 | - | CAN signal 'Stop lamp' from control unit N47-5 (ESP control unit) is implausible. |
| E103A00 | - | CAN controller: CAN bus OFF |
| E103B00 | - | CAN controller: CAN bus OFF |
| E103C00 | - | CAN controller: CAN bus OFF |
| E104000 | - | No CAN message was received from control unit N93 (Central gateway control unit). |
| E105400 | - | The request for fan output is implausible. |
| E105900 | - | One or more signals sent from control unit N47-5 (ESP control unit) via the CAN bus is implausible. |
| E105A00 | - | One or more signals sent from control unit N73 (EIS [EZS] control unit) via the CAN bus is implausible. |
| E105B00 | - | No CAN message was received from control unit N73 (EIS [EZS] control unit). |
| E105C00 | - | CAN signal 'Torque request' from control unit N47-5 (ESP control unit) is implausible. |
| E105D00 | - | One or more signals sent from control unit N47-5 (ESP control unit) via the CAN bus is implausible. |
| E105E00 | - | One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible. |
| E105F00 | - | One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible. |
| E106000 | - | One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible. |
| E106800 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E107B00 | - | One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible. |
| E109B00 | - | Control unit N3/9 (CDI control unit) has received no LIN message from component G2 (generator). |
| E10BB00 | - | One or more signals sent from control unit N22/7 (Comfort AAC push-button control module) via the CAN bus is implausible. |
| E10BC00 | - | No CAN message was received from control unit N22/7 (Comfort AAC push-button control module). |
| E10BD00 | - | No CAN message was received from control unit A1 (Instrument cluster). |
| E10F000 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E11AE00 | - | One or more signals sent from control unit Vehicle power supply control module via the CAN bus is implausible. |
| E11C800 | - | One or more signals sent from control unit N47-5 (ESP control unit) via the CAN bus is implausible. |
| E11C900 | - | No CAN message was received from control unit N47-5 (ESP control unit). |
| E11CB00 | - | One or more signals sent from control unit N80 (Steering column module) via the CAN bus is implausible. |
| E11CC00 | - | No CAN message was received from control unit N80 (Steering column module). |
| E11CE00 | - | One or more signals sent from control unit N51 (AIRmatic control unit) via the CAN bus is implausible. |
| E11CF00 | - | No CAN message was received from control unit N51 (AIRmatic control unit). |
| E11E500 | - | An internal control unit reset was performed. |
| E11FD00 | - | One or more signals sent from control unit N15/3 (ETC [EGS] control unit) via the CAN bus is implausible. |
| E11FE00 | - | CAN signal 'Torque request' from control unit N15/3 (ETC [EGS] control unit) is implausible. |
| E11FF00 | - | One or more signals sent from control unit N15/3 (Electronic transmission control, control unit) via the CAN bus is implausible. |
| E121800 | - | CAN signal 'Wheel speed' from control unit N47-5 (ESP control unit) is implausible. |
| E121900 | - | CAN signal 'Wheel speed' from control unit N47-5 (ESP control unit) is implausible. |
| E121A00 | - | No CAN message was received from control unit A80 (Intelligent servo module for DIRECT SELECT). |
| E121B00 | - | One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible. |
| E121E00 | - | The engine off time has an implausible value. |
| E121F00 | - | Control module has an internal error. |
| E122000 | - | CAN signal 'Ambient temperature' from control unit N22/7 (Automatic air conditioning control and operating unit) is implausible. |
| E122100 | - | No CAN message from control unit A13 (Electric parking brake control unit). |
| E122200 | - | No CAN message was received from control unit Electric parking brake. |
| E124900 | - | No CAN message was received from control unit N15/3 (ETC [EGS] control unit). |
| E124A00 | - | One or more signals sent from control unit A80 (Intelligent servo module for DIRECT SELECT) via the CAN bus is implausible. |
| E125100 | - | CAN signal 'Ambient temperature' from control unit N22/7 (Comfort AAC push-button control module) is implausible. |
| E125400 | - | CAN signal 'Ambient temperature' from control unit N22/7 (Comfort AAC push-button control module) is implausible. |
| E125900 | - | The idle speed increase was approved (active request). |
| E125B00 | - | The idle speed increase was approved (passive request). |
| E129B00 | - | No LIN message was received from component N14/3 (Glow output stage). |
| E129C00 | - | Transmission control (fault 1) |
| E129D00 | - | Transmission control (fault 10) |
| E129E00 | - | Transmission control (fault 11) |
| E129F00 | - | Transmission control (fault 12) |
| E12A000 | - | Transmission control (fault 13) |
| E12A100 | - | Transmission control (fault 14) |
| E12A200 | - | Transmission control (fault 15) |
| E12A300 | - | Transmission control (fault 16) |
| E12A400 | - | Transmission control (fault 17) |
| E12A500 | - | Transmission control (fault 18) |
| E12A600 | - | Transmission control (fault 19) |
| E12A700 | - | Transmission control (fault 2) |
| E12A800 | - | Transmission control (fault 20) |
| E12A900 | - | Transmission control (fault 21) |
| E12AA00 | - | Transmission control (fault 22) |
| E12AB00 | - | Transmission control (fault 23) |
| E12AC00 | - | Transmission control (fault 24) |
| E12AD00 | - | Transmission control (fault 25) |
| E12AE00 | - | Transmission control (fault 26) |
| E12AF00 | - | Transmission control (fault 27) |
| E12B000 | - | Transmission control (fault 28) |
| E12B100 | - | Transmission control (fault 29) |
| E12B200 | - | Transmission control (fault 3) |
| E12B300 | - | Transmission control (fault 30) |
| E12B400 | - | Transmission control (fault 31) |
| E12B500 | - | Transmission control (fault 32) |
| E12B600 | - | Transmission control (fault 4) |
| E12B700 | - | Transmission control (fault 5) |
| E12B800 | - | Transmission control (fault 6) |
| E12B900 | - | Transmission control (fault 7) |
| E12BA00 | - | Transmission control (fault 8) |
| E12BB00 | - | Transmission control (fault 9) |
| E12BF00 | - | This function is not yet supported by the control unit. |
| E134300 | - | No CAN message was received from control unit N118/5 (AdBlue® control unit). |
| E135000 | - | Component NOx sensor upstream of SCR catalytic converter has a plausibility error. |
| E143B00 | - | CAN signal 'Fuel level' from control unit A1 (Instrument cluster) is implausible. |
| E145800 | - | No CAN message was received from control unit N118 (Fuel pump control module). |
| E145900 | - | No CAN message was received from control unit N82 (Battery control module). |
| E145A00 | - | Component is not installed. |
| E145C00 | - | Control unit N47-5 (ESP control unit) requests reduced fan output due to undervoltage. |
| E146000 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E147A00 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E153900 | - | Efficiency of SCR catalytic converter |
| E153A00 | - | Efficiency of SCR catalytic converter |
| E154200 | - | No CAN message was received from control unit N73 (EIS [EZS] control unit). |
| E154A00 | - | No CAN message 'Maximum AdBlue metering amount' from control module N118/5 (AdBlue® control unit) or message is faulty. |
| E15A500 | - | Fault detection on monitoring of vehicle speed |
| E15A600 | - | No CAN message was received from control unit N2/7 (Restraint systems control unit). |
| E15AA00 | - | No CAN message was received from control unit N129 (Starter generator squib). |
| E15B600 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E15B700 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E15B800 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E15B900 | - | One or more signals sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E15E100 | - | CAN controller: CAN bus OFF |
| E15E200 | - | One or more signals sent from control unit N93 (Central gateway control unit) via the CAN bus is implausible. |
| E163400 | - | No CAN message was received from control unit N118/5 (AdBlue® control unit). |
| E163D00 | - | No CAN message was received from control unit N10 (SAM control unit). |
| E163E00 | - | One or more signals sent from control unit A80 (Intelligent servo module for DIRECT SELECT) via the CAN bus is implausible. |
| E163F00 | - | No CAN message was received from control unit A80 (Intelligent servo module for DIRECT SELECT). |
| E164A00 | - | One or more messages sent from control unit N129 (Starter generator squib) via the CAN bus is implausible. |
| E164C00 | - | One or more signals sent from control unit N15/7 (Transfer case control module) via the CAN bus is implausible. |
| E164D00 | - | No CAN message was received from control unit N15/7 (Transfer case control module). |
| E16F600 | - | Ignore fault. |
| E16F700 | - | Ignore fault. |
| E16F800 | - | Ignore fault. |
| E16F900 | - | Ignore fault. |
| E170000 | - | Ignore fault. |
| E170100 | - | Ignore fault. |
| E170200 | - | Ignore fault. |
| E170300 | - | Ignore fault. |
| E170D00 | - | No CAN message was received from control unit Battery management system. |
| E171700 | - | The maximum torque was exceeded. |
| E171A00 | - | No CAN message was received from control unit N62 (PTS control unit). |
| E171C00 | - | No LIN message was received from component Radiator blind. |
| E172600 | - | Hybrid CAN bus OFF fault |
| E172700 | - | Communication with control unit 'DC/DC converter' has a malfunction. |
| E172900 | - | No CAN message was received from control unit Electric motor. |
| E172A00 | - | One or more messages sent from control unit Electric motor via the CAN bus is implausible. |
| E172B00 | - | No CAN message received from component Electric motor. |
| E178100 | - | No CAN message was received from control unit N118/5 (AdBlue® control unit). |
| E181200 | - | One or more signals sent from control unit N15/3 (ETC [EGS] control unit) via the CAN bus is implausible. |
| E181300 | - | One or more signals sent from control unit N15/3 (ETC [EGS] control unit) via the CAN bus is implausible. |
| E185900 | - | Control module has an internal error. |
| E189100 | - | No CAN message was received from control unit Dr-side SAM. |
| E189200 | - | CAN controller: CAN bus OFF |
| E18A200 | - | No CAN message was received from control unit A1 (Instrument cluster). |
| E18A300 | - | Component is not installed. |
| E18B400 | - | One or more messages sent from control unit N118/5 (AdBlue® control unit) via the CAN bus is implausible. |
| E18CD00 | - | No or incorrect CAN message from control unit N2/7 (Restraint systems control unit) |
| E18D000 | - | Component is not installed. |